NuAire XS Manuale utente

XS-MFC Remote Switch Control

Designed to work in conjunction with the XS range of fans

and associated integral and remote sensors, the XS-MFC

Remote Switch Control offers the user the following:

a) On/Off.

b) Maximum or Economy performance.

c) Variable Speed Control.

d) Forward/Reverse airflow.

e) Auto/Manual operation.

Refer to the unit lift up lid for switch operating instructions.

The Remote Switch can control one fan or multiple fans,

depending on the fan and type of sensor being used.

Up to 5 fans (6 inch/9 inch) can be controlled by one XS-MFC.

Up to 2fans (size 12 inch) can be controlled by one XS-MFC.

Note: Do not mix fans of different sizes on the same control.

Siting position

Mount in a vertical plane with the grille at the bottom.

Mount the switch 1.5 metres from the floor (minimum).

Do not expose to excessive amounts of oil, grease or direct

water spray.

Do not subject switches to a direct heat source in excess

of 25oC.

Installation

Follow the pictorial sequence on this page.

Isolation - Before commencing work make sure

that the unit is electrically isolated from the mains supply.

13.04.23. Leaflet Number 671062

XS Fans Switches & Sensors

Remote Switch Control: XS-MFC

Integral Sensors: XS-PIR, XS-H, XS-AQ, XS-TH, XS-TA

Remote Sensors: XS-PIRR, XS-HR, XS-AQR

Installation Guide

The EMC Directive

2014/30/EU

The Low Voltage

Directive

2014/35/EU

Lift up panel and remove

two screws to dismantle

unit.

Push out backplate box

cable entry using a

screwdriver.

Spot through backplate

box and drill and plug

the wall. Fix backplate

box to the prepared wall.

Feed approx. 200mm of

supply cable into the box.

Connect the end of the

cable into the control

block. Connect wires as

shown in the appropriate

wiring diagram.

Hook lip of security

strap (if fitted) in hinge

socket. Fit the control

into the backplate box &

secure.

Test the installation.

200mm

Nuaire: A Trading Division of Polypipe Western Industrial Estate Caerphilly United Kingdom CF83 1NA

T: 029 2088 8911 E: [email protected] W: www.nuaire.co.uk

Isolation - Before commencing work make sure

that the unit is electrically isolated from the mains supply.

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

XS Integral Sensors

Designed to work in conjunction with and fit inside the XS

range of fans, the range of XS Integral Sensors offer the

user the following functions:-

XS-PIR

Passive Infra Red movement detector - senses body move-

ment, Run on Timer is adjustable between 2 and 40 minutes.

XS-H

Humidity Sensor - senses relative humidity. Adjustable

between 30% and 90% RH. Run on Timer is adjustable

between 2 and 40 minutes.

XS-AQ

Air Quality Sensor - detects odours and tobacco smoke.

Adjustable to suit size requirements. Run on Timer is adjustable

between 2 and 40 minutes.

XS-TH

Temperature Sensor - suitable for temperatures up to 25°C

(occasionally 35°C)

XS-TA

Run on Timer - adjustable between 2 and 40 minutes.

Siting

Mounted inside a fan.

Grille section adjacent to sensor must be changed to suit the

sensor being used (see fig 1).

Do not expose to excessive amounts of oil, grease or direct

water spray.

Do not subject sensors to a direct heat source in excess

of 25oC.

Installation

Follow the pictorial sequence on this page.

Push out the sensor

area cover from the

grille.

Remove the module plate.

Connect sensor to

fan using pre-wired

plug.

Screw the sensor

module into position

on the fan.

Fit new grille

insert into main

grille.

Isolation - Before commencing work make sure

that the unit is electrically isolated from the mains supply.

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

XS Remote Sensors

Designed to work in conjunction with the XS range of fans,

the range of XS Remote Sensors offer the user the following

functions:-

XS-PIRR

Passive Infra Red movement detector - senses body move-

ment, Run on Timer is adjustable between 2 and 40 minutes.

XS-HR

Humidity Sensor- senses relative humidity. Adjustable between

30% and 90% RH. Run on Timer is adjustable between 2 and

40 minutes.

XS-AQR

Air Quality Sensor- detects odours and tobacco smoke.

Adjustable to suit size requirements. Run on Timer is adjustable

between 2 and 40 minutes.

Note: Refer to the lift up lid for sensor operating

instructions.

Siting

Mount in a vertical plane.

The grille in sensor box should be at the bottom.

Mount the sensor 1.5 metres from the floor.

Do not expose to excessive amounts of oil, grease or direct

water spray.

Do not subject switches to a direct heat source in excess

of 25oC.

Installation

Follow the pictorial sequence on this page.

200mm

of cable

inside

box

1.5m

Remove screws

securing cover

to box.

Knock out cable entry

point and feed the

supply cable through

allowing approx.

200mm of cable to

protrude into box.

Drill & plug the

surface and fix the

back box to the wall.

If security strap

XS-SS is to be fitted:

Locate boss

centrally in slots.

Wire in the sensor

(see various wiring

options in the wiring

section),

Screw the sensor

module into position

on the wall. Hook lip

of security strap

(if fitted) in hinge

socket and secure

the boss using

the screw.

Isolation - Before commencing work make sure

that the unit is electrically isolated from the mains supply.

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

Electrical Wiring for One Fan

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

(Shutter Operation XS fans)

There will be a short delay on startup and shutdown of

approximately 40 seconds. This is normal.

Wiring - Multiple Fans

Remote switch may be set:

On / Off, Forward / Reverse,

Economy / Std. (variable speed),

Auto / Manual.

Additional fans may be added

up to limit of control:

Up to 5 fans (size 6" / 9") can be

controlled by one XS-MFC.

Up to 2fans (size 12") can be

controlled by one XS-MFC.

Do not mix different fan sizes

on the same controller

XS-MFC controller

Double

pole

isolator

Fuse

max.

3 amp

XS Fan unit

230v 50Hz

supply

XS Fan unit

Multiple fans operated via remote XS-MFC control

XS-MFC controller

XS Fan unit

SENSOR

230v 50 H z

supply

XS Fan unit

L2 L1 N

Remote switch may be set:

On / Off, Forward / Reverse,

Economy / Std. (variable speed),

Auto / Manual.

Additional fans may be added

up to limit of control:

Up to 5 fans (size 6" / 9") can be

controlled by one XS-MFC.

Up to 2fans (size 12") can be

controlled by one XS-MFC.

Do not mix different fan sizes

on the same contr.oller

XS Fan unit

Double

pole

isolator

Fuse

max.

3 amp

Multiple fans operated via remote XS-MFC

control and a Remote Sensor

XS-MFC controller

(Required only when using Timer)

XS Fan unit

230v 50Hz

supply

Remote switch may be set:

On / Off, Forward / Reverse,

Economy / Std. (variable speed),

Auto / Manual.

Multiple fans operated via remote

XS-MFC control and one

Integral Sensor in Fan 1

Additional fans may be added

up to limit of control:

Up to 5 fans (size 6" / 9") can be

controlled by one XS-MFC.

Up to 2fans (size 12") can be

controlled by one XS-MFC.

Do not mix different fan sizes

on the same controller.

Double

pole

isolator

Fuse

max.

3 amp

XS Fan unit

Fan unit

(fitted with

integral

sensor)

Multiple fans operated via remote XS-MFC control and

one Integral Sensor in Fan 1

Remote switch may be set:

On / Off, Forward / Reverse,

Economy / Std. (variable speed),

Auto / Manual.

XS-MFC controller

SENSOR1

XS Fan unit

230v 50Hz

supply

L2 L1 N

SENSOR 2

L2 L1 N

Double

pole

isolator

Fuse

max.

3 amp

Fan operated using remote XS-MFC control

and a Multiple Remote Sensor

Note:

Note: If 2 x 12 nch fans or 3 x 6 or 9 nch fans are used n the

same operat ng mode n the same room they should all be

controlled from the same MFC speed control. Th s avo ds the

poss b l ty of one fan ( f speed controlled at a lower flow rate)

be ng stalled by the other fan(s).

Adequate make-up a r prov s on suff c ent to prov de vent lat on n

accordance w th bu ld ng regulat ons s requ red n all rooms. Th s

should be checked dur ng comm ss on ng w th all fans n the same

room runn ng together n all poss ble conf gurat ons.

The automat c shutters, motor bear ngs should be frequently

nspected and ma nta ned to ensure they open fully/operate

sat sfactor ly. Use of an RCD and fused spur w th 1A, Bussmann

TDC180, BS1362, fuse (Farnell order no: 1123029) for 1 fan or 2A,

Bussmann TDC180, BS1362 fuse (Farnell order no: 1123032) for 2

or 3 fans s recommended.

Always conf rm a rflow d rect on before comm ss on ng.

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and

dimensions of equipment and the right is reserved to make such changes without prior notice.

Maintenance

Periodically, at least once a year, or more frequently in case of

heavy use, remove the dirt and encrustation from the casing.

Replacement of Parts

As a manufacturer Nuaire is aware that time is important. In

the event of a breakdown of this equipment, it should be

adequately packaged and returned to Nuaire.

IMPORTANT!

Please telephone Nuaire before posting your unit. We will

give you a returns number to identify your package.

We will endeavour to repair or replace it within five working

days of receipt. See our warranty terms.

Warranty

The 3 year warranty starts from the day of delivery and

includes parts and labour for the first year. The remaining

period covers replacement parts only.

This warranty is void if the equipment is modified without

authorisation, is incorrectly applied, misused, disassembled, or

not installed, commissioned and maintained in accordance with

the details contained in this manual and general good practice.

The product warranty applies to the UK mainland and in

accordance with Clause 14 of our Conditions of Sale.

Customers purchasing from outside of the UK should contact

Nuaire International Sales office for further details.

A unit returned to Nuaire should be suitably protectively

packaged and clearly marked with the ‘returns number’

obtained from Nuaire prior to posting.

After Sales Enquiries

For technical assistance or further product information,

including spare parts and replacement components, please

contact the After Sales Department.

Telephone 02920 858 400

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

Notes

13.04.23. Leaflet Number 671062

Installation Guide XS Switches and Sensors

Western Industrial Estate

Caerphilly United Kingdom

CF83 1NA

T: 029 2088 5911

F: 029 2088 7033

E: [email protected]

W: www.nuaire.co.uk

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NuAire Interruttore

NuAire

NuAire DRI-ECO-2S Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente