Niles RCA2 Istruzioni operative originali

Remote Control

Anywhere!™Kit

BLENDING HIGH FIDELITY AND ARCHITECTURE®

INSTALLATION & OPERATION GUIDE

Remote Control

Anywhere!™Kit

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 24

TABLE OF CONTENTS

Introduction 2

Getting

Started 4

Installation 4

System

Operation 13

Optional

Accessories 14

Running Sensor

Cable in New

Construction 16

Concealing

Sensor Cable

in Existing

Walls 18

Specifications 22

EMOTE

ONTROL

NYWHERE

! K

RCA2

Remote Control

Anywhere! Kit

WARNING – To prevent possible injury, the

following basic safety precautions should be

observed in the installation and use of your

Remote Control Anywhere Kit.

1. Read through the entire manual – Before attempting

any installation, read this manual thoroughly and keep it for

future reference.

2. Avoid contact with all high voltage electrical wiring

and equipment!

3. Keep away from water and moisture – Never use or

install electronic products near water, ie., near a bathtub,

sink, washing machine, in a wet basement, near a swim-

ming pool, or anywhere else the product may be exposed

to water or moisture.

4. Power supply cord protection – Do not run the power

cord where it may be subject to wear or abuse. Do not

allow anything to rest on or roll over the power cord which

may damage it.

6. Lightning – It is suggested that you remove the power

supply from the wall if your system will not be used for long

periods of time. Power surges due to lightning strikes may

damage your equipment.

7. Check your local building and electrical codes –

There may be specific requirements regarding running low

voltage in your area.

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 1

EMOTE

ONTROL

NYWHERE

! K

Introduction

The Remote Control Anywhere! Kit

enables you to operate your remote con-

trolled audio/video equipment from vir-

tually any location. Now you can place

your audio/video (A/V) components out

of sight (behind cabinet doors, in the rear

of a room, or in a different room) and still

conveniently control your system.

Kit Contents

Check that your Remote Control

Anywhere! Kit contains the following:

• Connection hub

• Table-top sensor

•12VDC power supply

• MicroFlashers (3)

• Category 5 sensor cable (50')

Connection Hub Table-Top Sensor

MicroFlashers (3)

Category 5 sensor

Cable (50ft)

12VDC Power Supply

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 2

EMOTE

ONTROL

NYWHERE

! K

Tools Needed

• Pencil

• Drywall saw

• Standard screwdriver

• Phillips screwdriver

• Wire strippers

• Drill (and assorted bits)

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 3

Getting Started

While the Remote Control Anywhere! Kit is compatible

with most brands of audio/video components, there are

a few exceptions. You should perform

a temporary hook-up to test for compatibility before you

conceal wire or permanently mount any parts.

Steps One through Five describe how to perform a

quick and easy check for compatibility.

Once you have determined that all of your remote

controlled A/V components are compatible,

proceed with the rest of the installation.

Installation

Step 1 – Placing the Connection Hub

Place the Connection Hub so that the MicroFlasher wires

will reach the components.

Never place the connection hub closer than

1' away from a television set (Figure 1).

EMOTE

ONTROL

NYWHERE

! K

Figure 1: Connection

Hub Placement

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 4

EMOTE

ONTROL

NYWHERE

! K

Step 2 – Connecting the Sensor Cable to the

Connection Hub

For your convenience, the sensor cable ends have

been stripped.

Insert each wire into the appropriate hole on the removable

connector plug (Figure 2), and snap the locking tab down.

To help you, the connector plug is keyed. Insert the smooth

side of the connector plug into the smooth side of the socket.

Don’t force the scalloped side of the connector plug into the

smooth side of the socket.

1234

POWER

+12V DC

3-30V

AC/DC

STATUS

FLASHER OUTPUTS

MSU140

IR MAIN SYSTEM UNIT

INPUT 1

TS100 Sensor

To unswitched

AC Outlet

Figure 2:

MSU140

Installation

MSU140 Sensor

Connection

MSU140

To Niles

IR Flasher To 12VDC Power Supply

Plugged into an switched AC Outlet.

Typically found in back of a receiver.

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 5

Step 3 – Connecting the Sensor Cable to the

Table-Top Sensor

Pull out the removable connector from the bottom of the

table-top sensor. Insert each wire into the appropriate hole on

the removable connector plug (Figure 3), and snap the lock-

ing tab down. To help you, the connector plug is keyed. Insert

the smooth side of the connector plug into the smooth side of

the socket. Don’t force the scalloped side of the connector

plug into the smooth side of the socket.

Make sure that the orientation of the connector is correct

(Figure 4).

EMOTE

ONTROL

NYWHERE

! K

Figure 3: Removable

Connector Plug

1 = Green/White - 12V

2 = Green - DATA

3 = Orange/White - GROUND

4 = Blue - EMPTY

5 = Blue/White - STATUS

6 = Orange - EMPTY

7 = Brown/White - EMPTY

8 = Brown - EMPTY

1 = STATUS

4 = 12V DC

1 = 12V

2 = DATA

5 = STATUS

3 = GROUND

2 = DATA 3 = GROUND

Tab

Down

Figure 4: Installing

Sensor Connector

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 6

EMOTE

ONTROL

NYWHERE

! K

Additional

Flashers

REMOTE CONTROL ANYWHERE!

CONNECTION HUB

Additional

Flashers

REMOTE CONTROL ANYWHERE!

CONNECTION HUB

Figure 5:

Connection Ports

Step 4 – Connecting the 12VDC In-Line Power Supply

and MicroFlashers

Plug the MicroFlashers into any of the sockets labeled FLASHER

OUTPUTS on the connection hub (Figure 5).

Plug the connector on the supplied 12VDC power supply into

the socket labeled POWER on the connection hub and then

plug the wall adapter into a live electrical outlet. The power

LED should light.

If the LED does not light, confirm that the outlet you used is

live by plugging in a lamp.

“TECH TIP”

Wire size is expressed

by it’s AWG (American

Wire Gauge) number.

The lower the AWG

number, the larger

the wire, i.e., 20 AWG

wire is physically larger

than 22 AWG.

“TECH TIP”

Make all final connec-

tions to the MSU

before connecting the

power supply. This will

avoid potential dam-

age to components.

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 7

EMOTE

ONTROL

NYWHERE

! K

Step 5 – Mounting a MicroFlasher to A/V Components

Make sure all of your remote controls have batteries and that

they are able to operate the A/V components.

Locate a place for the remote control that is within arm’s

length of the A/V components, yet cannot directly control

them. Place the table-top sensor no closer than two feet in

front of the remote control (Figure 6).

Hold the MicroFlasher four inches

in front of the remote sensor

window on the A/V compo-

nent’s front panel. Press but-

tons on the remote control

while watching the front

panel of the A/V compo-

nent. When the compo-

nent responds repeatedly

to the commands, peel off

the protective backing on

the MicroFlasher and place

the MicroFlasher in that

location.

If the A/V component’s

remote sensor is not clearly

marked, slowly move the

MicroFlasher over the win-

dow of the A/V component

while pushing buttons on

the remote control until you

get a response (Figure 7).

Figure 6:

Locating IR Sensor

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 8

EMOTE

ONTROL

NYWHERE

! K

Repeat this procedure for each A/V component

you wish to control.

When the A/V component responds repeatedly,

peel off the protective backing on the

MicroFlasher and place the MicroFlasher in that

location.

If you get no response at all, call Niles Technical

Support at 1-800-289-4434 (M-F 8:00 AM –

7:00 PM ET).

Step 6 – Mounting the Connection Hub

Make sure that your system tested OK before

proceeding

Once you have decided on the ideal location for

the connection hub, unplug the 12VDC power

supply from the electrical outlet and disconnect the sensor and

the MicroFlasher cables from the connection hub (Figure 8).

Also remove the connector from the table-top sensor (Figure 9).

The connection hub can be either mounted on a wall using

screws or placed on a shelf using the included adhesive feet

(Figure 10).

Figure 7: Locating IR Sensor

DS00224CCN_RCA2 Kit.qxp 6/22/04 3:28 PM Page 9

Altri manuali per RCA2

Indice

Altri manuali Niles Telecomando

Niles

Niles RCA-HT2 Manuale utente

Niles

Niles iREMOTE Manuale utente

Niles

Niles iREMOTE TS Manuale utente

Niles

Niles Remote Control Anywhere Kit Manuale utente

Niles

Niles VCS50R Guida alla risoluzione dei problemi

Niles

Niles RCA-TT Manuale utente

Niles

Niles RCA-SM2 Manuale utente

Niles

Niles HR200 Manuale utente

Niles

Niles EVC-100 Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

Niles

Niles VCS-2D Istruzioni operative originali

Niles

Niles RCA-TT Manuale utente

Niles

Niles ZR-6 Istruzioni operative originali

Niles

Niles VCS-2S Manuale utente

Niles

Niles INTELLIPAD CI Manuale utente

Niles

Niles IntelliPad Manuale utente

Niles

Niles REMOTE CONTROL ANYWHERE! RCA-TT2 Manuale utente

Niles

Niles RCA-HT Manuale utente

Niles

Niles iREMOTE TS Manuale utente

Niles

Niles SVC100R Manuale utente

Niles

Niles RCA-SM Manuale utente

Niles

Niles TVC-1 Istruzioni operative originali

Niles

Niles R-6L Istruzioni operative originali

Niles

Niles RCA-HT2 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione

Invacare

Invacare G91S Manuale utente