Newcon Optik LAM 10M IR Manuale utente
Operation Manual
LAM 10M IR
LASER AIMING MODULE /
TARGET POINTER
105 Sparks Ave., Toronto, ON, M2H 2S5, Canada
IMPORTANT INFORMATION
Read prior to activation
You have just purchased a sophisticated electronic device.
To operate it properly, please read this manual carefully.
LAM belongs to Class I laser products in accordance with
IEC 60825-1. Here are some common precautions that
must be observed.
•ALWAYS turn the device off when it is not in use
and when you change the battery!
•NEVER look into the beam
•NEVER subject LAM to excessive impacts
•NEVER transport LAM without the case
•NEVER disassemble LAM
•NEVER reverse polarity of the battery
•ALWAYS make sure that the device is fixed firmly
on the weapon
•ALWAYS remove battery when not in use for a long
period
•ALWAYS store in a warm dry place when not in use
•ALWAYS clean output windows with soft cloth only
•ALWAYS check the O-ring when replacing the
battery.
1
CONTENTS
1. Brief description ................................................. 2
2. Device design ..................................................... 3
3. DELIVERY SET ................................................ 8
3.1. Standard delivery set...................................... 8
3.2. Optional parts................................................. 8
4. Specifications...................................................... 9
5. OPERATION INSTRUCTIONS...................... 10
5.1. Installing the battery .................................... 10
5.2. Mounting LAM on a weapon....................... 10
5.3. Connecting the remote control..................... 11
5.4. Adjusting LAM on a weapon....................... 11
6. Maintenance, storage and transportation .......... 13
6.1. General......................................................... 13
6.2. Storage ......................................................... 14
6.3. Transportation.............................................. 15
7. TROUBLESHOOTING ................................... 17
8. WARRANTY ................................................... 18
9. CUSTOMER SUPPORT .................................. 19
10. QUALITY CERTIFICATE .............................. 20
2
Carefully read all the instructions prior to use.
Failure to obey the instructions will void the
warranty!
INVISIBLE LASER RADIATION
CLASS I LASER PRODUCT 830–860 nm 0,1mW.
1. Brief description
LAM 10M IR laser aimer (hereinafter referred as LAM) is
designed for precise aiming at night time. LAM forms an IR
laser radiation spot on the target visible only through the
night vision goggles. It can be attached to a weapon equipped
with Picatinny rail MIL-STD-1913.
Laser beam, created by a semiconductor laser diode, is
invisible by naked eye, while it is perfectly visible through
night vision goggles, rifle sights or hand-held devices.
LAM meets the Class 1 eye safety requirements.
Nevertheless users are not advised to look into the laser
beam.
3
2. Device design
17 16 14
8765432
1
4
Fig. 1. LAM 10M IR
1 – clamp 2 – bracket
3 – stopper 4 – remote connector
5 – body 6 – emitter
7 – emitter cap 8 – emitter protective cap
9 – windage adjustment 10 – fastener
11 – ‘laser on’ warning
indicator
12 – elevation adjustment
13 – fixation screw cap 14 – fixation screw
15 – battery compartment
cap
16 – battery compartment
17 – operating modes switch
14
13
11
12
109
5
LAM consists of an emitter (6,7, Fig.1), a battery
compartment (15,16, Fig.1), windage (9, Fig.1) and elevation
(12, Fig.1) adjustment mechanisms, an operating modes
switch (17, Fig.1), a remote switch (Fig.2), a clamp (1, Fig.1).
A battery is to be inserted into the battery compartment
(16, Fig.1). Battery compartment cap (15, Fig.1) is attached
to the body with a rubber band. The battery compartment is
sealed with rubber O-ring. A spare O-Ring is included in the
delivery set.
Emitter tube output window is closed with a cap (7, Fig.1)
with an output aperture. When not in operation, the aperture
is closed with a protective rubber cap (8, Fig.1).
LAM is activated by means of the operating modes switch
(17, Fig.1) and/or the remote switch (Fig.2). At switching
laser radiation on ‘laser on’ warning indicator 11 lights.
The switch (17, Fig.1) has the following positions:
Mode
OFF Off
C The aimer is on; Continuous live fire
R The aimer is on; Remote activation; live fire
6
LAM automatically turns off after 30 minutes of being
switched in positions C and R. In order to activate LAM after
it has automatically turned off, return the switch (17, Fig.1)
into OFF position and then switch it to the desired position
again.
The remote switch (Fig.2) can be attached to LAM by a
connector (3, Fig.2) with a union nut. When not in operation
the connector (4, Fig. 1) is covered with a cap. The remote
switch key (1, Fig.2) is attached to weapon pivot or grip with
velcro tape (2, Fig.3).
LAM is mounted on the Picatinny rail. An optional mount
enables mounting LAM on a weapon barrel. This mount’s
fitting diameter is 15 mm.
7
1 — key; 2 — velcro tape; 3 — connector
Fig. 2. Remote switch
1
2
3
Indice
Altri manuali Newcon Optik Cannocchiale da puntamento
Newcon Optik
Newcon Optik DN140M Manuale utente
Newcon Optik
Newcon Optik NVS 4 Manuale utente
Newcon Optik
Newcon Optik NVS-33 Manuale utente
Newcon Optik
Newcon Optik NC 3-12x50 Manuale utente
Newcon Optik
Newcon Optik NVS 22-2XT Manuale utente
Newcon Optik
Newcon Optik DN-140 Manuale utente
Newcon Optik
Newcon Optik DN482 Manuale utente
Newcon Optik
Newcon Optik DN 533 Manuale utente
Newcon Optik
Newcon Optik NVS 10MG Manuale utente
