Nokia MEDIAMASTER 9761 C Manuale utente

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Owner’s Manual

MEDIAMASTER

9761 C

Hiermit erklärt Nokia, daß dieser digitale Receiver,

Mediamaster 9761 C, den geltenden Anforderungen

sowie anderen geltenden Bestimmungen der

Richtlinie 1999/5/EC entspricht.

Dieses Endgerät ist für den Anschluß an das analoge

öffentliche Fernsprechnetz vorgesehen, bei dem die

Netzwerkadressierung, sofern erforderlich, über

Mehrfrequenzsignale erfolgt.

Par la présente, Nokia déclare que ce récepteur

numérique, le Mediamaster 9761 C, satisfait aux

conditions requises essentielles et est conforme aux

autres dispositions applicables de la Directive 1999/5/EC.

Ce terminal est destiné à être connecté aux réseaux

téléphoniques publics commutés analogiques (RTPC),

dans lesquels l’adressage réseau se fait, le cas

échéant, via un signal multifréquence.

Nokia dichiara che questo ricevitore digitale,

Mediamaster 9761 C, è conforme ai requisisti

fondamentali e alle disposizioni della Direttiva 1999/5/EC.

Questo Terminale Multimediale è stato progettato per

il collegamento alla rete telefonica analogica pubblica

commutata (PSTN), in cui l’indirizzamento di rete, se

fornito, avviene tramite segnalazione DTMF (Dual Tone

Multiple Frequency).

Hereby, Nokia declares that this digital receiver,

Mediamaster 9761 C, is in conformity with essential

requirements and other relevant provisions of

Directive 1999/5/EC. This Terminal Equipment is

intended for connection to the analogue Public

Switched Telephone Networks (PSTNs), in which

network addressing, if provided, is by means of Dual

Tone Multiple Frequency (DTMF) signalling.

DECLARATION OF CONFORMITY

GB 3

MEDIAMASTER 9761 C

Nokia and Nokia Connecting People are registered trademarks of Nokia

Corporation. Other product and company names mentioned herein are

trademarks or trade names of their owners.

Nokia operates a policy of continuous development. Therefore we reserve the

right to make changes and improvements to any of the products described in

this manual without any prior notice.

Contents

General operation 4

For your safety 4

Remote control 5

Front and rear panel 6

Smartcard and CA module 7

General 7

How to insert the smartcard 7

About the CA module 7

Installation of the Mediamaster 8

Preparing the Remote Control 8

Connecting the Mediamaster 8

Connecting the Mediamaster to the TV 9

Connecting a TV and VCR with SCART

connectors 9

Connecting a Satellite Receiver and VCR 10

Connecting to the built in phone modem 10

Connecting a HiFi System 10

Connecting to the mains supply 11

Switching on for the first time with

SCART connections 11

Tuning Procedure when RF Connections

are used 12

First time installation 13

General Information 13

The Welcome Menu 13

Language 13

Initialization 14

Finishing the first time installation 15

If the automatic search procedure failed 15

Viewing mode 16

General Information 16

Programme Information 16

The “i” (Information) Button 17

GUIDE 17

List of TV or Radio Channels 18

Options (Green Button) 18

TV Release (0) 19

Video Recording 19

The TEXT Button (Teletext) 19

EXIT TV 19

Main menu 20

General Information 20

TV and Radio Channels 20

Edit Channels 20

Guide 24

System Configuration 24

Channel Search 24

TV Settings 25

Time Adjustment 25

Modem configuration 26

Automatically Receiver Upgrade 26

Manually Receiver Upgrade 27

Reinstall 27

User Preferences 27

Language Preferences 28

Parental Control 28

Appearance Preferences 29

System Information 30

Conditional Access 31

Reminder List 32

Glossary 33

Problem solving 34

Front panel display 35

Technical specifications 36

GB 4

GENERAL OPERATION OF THE MEDIAMASTER

Throughout this manual you will notice that the everyday opera-

tion of your Mediamaster is based on a series of user friendly on-

screen displays and menus. These menus will help you get the

most from your Mediamaster, guiding you through installation,

channel selection, viewing and many other functions.

All functions can be carried out using the buttons on the remote

control, and some of the functions can also be carried out using

the buttons on the front panel.

Please be aware that new software may change the functional-

ity of the Mediamaster.

Should you experience any difficulties with the operation of your

Mediamaster, please consult the relevant section of this manual,

including the Problem Solving, or alternatively call your dealer or

a customer service adviser.

• Allow clear space around the Media-master for

sufficient ventilation.

• Do not cover the Mediamaster or place it on a

unit that emits heat.

• Use a soft cloth and a mild solution of washing-

up liquid to clean the casing.

• Never allow liquids, spray or other materials to

come into contact with the inside of the

Mediamaster.

• Do not connect or modify cables when the

Mediamaster is plugged in.

FOR YOUR SAFETY

• Do not remove the cover.

• Do not allow the unit to be exposed to hot, cold

or humid conditions.

• Service should be carried out only at a Nokia

Authorised Service Centre.

• Please note that the only way to isolate the

Mediamaster completely from the mains supply

is to unplug the mains lead!

GB 5

To switch the Mediamaster in and out of standby mode.

EXIT TV To return to the viewing mode from a menu without stor-

ing settings (in menu mode).

To switch between TV or Radio (in viewing mode).

To turn the sound off/on (mute).

- + To adjust the volume. The Mediamaster’s maximum level is

controlled by the TV’s present volume setting.

0 - 9 To change channel and to select individual menu options.

Note: If 0 is entered as the first digit, the TV Release func-

tionality is activated (see below).

0 TV Release. To switch between digital TV/Radio, analogue

TV and analogue satellite TV and VCR, when your systems

are connected by SCART leads.

Info. To display short and extended information (if transmit-

ted) about current and next programmes.

BACK To go back one level in the menus without storing settings.

TEXT To select teletext information.

Press to enter teletext (if available).

MENU To display or exit from the ”Main Menu” screen.

GUIDE To obtain a list of present and following programmes for the

available channels. This information is only shown if your

Service Provider transmits programme information (EPG in-

formation).

P+ P- To change channels up and down by one unit.

To change page in a menu/list/text if more than one page is

available. To browse through teletext history.

▲ ▼ To move up/down in the menus and to change channels.

To change settings in menus.

OK To confirm choices and selection of a highlighted item.

To display the TV/Radio channel list (in viewing mode).

(Red) To download an Open TV application.

OPTION (Green) To select service options in viewing mode.

OPTION + code: to open a locked channel.

FREEZE (Yellow) To select the freeze function in viewing mode.

Press once to freeze the screen picture. Press the button

once again to unfreeze the picture.

(Blue) To toggle between present and previous TV/Radio

channels in viewing mode.

This section describes how to operate the Mediamaster using the buttons on the remote control.

Some of the functions can also be carried out using the buttons on the front panel.

REMOTE CONTROL

GB 6

to put the Mediamaster

in and out of standby

mode

to move up/down in

the menus and to

change channels.

Display

shows channel number, error messages, remote con-

trol commands and time in standby mode

Front Panel

Slot

for a smartcard for

future services

Slot

for the smartcard from the

Service Provider

Slot

for a CA module

with a smartcard

Button

to release the

CA module

Rear Panel

AUX SCART

for connection to a VCR

or a satellite receiver

Mains lead

230 V AC

±15%

50-60 Hz

TV AERIAL

for the connec-

tion to the cable

network socket

DIGITAL AUDIO

phono connector

S/PDIF output for

connection to

a HiFi system

TV SCART

for the connec-

tion to the TV

SERIAL

to read and load

data information

TV / VCR

for an RF-lead to

the aerial input of

the TV or a VCR

AUDIO L/R

Connection of a

HiFi system

FRONT AND REAR PANEL

TELEPHONE

for connection to the

telephone network

GB 7

ABOUT THE SMARTCARD AND CA MODULE

PIN Code

The smartcard is loaded with a 4-digit code, also called a PIN code

(Personal Identification Number).

You will be asked to enter this code in order to get access to some

of the functions in the Mediamaster.

General

The Mediamaster box has access to scrambled TV/Radio chan-

nels based on the embedded Nagravision system. To be able to

receive these scrambled digital channels you will need a special

smartcard distributed by your Service Provider.

The Service Provider is the programme distributor of the cable

channels.

It is also possible to connect a separate CA (Conditional Access)

module*to the box. The CA module makes it possible to receive

other scrambled channels (if transmitted on the cable net.)

This module is equipped with its own smartcard and may create

special menus not described in this manual. If so, please follow

the instructions within these menus or from the Service Provider.

After inserting the smartcard, leave it in the slot permanently. Do

not remove it again, unless your Service Provider asks you to do

so. This is important, because if your Service Provider wants to

download new information, the card has to be in the slot.

*Only use a DVB Standard Common Interface CA module.

How to insert the smartcard

•Insert your smartcard fully into the left-hand lower slot be-

hind the lid of the front panel of the Mediamaster. The gold

chip should face downwards and inwards.

•The upper slot is intended for future services such as bank

services and others.

About the CA module

•Follow the instructions delivered together with the CA mod-

ule.

•Insert the module fully into the right-hand slot behind the lid

of the front panel.

•Press the grey button on the front panel to remove the CA

module.

smartcard

CA module

Smartcard for the CA module

GB 8

The box for your Mediamaster should contain the

following items:

•the Mediamaster

•a remote control with 2 AAA batteries

•a SCART lead (fully featured 1,0 metre)

•an Owner’s Manual

•a software license agreement

INSTALLATION OF THE MEDIAMASTER

About the SCART sockets

The rear panel of the Mediamaster is equipped with 2 SCART

sockets (see diagram). When you connect other products to

any of these sockets, always use fully featured SCART leads

(as supplied). There are “less well specified”SCART leads on the

market and picture quality could be reduced if you use them. SCART socket

SCART lead

Owner’s manual License

agrement

Preparing the Remote Control

•Remove the cover on the battery compartment at the bottom

of the remote control.

•Insert the 2 AAA (1,5 V) batteries, as shown in the diagram,

taking care to observe the +and -markings indicated inside.

•Replace the cover.

Connecting the Mediamaster

There are many different types of TV/VCR and other equipment

that you can connect to the Mediamaster.

In this manual you will see some of the most common ways to

connect your equipment.

If you use RF leads you will have to tune your TV and VCR to the

Mediamaster output channel (see page 12).

Remote control

GB 9

Connecting the Mediamaster to the TV

As most local cable network are distributing TV programmes from

both digital and analogue sources, the signal from the wall net-

work socket will be of the two different kinds:

1Digital signal information to be handled by the Mediamaster.

These signals are sent to the TV through the SCART leads.

2Analogue signals which bypass the Mediamaster through RF

leads.

Due to that you must connect the Mediamaster and the VCR

to the TV as discribed below.

•Connect the SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

•Connect an RF lead between the TV/VCR output on the Media-

master and the TV aerial input on your TV.

•Connect an RF lead between the TV AERIAL input socket on

the Mediamaster and the network socket.

SCART

Network

socket

Connecting a TV and VCR with SCART connectors

Refer to your VCR’s manual for full instructions.

If your TV has a SCART socket, but your VCR does not

SCART

Network

socket

SCART

•Connect a SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

•Connect a SCART lead between the VCR

and the AUX SCART socket on the

Mediamaster.

•Connect an RF lead from the TV/VCR output on

the Mediamaster to the TV aerial input on the VCR.

•Connect an RF lead from the RF output on the

VCR to the TV AERIAL input socket on the TV.

•Connect an RF lead between the TV AERIAL input socket

on the Mediamaster and the network socket.

•Follow the connections from above, but without the Media-

master/VCR SCART lead.

Your VCR then will have to be tuned to your

Mediamaster as described on page 12.

VCR

Mediamaster

VCR

Network

socket

INSTALLATION OF THE MEDIAMASTER

GB 10

Connecting a HiFi System

•Connect an RCA/Cinch stereo cable from the AUDIO L R sock-

ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA

input sockets on your HiFi system.

•If available you can connect an RCA/Cinch single cable from

the DIGITAL AUDIO socket on the Mediamaster to your HiFi

or Dolby Pro Logic system.

Note: To avoid interference you must use a screened video

cable.

Connecting a Satellite Receiver and VCR

1 Connect a SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

2 Connect a SCART lead between the TV SCART socket

on the satellite receiver and the AUX SCART socket

on the Mediamaster.

3 If your TV is equipped with two SCART connectors

and the VCR also has a SCART; always use the second

SCART to connect the VCR to the TV.

4 Connect an RF lead from the RF output on the VCR to the TV

aerial input on the TV.

5 Connect an RF lead from the RF output on the satellite re-

ceiver to the RF input socket on the VCR.

6 Connect an RF lead from the TV/VCR output on the Media-

master to the RF input socket on the satellite receiver.

7 Connect an RF lead between the TV AERIAL input socket on

the Mediamaster and the network socket.

8 Connect the coaxial cable between the LNB and the LNB

socket on the satellite receiver.

Both the VCR and the satellite receiver must be tuned to dif-

ferent UHF channels than the Mediamaster when using RF-

connectors.

Satellite

dish

Network

socket

SCART

Media-

master

VCR

Satellite receiver

The satellite receiver must be switched OFF (in standby

mode) when you want to watch digital cable channels

from the Mediamaster.

INSTALLATION OF THE MEDIAMASTER

Connecting to the built in phone modem

The built in phone modem makes it possible for you to use inter-

active services.

•Connect a telephone cable (option) between the socket

marked TELEPHONE on the rear of the Mediamaster and the

ordinary telephone socket in the wall.

Indice

Altri manuali Nokia Ricevitore

Nokia

Nokia Mediamaster 9820 T Manuale utente

Nokia

Nokia 6000 Manuale utente

Nokia

Nokia Mediamaster 9802 S Manuale utente

Nokia

Nokia FastMile Manuale utente

Nokia

Nokia Mediamaster 210 Manuale utente

Nokia

Nokia MEDIAMASTER 9800 S Manuale utente

Nokia

Nokia FastMile 4G Manuale utente

Nokia

Nokia MEDIAMASTER 9780 S Manuale utente

Nokia

Nokia MEDIAMASTER 9701 S GOLD BOX Manuale utente

Nokia

Nokia MD-310 Manuale utente

Nokia

Nokia MD-310 Manuale utente

Nokia

Nokia MEDIAMASTER 9450 S Manuale utente

Nokia

Nokia MEDIAMASTER 9780 S Manuale utente

Nokia

Nokia MEDIAMASTER 211S Manuale utente

Nokia

Nokia MEDIAMASTER 9460 S Manuale utente

Nokia

Nokia MEDIAMASTER 9400S Manuale utente

Nokia

Nokia Mediamaster 260T Manuale utente

Nokia

Nokia Mediamaster 210 Manuale utente

Nokia

Nokia Mediamaster 9602 S Manuale utente

Nokia

Nokia 230 T Manuale utente

Nokia

Nokia Mediamaster 9828 Manuale utente

Nokia

Nokia FastMile 4G Istruzioni operative e di sicurezza

Nokia

Nokia Mediamaster 220S Manuale utente

Nokia

Nokia FastMile 5G14-B Manuale utente

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente