Nibe F135 Guida utente

Installer manual

LEK

NIBE™ F135

Exhaust air module

IHB GB 1540-3

331432

Table of Contents

21 Important information

2Safety information

52 Delivery and handling

5Transport

5Assembly

6Supplied components

7Removing the covers

83 The exhaust air module design

104 Pipe and air connections

10General pipe connections

11Dimensions and pipe connections

12Mounting

Connecting to indoor module and air-water

heat pump

13Installation alternative

16General air connections

17Exhaust air duct /kitchen fan

17Ventilation flow (exhaust air)

17Adjusting ventilation (exhaust air)

185 Electrical connections

18General

18Connections

19Optional connections

206 Commissioning and adjusting

20Preparations

20Filling and venting

21Start-up and inspection

237 Control - Introduction

238 Disturbances in comfort

23Info menu indoor module

23Manage alarm (NIBE Indoor module)

23Troubleshooting

259 Accessories

2610 Technical data

26Dimensions and setting-out coordinates

27Technical specifications

29Energy labelling

31Electrical circuit diagram

32Index

1Table of Contents |NIBE™ F135

Safety information

This manual describes installation and service proced-

ures for implementation by specialists.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Chil-

dren shall not play with the appliance.

Cleaning and user maintenance shall

not be made by children without super-

vision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2015.

Symbols

NOTE

This symbol indicates danger to machine or

person.

Caution

This symbol indicates important information

about what you should observe when main-

taining your installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

F135 is CE marked and fulfils IP21.

The CE marking means that NIBE ensures that the

product meets all regulations that are placed on it

based on relevant EU directives. The CE mark is obligat-

ory for most products sold in the EU, regardless where

they are made.

IP21 means that objects with a diameter larger than

or equivalent to 12.5 mm cannot penetrate and cause

damage and that the product is protected against

vertically falling drops of water.

Serial number

The serial number can be found to the left, on top of

F135.

LEK

Serial number

Caution

Always give the product's serial number (14

digits) when contacting your installer.

Country specific information

Installer manual

This installer manual must be left with the customer.

NIBE™ F135Chapter 1 | Important information2

1 Important information

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person.

DateSignatureNotesDescription

✔

Ventilation, exhaust air (page 13)

Setting the ventilation flow

Exhaust air filter

Heating medium (page 20)

System flushed

System vented

Circulation pump setting

Setting heating medium flow

Boiler pressure

Electricity (page 18)

Supply connected 230 V

Circuit fuses

3Chapter 1 | Important informationNIBE™ F135

Contact information

KNV Energietechnik GmbH, Gahberggasse 11, 4861 SchörflingAT

Tel: +43 (0)7662 8963-0 Fax: +43 (0)7662 8963-44 E-mail: mail@knv.at www.knv.at

NIBE Wärmetechnik c/o ait Schweiz AG, Industriepark, CH-6246 AltishofenCH

Tel: (52) 647 00 30 Fax: (52) 647 00 31 E-mail: [email protected] www.nibe.ch

Druzstevni zavody Drazice s.r.o, Drazice 69, CZ - 294 71 Benatky nad JizerouCZ

Tel: +420 326 373 801 Fax: +420 326 373 803 E-mail: [email protected] www.nibe.cz

NIBE Systemtechnik GmbH, Am Reiherpfahl 3, 29223 CelleDE

Tel: 05141/7546-0 Fax: 05141/7546-99 E-mail: [email protected] www.nibe.de

Vølund Varmeteknik A/S, Member of the Nibe Group, Brogårdsvej 7, 6920 VidebækDK

Tel: 97 17 20 33 Fax: 97 17 29 33 E-mail: [email protected] www.volundvt.dk

NIBE Energy Systems OY, Juurakkotie 3, 01510 VantaaFI

Puh: 09-274 697 0 Fax: 09-274 697 40 E-mail: inf[email protected] www.nibe.fi

NIBE Energy Systems France Sarl, Zone industrielle RD 28, Rue du Pou du Ciel, 01600 ReyrieuxFR

Tel : 04 74 00 92 92 Fax : 04 74 00 42 00 E-mail: [email protected] www.nibe.fr

NIBE Energy Systems Ltd, 3C Broom Business Park, Bridge Way, Chesterfield S41 9QGGB

Tel: 0845 095 1200 Fax: 0845 095 1201 E-mail: [email protected].uk www.nibe.co.uk

NIBE Energietechniek B.V., Postbus 634, NL 4900 AP OosterhoutNL

Tel: 0168 477722 Fax: 0168 476998 E-mail: [email protected] www.nibenl.nl

ABK AS, Brobekkveien 80, 0582 Oslo, Postadresse: Postboks 64 Vollebekk, 0516 OsloNO

Tel. sentralbord: +47 23 17 05 20 E-mail: [email protected] www.nibeenergysystems.no

NIBE-BIAWAR Sp. z o. o. Aleja Jana Pawła II 57, 15-703 BIAŁYSTOKPL

Tel: 085 662 84 90 Fax: 085 662 84 14 E-mail: sekretariat@biawar.com.pl www.biawar.com.pl

Tel./fax +7 831 419 57 06 E-mail: [email protected] www.nibe-evan.ru

NIBE AB Sweden, Box 14, Hannabadsvägen 5, SE-285 21 MarkarydSE

Tel: +46-(0)433-73 000 Fax: +46-(0)433-73 190 E-mail: [email protected] www.nibe.se

For countries not mention in this list, please contact Nibe Sweden or check www.nibe.eu for more information.

NIBE™ F135Chapter 1 | Important information4

Transport

F135 should be transported and stored vertically in a

dry place.

Assembly

■F135 is installed freestanding on brackets or a suit-

able flat surface. Noise from the circulation pump,

fan and compressor can be transferred to the brack-

ets or the surface that F135 is placed on. Use the

product's adjustable feet to obtain a horizontal and

stable set-up.

30 - 50 mm

15 - 40 mm

■F135 must be positioned with the back towards a

wall. Install the brackets or position F135 against an

outside wall, ideally in a room where noise does not

matter, in order to eliminate noise problems. If this

is not possible, avoid placing it against a wall behind

a bedroom or other room where noise may be a

problem.

■Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

■Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

Installation area

Leave a free space of 800 mm in front of the exhaust

air module. Approx. 50 mm free space is required on

each side, to remove the side panels. The panels do not

need to be removed during service, all service can be

carried out from the front. Leave space between the

exhaust air module and the wall behind (and any

routing of supply cables and pipes) to reduce the risk

of any vibration being propagated.

800

300

10-25

10-50* 10-50*

* Depending on whether the panels can be removed or not.

NOTE

Ensure that there is sufficient space (300 mm)

above F135 for installing ventilation hoses.

800

300

10-25

10-50* 10-50*

5Chapter 2 | Delivery and handlingNIBE™ F135

2 Delivery and handling

Supplied components

Location

The kit of supplied items is placed on top of the

product.

SilencerAir connection

LEK

Mora kniv

LEK

4-pin terminal blockFilter cartridge

LEK

567

425

Drain hose Ø 20 mm

L=2200 mm

2 x bracket

6 x screws

6 x nuts

4 x washers

NIBE™ F135Chapter 2 | Delivery and handling6

Removing the covers

Front hatch

LEK

1. Slacken off the screws for the securing plate above

F135.

2. Slide the hatch upwards and pull it towards you.

3. Pull the hatch towards yourself.

NOTE

A ground cable is installed in the hatch, it can

therefore only be lifted out 0.35 m. If the hatch

needs to be removed completely, the cable

must be detached.

Side panels

1. Undo the screws at the edge.

2. Twist the cover slightly outward.

3. Move the side cover outwards and backwards.

4. Assembly takes place in the reverse order.

LEK

7Chapter 2 | Delivery and handlingNIBE™ F135

LEK

QN1

BT76 GP12 PF1EB10

X11

GQ10

AA2

QM25

XL44

XL43

BT77

BT16

QN20

HZ2

EP2

BP1

BT13

XL9

EP1

GQ1

XL8

BT12

CA1

PF3

NIBE™ F135Chapter 3 | The exhaust air module design8

3 The exhaust air module design

Altri manuali per F135

Indice

Manuali Pompa di calore popolari di altre marche

MICROWELL

MICROWELL HP 1000 GREEN Manuale utente

Sanyo

Sanyo SAP120FCH Manuale utente

Daikin

Daikin EHYHBH05AA Manuale utente

Panasonic

Panasonic WH-SDF03E3E5 Guida

Bryant

Bryant 544B Manuale utente

Airxcel

Airxcel 45000 Series Manuale

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuale utente

Dimplex

Dimplex LI 16I-TUR Guida utente

Carrier

Carrier WSHP Open v3 Guida rapida alla configurazione

TGM

TGM CTV14CN018A Manuale utente

Carrier

Carrier 38MGQ Series Manuale utente

Kokido

Kokido K2O K880BX/EU Guida alla risoluzione dei problemi

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guida rapida

Carrier

Carrier 48EZN Manuale utente

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Istruzioni operative

Ariston

Ariston NIMBUS Manuale utente

Weishaupt

Weishaupt WWP L 7 Guida utente

GE Zoneline AZ85H09EAC Manuale utente