Nikon D60 Istruzioni operative
作成承認印 配布許可印
VBA21001-R.3753.A
Printed in Japan Feb 2008
VBA21001
Copyright© 2008 by NIKON CORPORATION.
All Rights Reserved.
無断転載を禁ず！！
logo_Q0650_forGraphic
071004_Gdesign_ito
Ｍ
サービス
計画課
REPAIR MANUAL
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
Points to notice for Disassembly / Assembly
㧍
内部に高電圧部あり。カバーを外す時は感電に注意すること。
カバーを外した後は、修理指針の指示に従ってメインコンデン
サーの放電を必ず行うこと。
警告
Caution:
Whenever "Separation of Front and rear bodies", "Disassembly of CCD/FPC unit", or
"Disassembly of Bayonet" are performed, be sure to perform "RESETAF-DEFOCUS
COMPENSATION" of camera adjustment software after reassembling.
WARNING
Due to an internal high voltage area, take extra care not to get
an electric shock when detaching covers.
After removing covers, besure to discharge the main
condenser according to the instructions of repair manuals.
Note:
① When disassembling/(re)assembling, be sure to use the conductive mat (J5033) and wrist strap (J5033-5)
for static protection of electrical parts.
② Before disassembling, be sure to remove batteries or AC power wires.
③ When disassembling, make sure to memorize the processing state of wires and FPC, screws to be xed
and their types, etc.
④ Because the low pass lter of the imaging CCD PCB is easily damaged, handle it with enough care.
Points to notice for Lead-free solder products
・ Lead-free solder is used for this product.
・ For soldering work, the special solder and soldering iron are required.
・ Do NOT mix up lead-free solder with traditional solder.
・ Use the special soldering iron respectively for lead-free solder and lead solder.
They cannot be used in common.
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
#5735
Bottom cover
#5674×2
#5735
#5674
#5674
#5735×2
#5674
Power-wire lid
・Take out the four screws (#5735)
and ve screws (#5674).
・Open the power-wire lid.Open the power-wire lid.
・Remove the bottom cover.
Disassembly
1. Separation of Front and Rear Bodies
Bottom Cover
・Take out the four screws (#6690) and two screws (#5618).
・Remove the rear cover.
・Remove the rear FPC from the connector.
Rear cover
Note: Remove the rear cover slowly so as not to cut the rear FPC
of the lower portion of the cover.
#5618×2
Rear FPC
#6690×4
Rear cover
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
Rear cover
A
A
#408
#402 #403
#5418
#5412
#448
#753
#423
#5429
#1037
#405×2
#404×2
#426-1
#425-2×2 #421
#5427
#5426
#5425
#5424
#670×3
#B5431
#5431
#5681×2
#433
#5432
#407
#630×3
#750
#406-2
#410
#409-1
#1017
#414
#413
#453
#452
#451×2
#1016
#6401-3
Ｍ
サービス
計画課
Mar.19.2008
Changed page △×１
△(Addition)
Remove the only below parts
of thermal caulking.
Mold #426-1
Caulked portions
LCD-monitor retainer plate
Remove
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
Approx. 2cm
Approx. 4cm
SB pop-up
・Cut the tracing lm sheet, etc into the below size of piece.
Then insert it into the clearance of the top cover pop-up
part as shown right, and raise the SB by sliding the sheet in
the direction of the arrow.
㧍
内部に高電圧部あり。カバーを外す時は感電に注意すること。
カバーを外した後は、修理指針の指示に従ってメインコンデン
サーの放電を必ず行うこと。
警告
WARNING
Due to an internal high voltage area, take extra care not to get an
electric shock when detaching covers.
After removing the covers, be sure to discharge the main
condenser according to the instructions of repar manuals.
Covers
#5610×2
#5610×2
#29
#26
#131
#5120
#670
#792C
#626
#750×2
#B24
#6074
Adhesive: Super X
Adhesive: AlonAlfa
(Quick drying glue)
Adhesive: Super X
・Take out the four screws (#5610) and
the screw (#626).
・Remove the front cover unit (#B24) and
[#131].
(Be careful not to drop [#131].)
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
TOGO PCB unit / Loft PCB
・Disconnect the six FPCs and harness from the connector.
・Unsolder the six wires.
・ Take out the ve screws (#663).
Be careful so that the top cover does NOT touch the
discharge tool.
Discharge of Main condenser
・Discharge the main condenser from its both ends.
Main
condenser
2KΩ/5W
Uncoated
Blue: Backup battery
Coated
Pink: Relay-PCB
Uncoated
Coated
#663×5
TA-0025
(5×8)
#483
#1053
TOGO PCB (#B2001)
Harness
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
#B3051
#631×3
Red: Backup battery
Yellow:DC/DC
Blue:DC/DC
Red:DC/DC
Purple:DC/DC
Green:DC/DC
Adhesive double-coated tape
(attached on back of loft-PCB
Loft-PCB
(#1031)
Gray: Buzzer unit
Gray: Buzzer unit
TOGO-PCB unit (#B2001)
(The other side)
・Disconnect the TOGO-PCB unit (#B2001) from the connector, (while pressing the loft-PCB).
・Disconnect the two FPCs from each connector.
・Unsolder the eight wires.
・Remove the loft-PCB that is partially attached with the adhesive double-coated tape.
Caution:
Some bodies have already washer(s) attached on the
mounting surface of CCD unit.
・Take out the three screws (#631), and remove the CCD unit (#B3051).
CCD unit
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
・
Unsolder the four wires (connected
from Top cover).
SB PCB
Orange: Top cover
White: Top cover
Gray: Top cover
Black: Top cover
・Unsolder the wire (connected from Top cover).
DC/DC PCB unit
Top cover
・Take out the two screws (#5737).
・Take out the two screws (#635).
・The top cover and rubber eyecap (#B271)
come off.
Black: Top cover
#B271
#5737×2
#635×2
#486×2
#487×2
AUTO
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
#632×2
SB upper case (#5301)
Claw
Pop-up lever A part
・ Press "Pop-up lever A part" and raise the built-in SB.
Disassembly of Top cover
SB upper case
・ Take out two screws (#632).
・Release the two claws. House the built-in SB and remove the SB upper case (#5301).
INC
- Ｄ･ -
logo_Q0650_forGraphic
071004_Gdesign_ito
VBA21001-R.3753.A
・Remove the tape (#956).
・Unsolder the seven wires (connected from SB lower case unit and SB release base unit).
・Remove the ve solder bridges.
Top cover FPC / Wiring
Red: SB release base unit
Black: SB release base unit
#956
Red: SB lower case unit
Blue: SB lower case unit
Green: SB lower case unit
Black: SB lower case unit
Black: DC/DC PCB
・Remove the two wires (black and uncoated) (connected from AF-assist illuminator unit).
・Take out the screw (#608), and remove the AF-assist illuminator unit (#B325).
AF-assist illuminator unit
#608
AF-assist illuminator unit (#B325)
Black: AF-assist illuminator unit:
Uncoated wire: AF-assist illuminator unit
INC
Altri manuali per D60
9
Indice
Altri manuali Nikon Macchina fotografica digitale
Nikon
Nikon CoolPix P80 Manuale del proprietario
Nikon
Nikon COOLPIX S3500 Manuale utente
Nikon
Nikon D3300 Manuale utente
Nikon
Nikon D3 Manuale utente
Nikon
Nikon CoolPix S570 Manuale utente
Nikon
Nikon COOLPIX S4000 Guida utente
Nikon
Nikon COOLPIX 5400 Manuale utente
Nikon
Nikon S5100 Manuale utente
Nikon
Nikon CoolPix S710 Manuale del proprietario
Nikon
Nikon CoolPix S70 Manuale utente
Nikon
Nikon D5500 Manuale utente
Nikon
Nikon Coolpix P5000 Manuale utente
Nikon
Nikon Z 6II Manuale utente
Nikon
Nikon COOLPIX L28 Manuale utente
Nikon
Nikon D90 - Digital Camera SLR Manuale utente
Nikon
Nikon COOLPIX L610 Manuale utente
Nikon
Nikon D80 VBA14001 Istruzioni operative
Nikon
Nikon COOLPIX L820 Manuale utente
Nikon
Nikon Coolpix L31 Manuale utente
Nikon
Nikon EM Manuale utente
