Nokia NPD-1 Series Guida
CCS Technical Documentation
NPD-1 Series Transceivers
Issue 1 11/2002 Confidential Nokia Corporation
Troubleshooting — Antenna
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 2 Nokia Corporation Confidential Issue 1 11/2002
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 3
Contents Page No
Troubleshooting - Antenna ............................................................................................ 5
Relevant Documents ................................................................................................. 5
Failures and Corrective Measures ...............................................................................5
Internal antenna not installed or unplated internal antenna installed........................ 5
Stamped contact spring clips missing/miss-installed for internal antenna................ 5
Bottom antenna clip bent or missing......................................................................... 6
Missing whip............................................................................................................. 6
Ungrounded display frame........................................................................................ 7
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 4 Nokia Corporation Confidential Issue 1 11/2002
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 5
Troubleshooting - Antenna
This troubleshooting guide addresses potential failures that will affect the antenna per-
formance of the phone, and discusses methods for correction of these failures.
Relevant Documents
For additional information, refer to the Eagle Antenna Electromechanical Specifications
(DMS03311-EN-2.0) and the Eagle Antenna Module VQD (DMS00188-EN-1.2).
Failures and Corrective Measures
Internal antenna not installed or unplated internal antenna installed
A properly installed and plated Eagle antenna module is shown in Figure 1.
The Eagle antenna module consists of the internal antenna and whip antenna as one
module.
Figure 1: Eagle Antenna Module installed)
If the Eagle antenna module is missing, install one. If an unplated internal antenna is
installed, replace it with a properly plated internal antenna module.
If no internal antenna is installed, the antenna gain will be degraded by more than
25 dB.
Stamped contact spring clips missing/mis-installed for internal antenna
Figure 2 shows the RF feed and ground stamped contact spring clips properly installed.
Figure 3 shows both stamped contacts spring clips missing. If the either contact is miss-
ing or bent, replace antenna module with new antenna.
Figure 2: RF feed and ground stamped contact spring clips properly installed
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 6 Nokia Corporation Confidential Issue 1 11/2002
Figure 3: Stamped contact spring clips missing
Bottom antenna clip bent or missing
The bottom antenna clip is located near the bottom of the phone in the D-cover. A prop-
erly installed bottom antenna clip is shown in Figure 4.
Figure 4: Properly installed bottom antenna clip
If the bottom antenna clip is bent or missing, then it should be carefully replaced with a
new one.
The degradation in antenna performance is only about 2 to 4 dB in the receive portion of
the CELL band when the whip is retracted. PCS band, retracted whip, degradation will be
10 to 15 db.
Missing whip
If the whip is missing, then the Eagle antenna module should be replaced. Figure 5
shows a properly installed whip antenna.
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 7
The whip will perform 2 dB better than the internal antenna in free space. The whip will
perform up to 3 dB better than the internal antenna in talk position.
Figure 5: Properly installed whip antenna
Ungrounded display frame
The display frame is normally grounded by two spring clips (Figures 6). The figure shows
the display frame grounding locations. If clips are missing or bent, replace light guide
with good one. SAR performance will degrade by .5 mW/g for one leg not grounding to
the PWB to over 1.7mW/g if both legs are not grounded.
Figure 6: Display frame grounded by two spring clips
The D cover and light guide have snaps near the display frame ground positions. Make
sure they are locked in position for ESD protection. These snap features help maintain
display leg contact with the PWB.
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 8 Nokia Corporation Confidential Issue 1 11/2002
Altri manuali per NPD-1 Series
4
Indice
Altri manuali Nokia Telefono cellulare
Nokia
Nokia Communicator 9210 Manuale utente
Nokia
Nokia 26086 Manuale utente
Nokia
Nokia 109 Manuale utente
Nokia
Nokia 2760 - Cell Phone 11 MB Manuale utente
Nokia
Nokia 6102 - Cell Phone 4.6 MB Manuale utente
Nokia
Nokia NAVIGATOR 6210 Manuale utente
Nokia
Nokia CLASSIC 6220 Manuale utente
Nokia
Nokia Cellphone 3220 Manuale utente
Nokia
Nokia N97 Manuale utente
Nokia
Nokia RM-140 Manuale utente
Nokia
Nokia Mediamaster 110 S Manuale utente
Nokia
Nokia N85 Scheda tecnica
Nokia
Nokia E55 Manuale utente
Nokia
Nokia RH-3 Series Guida
Nokia
Nokia 110 4G Manuale utente
Nokia
Nokia 6151 - Cell Phone 30 MB Manuale utente
Nokia
Nokia 7270 - Cell Phone 21 MB Manuale utente
Nokia
Nokia Lumia 525 Manuale utente
Nokia
Nokia RM-256 Manuale utente
Nokia
Nokia TA-1243 Scheda tecnica
