Nilfisk-Advance Compact Vac A Manuale utente

Nilfisk Compact Vac A

Compressed Air Vacuum

Specifications

Minimum Compressor Required h.p. 20

Air Hose Diameter inches ½

Input Supply Air psi 90

Input Supply Air cfm 70

Maximum Output Airflow cfm 140

Maximum Waterlift at Control Pressure inches 172

Air Performance air watts 392

Tank Capacity gallons dry bulk 1

Paper Bag Capacity gallons dry bulk 1

Filter Area square inches 1151

Dimensions (L x W x H) inches 23 x 15½ x 22

Container Diameter inches 10.5

Weight with Back Pack lbs. 14

Sound Level dB(A) at 6’6” 77

NILFISK-ADVANCE AMERICA, INC., 300 Technology Drive, Malvern, PA 19355, 1-800-645-3475, www.pa.nilfisk-advance.com

Instructions for Use

Nilfisk Compact Vac A

Compressed Air Vacuum

WARNING: This Nilfisk vacuum cleaner or any other vacuum

cleaner is not to be used in explosion-hazardous areas, as serious

injury could result.

Under no circumstances may this cleaner be used safely for the collection of hazardous or toxic

materials unless equipped with special HEPA* filters and bags which have been installed according to

written instructions from Nilfisk-Advance.

ATTENTION EMPLOYER: Please ensure these Instructions for Use are made available and

understood by your employees or any other persons who use this equipment.

To list all toxic and hazardous materials would be beyond the scope of these instructions. It is the

Employer's responsibility to identify, for Employee's and others' information, hazardous or toxic

materials which may be collected by this equipment. Such information must be communicated to your

Employees and other potential users of this equipment.

Your new Nilfisk industrial vacuum cleaner is a precision-engineered instrument designed for

exceptionally fine filtration. Ordinary vacuum cleaners do not have HEPA filters and cannot be used

safely for hazardous dusts. This Nilfisk machine is safe to use as a dust collector for finely ground

materials, as long as certain precautions are taken. Proper care of this cleaner is essential to the

maintenance of its ultrafine filtering capabilities.

BEFORE USE: DO NOT ATTEMPT TO OPERATE THIS CLEANER UNTIL YOU HAVE INSTALLED

ITS VARIOUS COMPONENTS ACCORDING TO THE FOLLOWING INSTRUCTIONS.

MACHINE SET-UP

1. Remove vacuum from backpack frame by removing the two (2) pull pins located behind the

vacuum container and release the air supply quick coupler.

2. Installing the Polyliner and Paper Bag:

A. Unclamp the two container clips located on the body of the

container.

B. Lift off the venturi assembly.

C. Open the polyliner and place it in the bottom of the container

flush against the container sides and lipped under the container inlet (Photo 1).

D. Drape the excess length of polyliner over the top of the container and down the outside, then

roll the edge to permit the container to close.

*HEPA-High Efficiency Particulate Air – Retains 99.97% of particles to 0.3 microns in size.

Install a paper bag inside the polyliner by expanding the folds of the bag and piercing the

perforations within the bag inlet collar. Then slide the round paper bag collar opening over the

plastic inlet tube of the vacuum orifice.

3. Installing the Microfilter:

A. Slide microfilter (#61682100) over the HEPA filter making sure to pull it up as far as it will go,

covering the HEPA housing completely.

B. Secure with metal clamp band around the filter and tighten (Photos 2 & 3). NOTE: Make sure

the metal band seats firmly against the venturi plate.

C. Clamp venturi assembly back onto the container and close the clips.

D. Connect the vacuum to the back frame.

a. Fit the two protruding bolts on the back of the machine into the holes in the curved metal

plates on the back frame (Photo 4).

b. Lock the back frame in place by inserting each of the safety pegs (pull rings suspended on

cords from the back frame) into the holes in the bolts on the Compact Vac A (Photo 5).

Then connect the air supply quick coupler.

c. The back frame’s shoulder straps can be adjusted to operator size by pulling or loosening

the lower straps through the buckles. Also provided for proper balance is a waist strap that

is pulled around the operator and buckled in front.

4. Abrasive Tool Set-up

A. Connect 1 ½” diameter hose to the vacuum by twisting the coupler (#01782600) into the

vacuum orifice clockwise.

B. Connect the 4.5” sander/grinder, 5’ long needle gun or pistol grip needle gun to the opposite

end of the hose by sliding the coupler (#01716500) over the 1 ½” diameter vacuum take off on

the tool shroud. Slide the plastic hose with cuff onto the inlet coupler.

C. Turn vacuum on by opening the air valve before using abrasive tool.

5. Cleaning Accessories Set-up

A. Connect the tapered hose (#12097500) to the vacuum by twisting the coupler into the vacuum

orifice clockwise.

B. Connect any of the cleaning accessories to the opposite end of the hose by sliding the

accessory over the metal tube at the end of the hose.

EMPTYING

WARNING: IF THIS VACUUM CLEANER IS USED TO COLLECT HAZARDOUS MATERIAL, DO

NOT ATTEMPT TO OPEN OR EMPTY ITS CONTENTS WITHOUT PERSONAL PROTECTIVE

CLOTHING AND RESPIRATORY PROTECTION.

1. To empty the container and its contents, first turn off the venturi.

2. Allow the cleaner to sit undisturbed for at least thirty (30) seconds.

3. Remove vacuum from back frame by removing the two pull pins located behind the vacuum

container.

4. Unclamp the container clips located on the body of the container.

5. Turn on the venturi once the seal is broke and lift off the venturi assembly with the HEPA filter

spacer.

6. Gently slide the round paper bag collar opening off of the plastic inlet tube of the vacuum orifice.

7. Pull the polyliner around the paper bag and seal off the polyliner with the paper bag inside.

8. Install a new polyliner and paper bag according to the previous instructions (Machine Set-up,

Step 2).

FILTER REPLACEMENT

To ensure that your Nilfisk cleaner delivers the years of trouble-free operation for which it was

designed, it is necessary to check and replace filters regularly.

The internal microfilter and HEPA filter of the Compact Vac A are located directly under the venturi

housing.

1. Microfilter: This small white sock, which fits over the HEPA filter spacer, will require periodic

inspection. Dust will discolor the white microfilter. Change the microfilter as soon as any

discoloration is easily noticable.

A. Loosen the metal clamp band with a screw driver and pull the microfilter off the HEPA filter

housing.

B. Pull the new one on, making sure to pull it up as far as it will go, covering the HEPA housing

completely.

C. Replace the metal band around the filter and tighten. NOTE: Make sure the metal band seats

firmly against the underside of the venturi assembly. WARNING: Do not shake the microfilter,

since this can cause liberation of potentially harmful microscopic dust into the air. Do not

launder the microfilter. Remove carefully and discard with the collected debris in the sealable

poly bag.

2. Internal HEPA Cartridge: The vacuum’s internal HEPA filter should be changed approximately

every fourth time the microfilter is changed. Exact life will depend upon application, frequency of

use and prefilter maintenance.

Every Nilfisk replacement filter (#017276-31) (Photo 6) comes

with a new foam rubber sealing gasket.

Installing the internal filter cartridge:

A. Remove the microfilter by loosening its metal band and

pulling it off like a sock. You will now see the cartridge in its

cage-like holder (Photo 2).

B. To remove the cartridge, loosen and remove the four (4) wing nuts from beneath the holder.

C. Pull the metal plate free of the four pegs and carefully remove the filter.

D. Also remove the foam gasket. Discard both items and the microfilter with the collected debris

in a sealable poly bag.

E. To install the new filter, place the new gasket in the recess of the filter holder.

F. Then install the HEPA cartridge label side out in the holder.

G. Replace the metal plate and secure it with the wing nuts. NOTE: Make sure the wing nuts are

well tightened to provide the necessary seal. When tightening the wing nuts, make sure that

the nuts on the underside of the filter mounting plate do not get caught on the filter end cap.

Do not over tighten.

H. Replace the black rings that cover the tabs of the wing nuts. The clearance between the

bottom filter end cap and the base of the filter mounting plate should be 5/32”.

I. Install a new microfilter (see instructions above), polyliner and paper bag, then assemble the

container.

WARNING: Use only genuine NILFISK replacement filter components. The use of substitute

components could pose a grave risk of personal exposure, and will cause all equipment

warranties to be void.

Compact Vac A

Accessories

3” Round Brush

112769-01

HEPA Replacement Cartridge

017276-31

Rubber Nozzle

81140900

Standard Microfilter

61682100

3 in 1 Floor Nozzle

11450201

Polyliners (25/pkg.)

01719000

6’6” Plastic Hose

12097500

Paper Bags (5/pkg.)

81620000

Straight tube 22” (each)

11112400

017196-15 81813800 017196-15 017826-00

Cuff Hose Cuff Coupler

Abrasive Tool Hose Assembly

WARRANTY

The Nilfisk companies warrant that Nilfisk equipment will be free of defects in workmanship or

material for a period of two years from the date of delivery. Should any failure to conform to this

warranty appear, the Nilfisk companies shall upon notification within such time period, correct

such non-conformity, at its option, either by repairing any defective part or parts, or by replacing a

part or parts provided that the equipment is returned to an authorized Nilfisk service facility. In all

cases freight both ways will be at the expense of the customer. Equipment shall not be returned

without advance notice to, and consent of the Nilfisk companies.

EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THE NILFISK COMPANIES MAKE NO

WARRANTIES, EITHER EXPRESSED OR IMPLIED AS TO ANY MATTER WHATSOEVER,

INCLUDING WITHOUT LIMITATION ANY AND ALL WARRANTIES OF MERCHANTABILITY,

FITNESS FOR PURPOSE, OR OTHER WARRANTIES, ALL OF WHICH ARE EXPRESSLY

DISCLAIMED AND EXCLUDED. NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT

LIMITED TO LOSS OF PRODUCTION, LOSS OF TIME, LOSS OF PROFITS OR OTHER

SIMILAR INDIRECT LOSSES WHICH MIGHT OCCUR AS A RESULT OF DEFECTS, PARTIAL

OR TOTAL FAILURE OF THE PRODUCT TO PERFORM AS SPECIFIED.

Correction of non-conformities or defects in the manner and for the period of time provided above,

shall constitute fulfillment of all liabilities of the Nilfisk companies to the customer, whether based

on contract, negligence or otherwise with respect to, or arising out of such equipment. The

remedies set forth herein are exclusive, and the liability of the Nilfisk companies with respect to

this sale or anything done in connection therewith, whether in contract, in tort, under any warranty,

or otherwise, shall not except as expressly provided herein, exceed the price of the equipment or

part on which such liability is based.

The warranty does not cover repairs due to normal wear and tear, accident, neglect, misuse or

abuse, incorrect installation or use other than as described in the instruction booklet. Breaks in

hoses and cables are not covered. This warranty is rendered void if the motor number plate is

removed or defaced or if repairs are made or attempted by persons not authorized by the Nilfisk

companies.

Indice

Altri manuali Nilfisk-Advance Aspirapolvere

Nilfisk-Advance

Nilfisk-Advance Buddy II Series Manuale utente

Nilfisk-Advance

Nilfisk-Advance S2 L Manuale utente

Nilfisk-Advance

Nilfisk-Advance 35 Manuale utente

Nilfisk-Advance

Nilfisk-Advance ID 2050 Manuale utente

Nilfisk-Advance

Nilfisk-Advance METEOR Manuale utente

Nilfisk-Advance

Nilfisk-Advance VHS110N1 CR Manuale utente

Nilfisk-Advance

Nilfisk-Advance VP600 Istruzioni operative

Nilfisk-Advance

Nilfisk-Advance Vacuum Cleaner Manuale utente

Nilfisk-Advance

Nilfisk-Advance CFM WSS 100 Manuale

Nilfisk-Advance

Nilfisk-Advance VU500 12 EU Manuale utente

Nilfisk-Advance

Nilfisk-Advance VP300 SERIES Manuale utente

Nilfisk-Advance

Nilfisk-Advance GD 110 Manuale utente

Nilfisk-Advance

Nilfisk-Advance AERO 26-01 X Manuale utente

Nilfisk-Advance

Nilfisk-Advance GM 80 Manuale utente

Nilfisk-Advance

Nilfisk-Advance Multi 20 Manuale utente

Nilfisk-Advance

Nilfisk-Advance 118EXP Manuale utente

Nilfisk-Advance

Nilfisk-Advance VP600 Manuale utente

Nilfisk-Advance

Nilfisk-Advance 56315044(855) Manuale utente

Nilfisk-Advance

Nilfisk-Advance Elite Manuale utente

Nilfisk-Advance

Nilfisk-Advance Supreme 100 Manuale utente

Nilfisk-Advance

Nilfisk-Advance VT 60 Wet/Dry Manuale utente

Nilfisk-Advance

Nilfisk-Advance IQ 215 Manuale utente

Nilfisk-Advance

Nilfisk-Advance GD 2000 Series Manuale utente

Nilfisk-Advance

Nilfisk-Advance Alto Filtra Vac 14 Manuale utente

Manuali Aspirapolvere popolari di altre marche

Bissell

Bissell LittleGreen Proheat 1425 Series Manuale utente

Panasonic

Panasonic MC-YL637S147-AE Manuale utente

NEFF

NEFF N17XH10 0 Series Manuale utente

LG A9 Series Manuale utente

Oreck

Oreck Cordless Captura BK51700 Series Manuale utente

Kogan

Kogan KAVACROBVWA Manuale utente

Kränzle

Kränzle VENTOS 50 ID Guida utente

EVVO

EVVO Ai35 Manuale utente

DeWalt

DeWalt DWH200D Manuale utente

Pontec

Pontec Pondomatic Vacuum Cleaner Manuale utente

Cleanmaxx

Cleanmaxx PC-P007E Manuale utente

Exido

Exido 240-114 Manuale utente

RIDGID

RIDGID WD1685AU0 Manuale utente

Ezviz

Ezviz RE4P Manuale utente

STG global

STG global TANVAC HDV3000 Manuale utente

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuale utente

Factory

Factory M3340 Manuale utente

Shop-Vac

Shop-Vac VN92 SERIES Manuale utente