Novexx Solutions LTSI Manuale utente

01/13 Rev. 5.05-01 USER / SERCICE MANUAL

LTSI

Mounting and setting the LTSI

Required Components .................................. 2

Fitting the Applicator ..................................... 3

Setting the Applicator ....................................4

„Must“-parameters ..................................... 4

„Can“-parameters ...................................... 4

Adjusting the Applicator Home Position .... 5

Setting the Dispense Position ................... 6

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI

LTSI Required Components

Required Components

Component Part number Picture

Basic module

LTSI 80/200 (fig.) A4787

Basic module

LTSI 80/400 A4788

Aluminium plate

(with screws 2x DIN912 M5x12

and 2x DIN912 M8x20) A2661

[Tab. 1] Required components to fit the LTSI to an 64-xx. The basic

module is only required in one version.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI

LTSI Fitting the Applicator

Fitting the Applicator

Tools

Allen screwdriver 4 and 6mm

Mounting

1. Switchofftheprinteranddisconnect thepowerplug

from the power outlet!

2. Remove the flange cover from the mounting flange

[1A]

3. Boltthe adapterplate [2A]ontothemountingflange

(2x M5x16).

4. Bolt the applicator to the aluminium plate (2x

M8x20 with lock washers) [3].

5. Plug the applicator cable to the printer [3A].

[6] Applicator mounting flange (A).

[7] Adapter plate (A) ready mounted.

[8] LTSI ready mounted and connected.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI

LTSI Setting the Applicator

Setting the Applicator

„Must“-parameters

„Can“-parameters

WARNING!

Danger of getting hands crushed at the following locations:

• Between applicator pressure plate and printer dispensing edge.

• Between applicator pressure plate and conveyor (if applicable).

During operation, keep your hands away from the moving area of the applicator.

Switch off the printer before any servicing or repair work.

Parameter Setting

DISPENSER PARA > Start source USI

DISPENSER PARA > Dispensing edge long

DP INTERFACE > Interface type USI applicator

DP INTERFACE > Start print mode Level low active a

a) This setting is imperative, if parameter DP INTERFACE > Apply mode is set to

„After start sig.“

DP INTERFACE > End print mode Mode 1

DP INTERFACE > Internal inputs Enabled

[Tab. 2] These parameter settings are imperative for the printer

operation with an applicator.

Parameter

DISPENSER PARA > Application mode

DP INTERFACE > Start print mode a

a) This setting is only arbitrary, if parameter DP INTERFACE >

Apply mode is set to „After print“.

DP INTERFACE > Apply mode

[Tab. 3] These parameters can be used to adapt the applicator ope-

ration to the application.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI

LTSI Setting the Applicator

Adjusting the Applicator Home

Position

After fitting the applicator, the home position of the ap-

plicator must be checked and adjusted if necessary.

When viewed from the side, the applicator plate must

stand slightly above and in front of the dispensing edge

[4].

The following guide values may used for the dis-

tances from the dispensing edge:

• Horizontal: approx. 1 mm

To adjust: Shifting of the left aluminium plate [5A]

– upwards --> shifts the home position further

away from the dispensing edge.

– downwards --> shifts the home position closer

to the dispensing edge.

• Vertical: approx. 0.5 mm

To adjust: Shifting of the right aluminium plate [5B]

– upwards --> shifts the home position upwards.

– downwards --> shifts the home position down-

wards.

[9] Applicator in home position.

[10] Adjusting the home position. Remove the gaiter to get to tho-

se aluminium plates.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI

LTSI Setting the Applicator

Setting the Dispense Position

The label can either be dispensed so that it is entirely

free from the carrier material, or it can remain adhering

to the carrier material via a small strip when the feed

stops [6].

The required width of this strip depends on the type of

further processing and is set via a printer parameter.

When using the applicator, the dispensing position

should be set so that the label is just released when dis-

pensed, i.e. so that it no longer adheres to the carrier

material.

Advancingthecarriermaterialtoofar cancause strings

of adhesive to pull the label down with them.

Setting via the PRINT PARAMETERS >Dispenseposition pa-

rameter.

[11] Adjusting the dispense position.

Dispensed label Dispense position

Dispensing edge

Backing paper

Indice

Altri manuali Novexx Solutions Stampante

Novexx Solutions

Novexx Solutions TTX 50 Series Manuale utente

Novexx Solutions

Novexx Solutions 64- series Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions AP 3.4 Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions TTX 50 Series Manuale utente

Novexx Solutions

Novexx Solutions TTX 350 Ocelot Manuale utente

Novexx Solutions

Novexx Solutions XLP 504 Manuale utente

Novexx Solutions

Novexx Solutions U-RX Manuale utente

Novexx Solutions

Novexx Solutions AP 5.4 Manuale utente

Novexx Solutions

Novexx Solutions EIDOS XTO2ce Manuale utente

Novexx Solutions

Novexx Solutions AP 5.4 Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions Cutter 2000 Guida alla risoluzione dei problemi

Novexx Solutions

Novexx Solutions 64- series Manuale utente

Novexx Solutions

Novexx Solutions 64- series Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions ALS 30 Series Manuale utente

Novexx Solutions

Novexx Solutions 64- series Guida alla risoluzione dei problemi

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions 64- series Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Novexx Solutions

Novexx Solutions LA-SO Manuale utente

Novexx Solutions

Novexx Solutions ALX 73 Series Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente