NI C Series Manuale utente
GETTING STARTED GUIDE
NI 9215
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input,
4-Channel C Series Voltage Input Module
This document explains how to connect to the NI 9215. In this
document, the NI 9215 with screw terminal, NI 9215 with spring
terminal, and NI 9215 with BNC are referred to inclusively as the
NI 9215.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9215. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Safety Guidelines
Operate the NI 9215 only as described in this document.
Caution Do not operate the NI 9215 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
built into the product if the product is damaged in any
2| ni.com | NI 9215 Getting Started Guide
way. If the product is damaged, return it to NI for
repair.
NI 9215 with Screw Terminal and NI 9215 with
Spring Terminal Safety Voltages
Connect only voltages that are within the following limits.
Channel-to-COM ±30 V maximum
Isolation
Channel-to-channel None
Channel-to-earth ground
Continuous 250 Vrms,
Measurement Category II
Withstand 2,300 Vrms, verified by a 5 s
dielectric withstand test
Measurement Category II is for measurements performed on
circuits directly connected to the electrical distribution system.
This category refers to local-level electrical distribution, such as
that provided by a standard wall outlet, for example, 115 V for
U.S. or 230 V for Europe.
NI 9215 Getting Started Guide | © National Instruments | 3
Caution Do not connect the NI 9215 to signals or use
for measurements within Measurement Categories III
or IV.
NI 9215 with BNC Safety Voltages
Connect only voltages that are within the following limits.
AI+-to-AI- ±30 V maximum
Isolation
Channel-to-channel None
Channel-to-earth ground
Continuous 60 VDC,
Measurement Category I
Withstand 1,500 Vrms, verified by a 5 s
dielectric withstand test
Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution system
referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This category is
for measurements of voltages from specially protected secondary
circuits. Such voltage measurements include signal levels, special
4| ni.com | NI 9215 Getting Started Guide
equipment, limited-energy parts of equipment, circuits powered
by regulated low-voltage sources, and electronics.
Note Measurement Categories CAT I and CAT O are
equivalent. These test and measurement circuits are not
intended for direct connection to the MAINS building
installations of Measurement Categories CAT II,
CAT III, or CAT IV.
Caution Do not connect the NI 9215 to signals or use
for measurements within Measurement Categories II,
III, or IV.
Safety Guidelines for Hazardous Voltages
You can connect hazardous voltages only to the NI 9215 with
screw terminal and the NI 9215 with spring terminal. Do not
connect hazardous voltages to the NI 9215 with BNC.
If hazardous voltages are connected to the device, take the
following precautions. A hazardous voltage is a voltage greater
than 42.4 Vpk voltage or 60 V DC to earth ground.
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
NI 9215 Getting Started Guide | © National Instruments | 5
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Caution Ensure that devices and circuits connected to
the module are properly insulated from human contact.
Caution When module terminals are hazardous
voltage LIVE (>42.4 Vpk/60 V DC), you must ensure
that devices and circuits connected to the module are
properly insulated from human contact. You must use
the NI 9927 connector backshell kit with the NI 9215
with screw terminal and the NI 9981 connector
backshell kit with the NI 9215 with spring terminal to
ensure that the terminals are not accessible.
Safety Guidelines for Hazardous Locations
The NI 9215 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
and Ex nA IIC T4 hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
NI 9215 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
6| ni.com | NI 9215 Getting Started Guide
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Division 2 and Zone 2 applications,
install the system in an enclosure rated to at least IP54
as defined by IEC/EN 60079-15.
Caution For Division 2 and Zone 2 applications,
connected signals must be within the following limits.
Capacitance 0.2 µF maximum
Special Conditions for Hazardous Locations Use in
Europe and Internationally
The NI 9215 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO 03 ATEX 0324020X and is IECEx UL 14.0089X
certified. Each NI 9215 is marked II 3G and is suitable for use
NI 9215 Getting Started Guide | © National Instruments | 7
in Zone 2 hazardous locations, in ambient temperatures of -40 °C
≤ Ta ≤ 70 °C. If you are using the NI 9215 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
Caution You must make sure that transient
disturbances do not exceed 140% of the rated voltage.
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC 60664-1.
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
8| ni.com | NI 9215 Getting Started Guide
Safety Compliance and Hazardous Locations
Standards
This product is designed to meet the requirements of the
following electrical equipment safety standards for measurement,
control, and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA C22.2 No. 61010-1
• EN 60079-0, EN 60079-15
• IEC 60079-0: Ed 6, IEC 60079-15; Ed 4
• UL 60079-0; Ed 6, UL 60079-15; Ed 4
• CSA C22.2 No. 60079-0, CSA C22.2 No. 60079-15
Note For UL and other safety certifications, refer to
the product label or the Product Certifications and
Declarations section.
NI 9215 Getting Started Guide | © National Instruments | 9
CE Compliance
This product meets the essential requirements of applicable
European Directives, as follows:
• 2014/35/EU; Low-Voltage Directive (safety)
• 2014/30/EU; Electromagnetic Compatibility Directive
(EMC)
• 2014/34/EU; Potentially Explosive Atmospheres (ATEX)
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
stated in the product specifications. These requirements and
limits provide reasonable protection against harmful interference
when the product is operated in the intended operational
electromagnetic environment.
This product is intended for use in industrial locations. However,
harmful interference may occur in some installations, when the
product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize
10 | ni.com | NI 9215 Getting Started Guide
Altri manuali per C Series
3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali NI Sistema I/O
NI
NI R Series Manuale utente
NI
NI SCC-CO20 Manuale utente
NI
NI WSN-3202 Manuale utente
NI
NI FieldPoint FP-DO-400 Manuale utente
NI
NI USB-9215 Series Manuale utente
NI
NI R Series Manuale utente
NI
NI FD-11605 Manuale
NI
NI SLSC-12202 Manuale utente
NI
NI 9234 Manuale per l'uso e la cura
NI
NI PXIe-7865 Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
