Novus NVC-402C Manuale utente

u s e r ’s m a n u a l

NVC-402C

NVDN-402C

NVC-402C, NVDN-402C 1.0 version - User’s manual

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with the requirements of the following directives and national

regulations implementing the directives:

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and as well as 75VDC and

1500VDC.

WEEE Directive 2002/96/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for used

up electrical and electronic equipment for recycling purpose. For more information about recycling of this

product, please contact your local authorities, your household waste disposal service or the shop where

you purchased the product.

RoHS Directive 2002/95/EC

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances

in electrical and electronic equipment, have been designed and manufactured in compliance with the above

mentioned regulations. Simultaneously, we claim that our products have been tested and do not contain

hazardous substances whose exceeding limits could have negative impact on human health or natural

environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

The manufacturer is not responsible for defects and damages that result from improper or inconsistent with

user’s manual installation of the device in the system.

INFORMATION

NVC-402C, NVDN-402C 1.0 version - User’s manual

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A

PROPER DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE

YOURSELF WITH THE MANUAL PRIOR TO INSTALLATION AND FURTHER

DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF

EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN

ACTION.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a

direct influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer

is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers

etc.) is not recommended since it may lead to heat build-up and damaging the device itself

as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden.

Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The

camera must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual;

SAFETY REQUIREMENTS

NVC-402C, NVDN-402C 1.0 version - User’s manual

SAFETY REQUIREMENTS

9. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply

the camera from a power sources with unknown parameters, unstable or not meeting producer’s

requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the

possibility of damaging them by accident. Special attention must be paid to cables getting from the

camera and connecting the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made

discharge-, overload- and lightning protection devices. Usage of separating transformers is

advised;

12. Electric installation supplying the device should be designed to meet the specifications given

by the producer in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should

be conducted only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance

department when the following occurs:

 Damages to the power cord or to the plug itself;

 Liquids getting inside the device or exposure to strong mechanical shock;

 Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer and possible to apply by user himself, seem not to have any effect;

 Camera is damaged;

 Atypical behaviour of the camera components may be seen (heard).

16. In necessity of repairs attention to using only original replacement parts (with their parameters

in accordance with those specified by the producer) should be paid. Non-licensed service and

non-genuine replacement parts may cause fire or electrocution;

17. After maintenance activities tests should be run to ensure proper operation of all the functional

components of the device.

Attention!

Technical changes reserved without prior notice and printing errors possible.

NVC-402C, NVDN-402C 1.0 version - User’s manual

1. PACKAGE CONTENTS

 Video camera with plug in the lens mounting place

 Mount adapter for C type lens mount

 L wrench

 4 pin Mini-DIN connector (for video or DC-type auto-iris lens)

 Power connector

 User’s manual

If any of the listed equipment has been damaged during transport or if the package is incomplete,

the contents of package should be packed back in to the original box. Please contact your local

NOVUS distributor for further assistance.

2. MAIN CHARACTERISTICS

 Electronic day/night function (NVC-402C)

Mechanical IR cut filter (NVDN-402C)

 Horizontal resolution: 650 TVL (NVC-402C)

Horizontal resolution: up to 700 TVL (NVDN-402C)

 Min. illumination: 0.05 lx/F=1.2 (NVC-402C)

Min. illumination: from 0.005 lx/F=1.2 (NVDN-402C)

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 High Light Compensation (HLC)

 Privacy zones: 4

 Other functions: various picture effects, motion detection

 OSD menu, available:

Locally - from the buttons at the rear of the camera

Remote - by coaxial cable using remote controller NC-RCUTC (optional)

 Enclosure color: White

 Power supply: 12 VDC

FOREWORD INFORMATION

NVC-402C, NVDN-402C 1.0 version - User’s manual

3. SPECIFICATION

FEATURES AND SPECIFICATION

Model NVC-402C NVDN-402C

Pick-up element CCD imager, 1/3” SONY Super HAD II

Number of Effective Pixels 976 (H) × 582 (V)

Horizontal resolution 650 TVL –color mode,

700 TVL –B/W mode

650 TVL –color mode,

650 TVL –B/W mode

Min. illumination 0.05 lx/F=1.2 –color mode (1/50 s),

0.05 lx/F=1.2 –B/W mode (1/50 s)

0.05 lx/F=1.2 –color mode (1/50 s),

0.005 lx/F=1.2 –B/W mode (1/50 s)

S/N Ratio ≥52 dB

Electronic Shutter Auto: 1/50 s ~ 1/100 000 s

Mount C/CS

Iris Mode D

Type Electronic D/N function Mechanical IR cut filter

Switching Mode Auto / Manual

Switching Level Adjustment Yes

Switching Delay 0 ~ 255 s

OSD English, Russian and others

Back Light Compensation

(BLC) Yes

High Light Compensation

(HLC) Yes

Wide Dynamic Range

(WDR) Yes

Digital Noise Reduction

(DNR) Yes

Privacy Zones 4

Motion Detection Yes

Image Processing Mirror effect, sharpening

Video Output BNC, 1.0 Vp-p, 75 Ohm

Dimensions (mm) 58(W) x 62 (H) x 128 (L)

Weight 370 g

Enclosure Aluminium, white

Power Supply 12 VDC

Power Consumption 0.9 W

Operating Temperature -30°C ~ 45°C

NVC-402C, NVDN-402C 1.0 version - User’s manual

3.1 Dimensions

3.2. View of the camera, layout of the camera items

Rear view

1,2,4,5 - direction buttons LEFT, UP, RIGHT, DOWN

3- SET button

6 - POWER supply diode

7- BNC connector

8- Auto Iris Lens Connector

9 - Power supply connector 12V DC

FEATURES AND SPECIFICATION

NVC-402C, NVDN-402C 1.0 version - User’s manual

Focus Adjusting Fixing

Screw

Focus Adjusting

4. INSTALLATION

4.1 Lens installation

The NVC-402C and NVDN-402C cameras support manual and auto iris D type lenses. It is

recommended to use IR series lenses for day/night camera and for cooperation with IR illuminators.

In case of operation with IR illuminators it is necessary to use IR series lenses.

Thanks to ring, application usage of C-mount lenses is possible .

Note: In case of using CS-mount lenses additional ring is not needed.

4.1.1 Fixed iris lens installation

In order to install manual iris lens one should:

 Carefully remove the plug protecting the CCD pick-up element

 Carefully screw the lens to the end of the thread till slight resistance can be felt

 Supply power to the camera, adjust focal length and focus. In the MAIN SETUP menu set lens

control as MANUAL and set appropriate mode of electronic shutter

Note: For best results, perform focus adjustments at night (with iris fully opened) or while

using a #6 or #8 welder's glass in front of the lens to avoid overexposure.

INSTALLATION

C-mount lens

CS-mount lens

Ring

Side view

NVC-402C, NVDN-402C 1.0 version - User’s manual

4.1.2 Auto iris lens installation (type D)

In order to install auto iris lens one should:

 Carefully remove the plug protected the CCD pick-up element

 Carefully screw the lens till slight resistance can be felt

 Plug the connector into the auto iris jack of the camera

 Set the DC/VIDEO driver switch on the DC position

Note: If lens cable does not end with a connector use the connector supplied with the camera.

According to the lens manual and advices below, one should solder the

cables to the connector and protect them against short circuit by the heat shrink

sleeves.

 In the camera menu set lens control as DC

 Supply power to the camera, adjust focal length and focus

Note: For best results, perform focus adjustments at night (with iris fully opened) or while

using a #6 or #8 welder's glass in front of the lens to avoid overexposure.

Note: The cameras are equipped with the circuit for iris control with the voltage level ad-

justment in the menu. Default settings are selected for the optimum quality of video

signal. It is not recommended to make any changes if it is not necessary. In case of

changes it is recommended to use #6 or #8 welder's glass in front of the lens and see

the signal on the oscilloscope. During adjustment AGC feature should be switched

off.

INSTALLATION

Pin 3 Pin 4

Pin 1 Pin 2 Heat shrink

sleeves

Top part

of the connector Lens cable

Bottom part of

the connector

Pin Function

1 Dumping coil -

2 Dumping coil +

3 Drive coil +

4 Drive coil -

NVC-402C, NVDN-402C 1.0 version - User’s manual

Power connector

4.1.3 Manual iris lens installation

In order to install manual iris lens one should:

 Carefully remove the plug protecting the CCD pick-up element

 Carefully screw the lens till slight resistance can be felt

 Supply power to the camera, adjust focal length and focus. In the MAIN SETUP menu set lens

control as MANUAL and appropriate mode of electronic shutter.

Note: For best results, perform focus adjustments at night (iris is full open) or while using a #6 or

#8 welder's glass in front of the lens to avoid overexposure.

Note: The level of iris opening should be adjusted with camera pointed to a scene with highest

possible illumination (at its installation place). Please focus on obtaining a picture with

highest illumination, but without overexposing the picture.

4.2 Power supply connection

Warning: Device should be supplied only from a power sources whose parameters are in accordance

with those specified by the producer in the camera technical datasheet. Therefore, it is

forbidden to supply the camera from power sources with their parameters unknown,

unstable or not meeting the producer’s requirements.

 NVC-402C and NVDN-402C are 12VDC ± 10% supplied. Please make sure proper polarity is

maintained.

 It is possible to use additional power connector, but please make sure proper polarity is

maintained (in accordance with power connector signs).

INSTALLATION

Power supply connector 12V DC

Indice

Lingue:

Altri manuali Novus Telecamera a circuito chiuso

Novus

Novus NVAHD-1DN3102H/IR-1 Manuale utente

Manuali Telecamera a circuito chiuso popolari di altre marche

CCTV Center

CCTV Center 27Z540 Series Manuale utente

VHD

VHD DA-S36 Manuale utente

CIS

CIS VISION:mini VCC-F22S29ACL Guida rapida

Eagleye

Eagleye IS-NIPHB40NSC130 Series Manuale utente

JAI

JAI LQ-201CL Manuale utente

Uniq

Uniq UP-1800CL-12B Manuale utente

Hitachi Kokusai Electric

Hitachi Kokusai Electric SK-HD1200 Manuale utente

Channel Vision

Channel Vision 6404 Manuale utente

Rausch

Rausch minCam Manuale utente

Retina

Retina RET1032 Manuale utente

Intellisystem

Intellisystem IT-VCHD1600JSE Manuale utente

Hitachi

Hitachi HV-F31CL Manuale utente

VIDCOM

VIDCOM KIR-R639D40 Manuale utente

Sony

Sony HDC5500 Manuale utente

Sony

Sony KDP-673SH20 Manuale utente

Ikegami

Ikegami ISD-A20 Manuale utente

Basler Vision Technologies

Basler Vision Technologies Sprint Manuale utente

FLIR

FLIR Ax5 series Manuale utente