NORDIC PUMP SYSTEMS G4 Manuale utente

Open top of mixing tube, check if it is clean. Also make sure mixing bin is DRY. If wet then dry before using.

Connect power –400/230V If using a generator make sure it is at least 20kva. Check switch inside electrical

cabinet to make sure it is on the correct voltage in relation to power supply.

Connect water to the G4. ¾” hose is the best but you can also use ½”. Turn on water.

G4 water connector, connect water from water supply here

Close all the water release valves on the G4, they are the ones leaking water when the water was turned on. If

nothing was leaking water then valves were already closed. Check water pressure. Needs to be at least 2.5 lbs, if

lower than 2.5 then need a water booster pump if one is not built into this particular machine. If pressure falls

below 2.5lbs then machine will shut off.

Water release valves

Open Water tap on the G4 and let all the air out of the water system. Close tap when done.

Water tap

Connect water hose coming from Volume measuring tube to TOP water connector on mixing tube.

Top water connector

Take off the water cap from the LOWER water connector on the mixing tube.

Turn on RED main power switch on the G4. Press GREEN start button to activate controls. If using 400V then check

to make sure electricity is going in the correct direction, if YELLOW light is on then it is in reverse. Simply turn main

power switch in opposite direction. If using 230V does not matter which direction it is running.

Main power switch

Manual water button

Push the manual water button on control panel while adjusting water volume to desired level. REMEMBER

STARTING WETTER IS MUCH BETTER THAN TOO DRY. When desired level is reached release button, let water drain

out of the lower water connector. When water stops coming out replace cap. Your machine is now primed.

Water volume adjuster knob

Check mortar bin to make sure it is still dry. Add 2 bags of DRY mix. Put a bucket in front of ROTOR STATOR nozzle

to catch the mixed mortar.

Rotor Stator nozzle

Turn on conveyor wheel first. Turn on pump motor switch to the right. Check mortar mixture in bucket. Adjust

water volume to get desired consistency. When consistency is correct turn off pump motor and conveyor wheel.

Mixture is ready.

Pump motor switch / Conveyor wheel switch

Rinse mortar hose with water. Empty out all water from hose. Connect mortar hose to ROTOR STATOR nozzle.

Connect end spraying nozzle. Connect one end of air hose to air nozzle on G4. Connect the other end to the

spraying nozzle. If the G4 doesn’t have its own compressor then connect a compressor to the G4. Needs

minimum 400L per minute compressor.

Turn on compressor

Compressor power button

Turn on compressor switch on the G4

Compressor on switch

Turn on conveyor wheel

Turn on pump motor. You are ready to go. To start spraying turn the air switch on at the end of the spraying

nozzle. To adjust spraying width adjust air tube at the end of the spraying nozzle.

Check pressure in mortar hose on the pressure gauge which is on the Rotor Stator nozzle. Should be MAX 1 bar of

pressure per meter of mortar hose.

If Amps are too high machine will turn itself off. If machine turns itself off then mix is too dry, hose is plugged,

speed is too fast, wrong mixing product or hose is too long.

To adjust mixture again simply adjust water volume in small amounts. Give it a minute to go through the hose

before you see the new mixture consistency.

If no power try pushing Green button again. A safety stop was probably triggered.

If Red light is on call us.

TBU / PFT Office - Pete Ternsten jr Mobil: 47-93235663

Turn off conveyor wheel and allow mixture to empty out of hoses until only water comes out the end of nozzle.

Turn off pump switch when its only water coming out.

Pump switch

Turn off air compressor

Open air nozzle at end of hose then disconnect air hose. Use very rough brush to clean out end of air tube at the

end of spraying nozzle. Clean with soapy water.

Rough brush

Check pressure in mortar hose. Pressure should be zero. If pressure is not zero then run machine in reverse for a

few seconds until pressure is zero. When pressure is zero disconnect mortar hose.

Mortar hose pressure gage

Disconnect spraying nozzle and clean with water.

Insert 2 small orange cleaning balls into end of mortar hose. Connect mortar hose to water outlet on G4 with

special hose adapter. Turn on water until small balls come out other end of hose. Do it two times. Hose is now

clean. Disconnect mortar hose.

Special hose adapter

G4 water outlet

Connect water hose to water outlet on G4. Open top of mixing tube and rinse thoroughly. Close top. Push GREEN

start button, turn on pump motor and run machine for a few seconds to clean out water in mixing tube. Turn off

pump motor when done.

Open top of mixing tube again. Remove mixing blade and replace with cleaning tool. Close top, push GREEN

start button and run machine a few seconds to clean inside of tube. Make sure water is on. Open top of tube

and check to see if clean. If not repeat process again. If you open the mixing tube you must push GREEN start

button again to activate controls.

Mixing shaft cleaning tool

Replace mixing blade.

Open lower water cap on mixing tube and clean with water.

Turn off main RED power switch. Clean dry mortar bin. Remove top grill and clean with water. Remove dust cover

and clean. Remove conveyor wheel and clean. Remove bottom drain valve under dry bin and clean inside bin

with water, draining all water out when done. Replace everything when done.

Clean outside of machine with soapy water and brush. Rinse.

Open mixing tube and clean with water one more time. Close lid.

Turn off water on G4. Turn on main RED power switch. Push GREEN power button, turn on pump motor and run

machine for a few seconds draining all water out of machine. When water stops coming out the Rotor/Stator

then shut off. DO NOT RUN TOO LONG WITH NO WATER IT WILL BURN UP THE ROTOR/STATOR!

Water should stop coming out here

Clean out the end of the ROTOR/STATOR by spraying the inside out with water.

Turn off main RED power switch. Unplug the machine.

Disconnect water from machine. Drain all 3 water release valves and leave open.

Indice

Manuali Attrezzature per l'edilizia popolari di altre marche

SASFORKS

SASFORKS EXTREME Manuale utente

Hailo

Hailo H-50 Manuale utente

Graco

Graco LineLazer ES 1000 Manuale per l'uso e la cura

Greenlee

Greenlee 555RSC Manuale utente

Manitowoc

Manitowoc Grove CD3340B Manuale utente

Lux Tools

Lux Tools A-FMR-20 Set Manuale utente

SIP

SIP 03683 Manuale utente

Volvo

Volvo L30G Manuale utente

Grizzly

Grizzly G8712 Manuale utente

Modulift

Modulift CMOD 12 Manuale utente

Case

Case DV201 Manuale utente

Sealey

Sealey SC10.V2 Manuale utente

Wacker Neuson

Wacker Neuson DT05 Manuale utente

HYVA

HYVA AMCO VEBA 81 Series Manuale utente

Atlas Copco

Atlas Copco Dynapac V5100TV Manuale utente

Toro

Toro 323 Manuale utente

Manitowoc

Manitowoc National Crane 1400A Manuale utente

SGS

SGS EC1500 Manuale utente