NexSens X2-Cell Manuale utente

Serial Label

X2-Cell Quick Start

For best results, setup your new system in the office/lab. Collect a few data

points and become familiar with the system prior to field deployment.

1Go to V2.WQDataLIVE.com/Getting-Started

2Create a new account or sign into an existing account and enter the

Claim Code found on the serial label to access the device’s data

3Place the X2 in an area with

strong cellular coverage and

connect the antenna

4Remove the center power

plug and required outer port

plugs (1 for each sensor to

connect)

5Connect sensors to any outer

port (8 pin)

6Connect power (5 to 24VDC)

to the center port (6 pin)

7Wait up to 60 seconds for the blue cellular status LED to turn on

If the blue LED repeatedly blinks three times, the cellular strength is

sufficient to connect the X2 with WQData LIVE

If the blue LED repeatedly blinks once, cell coverage is low. Move the

X2 to a location with better cell coverage and cycle power

8Allow up to 5 minutes for sensor detection and data acquisition. The

detected X2 profile is sent to WQData LIVE along with new data

The blue LED will be on (solid) when setup is completed

9Refresh the web browser and confirm that all connected sensors and

their parameters are displayed on WQData LIVE

Troubleshooting

Symptom

Possible

Cause

Corrective Action

Claim code does

not work

Code was entered

wrong

Re-enter code exactly as shown on

serial label

Device was already

claimed

Check with previous owners/users

No LED activity

when power

plug connected

No power to the

device

Confirm the central power plug is

securely connected

Replace the battery pack

Device does not

show sensors

and parameters

or update new

data on WQData

LIVE

AND

Blue LED

repeatedly blinks

once

No cellular

coverage

Relocate the unit to an area with

strong cellular coverage and no

obstructions (outside in a parking

lot is typically good), then cycle the

power (Disconnect and reconnect

center power plug)

Sensors are

missing on

WQData LIVE

when setup is

complete

Sensors are not

configured properly

Confirm connected sensors do not

share SDI-12 or Modbus addresses

Sensors are not

supported

Confirm connected sensor is

compatible with the X2

Sensor is wired

incorrectly or

damaged

Ensure the sensor can properly

communicate directly without the

X2

For more assistance visit:

www.NexSens.com/Category/Knowledge-Base/X2-Data-Logger

Manuali Registratore di dati popolari di altre marche

TESTO

TESTO 176 Manuale utente

HT Italia

HT Italia XL421 Manuale utente

HBM

HBM SOMAT XR CX22B-R Manuale utente

Agtrix

Agtrix 380i Manuale utente

Hobo

Hobo H8 Pro Manuale utente

Beijing ART Tech

Beijing ART Tech PCI2320 Manuale utente

Athena

Athena GET SL1 Manuale utente

Motec Systems

Motec Systems C185 Manuale utente

Beijing ART Tech

Beijing ART Tech USB2832 Manuale utente

Rotronic

Rotronic HygroLog HL20 Manuale utente

MRC

MRC DW-6092 Manuale utente

Racelogic

Racelogic VBOX LapTimer Manuale utente

Edu-Logger

Edu-Logger 900-240 Manuale utente

Elma

Elma DT173 Manuale utente

MadgeTech

MadgeTech PRTemp140 Scheda tecnica

Comet

Comet U0121M Manuale utente

pico Technology

pico Technology PT-104 Manuale utente

Soil Instruments

Soil Instruments GTecLink Manuale utente