Nico Technology 1201L-1K RTD Manuale utente
1201L-1K RTD Controller User’s Manual
1 Rev.1.1
1201L-1K RTD Controller
Revision 1.1
Nico Technology Ltd.
24F,No.37,SanMin Rd, 2.Sec, PanChiao City, Taipei County, Taiwan
Phone +886-2-2954-5338
Fax +886-2-2954-5308
Technical Support Tom_Yeh@nico-tech.com
Web site http://www.nico-tech.com
1201L-1K RTD Controller User’s Manual
2 Rev.1.1
This Manual
This manual provides any required information for installation, configuration
and operation of the Nico Technology Ltd.1201L-1K RTD Controller.
It exclusively treats the handling of this device. It neither describes the
LonWorks technology by Echelon nor the LonMark profile implemented in
detail. More specific information concerning these subjects can be found in the
documentation of Echelon (www.echelon.com) and the LonMark
Interoperability Association (www.lonmark.org).
The first part of this manual provides a survey about the device and its
installation in chapters 1 to 3. The 2nd part describes the implemented
application for lighting control and its configuration possibilities. Chapter 4
contains a description of the firmware interface while chapter 5 describes the
implemented LonMark Objects in detail providing an outlook of the individual
objects, their tasks and their relevant configuration parameters.
Chapter 6 explains the basics required to connect the objects to each other.
This manual is relevant for all variants of the Nico Technology Ltd.1201L-1K
RTD Controller where applications for building automation control are
implemented.
This documentation is subject to modification at any time without prior advice. Nico does not take over any
responsibility for mistakes or inaccuracies in this documentation and eventually occurring consequences.
In any case Nico as well as its representatives and staff are not reliable for eventual defaults, damages caused
indirectly or during use, occurring due to the use or non-usability of the software or the accompanying documentation.
Nico is a registered trademark of Nico Technology Ltd.
Echelon, LON, LonMark, LonWorks and Neuron are registered trademarks of Echelon Corporation. Other name may
be registered trade marks of the respective companies.
1201L-1K RTD Controller User’s Manual
3 Rev.1.1
Contents
Contents .........................................................................................................................3
2 Product Information...............................................................................................4
2.1 Functional Elements...................................................................................4
3 Installation..............................................................................................................5
3.1 Warnings ....................................................................................................5
3.2 Mounting....................................................................................................6
3.3 Connections................................................................................................6
3.4 Software Installation..................................................................................7
4 Device Description.................................................................................................8
4.1 Hardware Survey .......................................................................................8
4.2 Operation and Display Elements ...............................................................8
4.3 Connection Pin Assignment.......................................................................8
4.4 Wiring Diagram .......................................................................................11
4.5 EMC.........................................................................................................12
4.6 Technical Specifications ..........................................................................13
4.7 Dimensions ..............................................................................................14
5 Application Software for Building Automation Control .....................................15
5.1 System Scope...........................................................................................15
5.2 Interoperable Interface.............................................................................15
6 System Objects.....................................................................................................16
6.1 Node Object.............................................................................................16
6.2 Temp Sensor (OLS) Object......................................................................17
1201L-1K RTD Controller User’s Manual
4 Rev.1.1
2 Product Information
2.1 Functional Elements
Figure 1.1 1201L-1K RTD Controller
No Description
1 Power Indicator
2 Service Pin LED indicator
3 Transmission LED indicator
4 Receive LED indicator
5 Reset button
6 Service Pin button
7 Pt1000 Sensor Probe
8 12~24VDC Input Power
9 LonWorks FTT-10 Channel
1201L-1K RTD Controller User’s Manual
5 Rev.1.1
3 Installation
This chapter first describes the installation of the device; the installation of the
configuration software is described in section 3.4.
3.1 Warnings
Attention
The device must be installed in compliance with the relevant DIN/VDE
regulations or the relevant national standards. The connection to the
supply voltage must be performed in accordance with VDE 0100 and VDE
0160 or the relevant national standard Installation should perform by
qualified and technical experienced personnel only.
CAUTION
At the connections of the input channel (Fig. 1.1, terminal 7) and the power
supply (terminals 8) 12~24VDC main voltage with load guard band is
accessible. The installation of the unit therefore has to be effected in a
switch cabinet or behind a respective cover.
1201L-1K RTD Controller User’s Manual
6 Rev.1.1
3.2 Mounting
3.3 Connections
The1201L-1K RTD Controller has to be connected to a 12~ 24VDC power
supply and to the LonWorks network.According to the respective
application peripheral equipment has to be connected to outputs.
1201L-1K RTD Controller User’s Manual
7 Rev.1.1
Attention
Before connecting peripheral equipment the power supply device has to be
switched off.
The connection is effected by means of the included plug-screw terminals.
Clamping range of the plug-screw terminals:
- DC power and network connections (terminals 8): 2.5 mm
The pin assignment of the connections is described in chapter 3.1, also
containing wiring details.
Voltage
The 12~24 Volt Direct Current connections are through connected in order to
achieve easy wiring.
LonWorks Network
The connection to the LonWorks network is made by means of twisted-pair
cables. The connection “shield” has to be connected to ground in order to
achieve a reliable dissipation of over-voltage on the LON circuits.
Analog Inputs
The actors to be controlled are connected to the RTD Pt1000 inputs. In each
case the connection is effected terminal 1).
Attention
The 1201L-1K RTD Controller input power supply must within 12~ 24VDC
power supply only.
3.4 Software Installation
The configuration software of the 1201L-1K RTD Controller has to be
installed by starting the program Setup.exe on the data carrier provided. It
suns under Windows 9x/2000 and NT.
Download url: http://www.nico-tech.com/download
1201L-1K RTD Controller User’s Manual
8 Rev.1.1
4 Device Description
The 1201L-1K RTD Controller for LonWorks network in building automation. Its
peripheral scope has been specially designed for the use as temperature or
humidity sensor device spreading control of applications such as valve control
or lighting control thru Lux sensor.
For the use in building automation control the1201L-1K RTD Controller
realizes 1 independent input channel.
The LonMark object available per channel flexible use of the 1201L-1K RTD
Controller; The configuration of the building automation application is effected
via any LonWorks network management tool.
Of course, the1201L-1K RTD Controller is also freeing programmable in
Neuron C. As a flash module is used the application can be load via the
LonWorks network, making the 1201L-1K RTD Controller, e.g. for detail info
4.1 Hardware Survey
The1201L-1K RTD Controller disposes of eight output circuit for each. The
output circuit can be accept individually input RTD Pt1000 single.
4.2 Operation and Display Elements
The1201L-1K RTD Controller is fitted with a service button accessible via
a small gap on the front panel (see Figure. 1.1, 6).Activation of the buttons
generates a service-pin message transmitted via the LonWorks network.
The processor status as well as the service-pin status are displayed by the
service LED (figure. 1.1,2), which is on while the service button is activated.
By use the network management function Wink the service LED flashes.
Furthermore the1201L-1K RTD Controller is fitted with a reset LED (figure.
1.1, 1) same as Power indicator, displaying the availability of device occur
reset. The LED is connection to an I/O pin of the Neuron chip processor.
4.3 Connection Pin Assignment
The following tables show the connector pin assignment of the individual
connectors. Connections the 1marking cf. Figure. 1.1 On previously page.
In each clamp block pin 1 is situated on the left. For further wiring
1201L-1K RTD Controller User’s Manual
9 Rev.1.1
information see figure 3.2.
LonWorks Network Connection
The double-core bus line can be connection either to LON Aor to LON B.
No polarity has to be considered by connecting the LonWorks network.
Figure 3.1 Connector pin assignment LonWorks network
1201L-1K RTD Controller User’s Manual
10 Rev.1.1
Input circuit
Figure 3.2 Connector pin assignment input circuit.
Power Supply
The1201L-1K RTD Controller has to be connected via connector 2, 3, 5, 7
to 24VDC main voltage. Also see figure. 1.1.
Figure 3.3 Connector pin for Power Supply near LonWorks channels side
Indice
Altri manuali Nico Technology Controllori
