Nuvoton NuMicro DALI 2 SLAVE Manuale utente

DALI 2nd Slave

Jul 11, 2019 Page 1of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

ARM®Cortex®-M

32-bit Microcontroller

NuMicro®Family

DALI 2nd Slave

User Manual

The information described in this document is the exclusive intellectual property of

Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.

Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system

design. Nuvoton assumes no responsibility for errors or omissions.

All data and specifications are subject to change without notice.

For additional information or questions, please contact: Nuvoton Technology Corporation.

www.nuvoton.com

DALI 2nd Slave

Jul 11, 2019 Page 2of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

Table of Contents

1General Description ......................................................................................................3

Feature .................................................................................................. 31.1

NuMicro®NDA102 Series Feature.................................................................. 41.2

2Nuvoton DALI 2nd Slave Hardware Introduction............................................................5

Jumper Description.................................................................................... 52.1

2.1.1 Power Interface .................................................................................................5

2.1.2 ICE interface for Nu-Link ......................................................................................5

2.1.3 DALI Bus Interface .............................................................................................6

2.1.4 DALI Interface and UART Interface..........................................................................6

2.1.5 Peripherial Interface............................................................................................6

3How to Start Nuvoton DALI 2nd Slave on the KEIL μVISION®IDE................................7

Keil μVision®IDE Software Download and Install ................................................ 73.1

Nuvoton Nu-Link Driver Download and Install .................................................... 73.2

Hardware Setup........................................................................................ 73.3

4How to Start Nuvoton DALI 2nd Slave on the IAR Embedded Workbench ....................8

IAR Embedded Workbench Software Download and Install.................................... 84.1

Nuvoton Nu-Link Driver Download and Install .................................................... 84.2

Hardware Setup........................................................................................ 84.3

5Nuvoton DALI 2nd Slave Quick Start .............................................................................9

Hardware Setup........................................................................................ 95.1

Initialisation ............................................................................................105.2

DALI Commands......................................................................................115.3

Monitoring Page.......................................................................................125.4

Button Function .......................................................................................125.5

6Nuvoton DALI 2nd Slave Schematic ............................................................................ 13

NDA102EC1 Control Unit Schematic..............................................................136.1

DALI Bus Schematic .................................................................................146.2

LED Schematic........................................................................................156.3

Power and Peripheral Schematic ..................................................................166.4

7REVISION HISTORY..................................................................................................17

DALI 2nd Slave

Jul 11, 2019 Page 3of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

1GENERAL DESCRIPTION

The Nuvoton DALI 2nd Slave is the specific development tool for DALI application. DALI is a protocol

for digital addressable lighting device. The Arm®Cortex®-M0 core NuMicro®NDA102 series

microcontroller is used as the main microcontroller in the demo board.

The NuMicro®NDA102 series 32-bit microcontrollers are embedded with ARM®Cortex®-M0 core for

industrial applications which need high performance, high integration, and low cost. It runs up to 48

MHz and offers 29.5 KB embedded program Flash, size configurable Data Flash (shared with program

Flash), and 4 KB SRAM. The NDA102 series has many system level peripheral functions, such as I/O

Port, Timer, UART, SPI, I2C, PWM, ADC, Watchdog Timer, Analog Comparator, Hardware Divider and

Brown-out Detector. These useful functions make the demo board suitable for DALI standard

implementations, and helps users to accelerate the development process. The NDA102’s fast

computing ability allows faster device control and compound applications.

Feature1.1

Compliance

IEC 62386-102:2014

IEC 62386-207:2009

IEC 62386-206:2009

IEC 62386-209:2011 (Colour Type Tc)

Future support: IEC 62386-103:2014, IEC 62384-2XX, IEC 62384-3XX

Color and dimming control for RGB LED

ADC, ECAP and UART interface for secondary development

Easily connect to Nuvoton DALI Master and software tool - DALI Controller on PC

Figure 1-1 DALI 2nd Slave

DALI 2nd Slave

Jul 11, 2019 Page 4of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

NuMicro®NDA102 Series Feature1.2

ARM®Cortex®-M0 core running up to 48 MHz

Memory

29.5 KB Flash memory for program memory (APROM)

Configurable Flash memory for data memory (Data Flash)

2 KB Flash memory for loader (LDROM)

Three 0.5 KB Flash memory for security protection (SPROM)

4 KB SRAM for internal scratch-pad RAM (SRAM)

Up to 8-ch PWM output with 16-bit resolution

Fast computing ability by using hardware divider

Up to 8 single-end ADC input channel with 12-bit resolution and 10-bit accuracy guaranteed

The A/D converters can be started by software, external pin or PWM trigger

Operating temperature: -40℃~105℃

DALI 2nd Slave

Jul 11, 2019 Page 5of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

2NUVOTON DALI 2nd SLAVE HARDWARE INTRODUCTION

The Nuvoton DALI 2nd Slave uses NuMicro®NDA102 series NDA102EC1 as the main microcontroller.

The demo board can connect to a DALI system through the DALI bus. The demo board contains one

RGB LED, one photoresistor, one potentiometer, one ICE interface and peripherial interfaces. It is

suitable for DALI standards implementations.

Figure 2-1 Nuvoton DALI 2nd Slave

Jumper Description2.1

2.1.1 Power Interface

JP1 & JP2

Interface Signal Name

MCU Pin Assignment

Pin 1, 2, 3, 4

5 V

VDD

Pin 5, 6, 7, 8

GND

VSS

2.1.2 ICE interface for Nu-Link

JP3

Interface Signal Name

MCU Pin Assignment

Pin 2

VDD

Pin 4

ICE_DAT

Pin 6

ICE_CLK

Pin 7

UART0_TX

Pin 8

ICE_RST

nRESET

Pin 9

UART0_RX

Pin 10

GND

VSS

5V Power Supply

Reset SWD Interface

DALI Bus DALI Bus

RGB LED

NDA102EC1

Photoresistor

Potentiometer

ADC Interface

UART, DALI TX

and RX Test Pin

DALI 2nd Slave

Jul 11, 2019 Page 6of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

2.1.3 DALI Bus Interface

JP4 & JP5

Interface Signal Name

MCU Pin Assignment

Pin 1, 2, 7, 8

GND

VSS

Pin 3, 4

DALI+

Pin 5, 6

DALI-

2.1.4 DALI Interface and UART Interface

JP8

Interface Signal Name

MCU Pin Assignment

Pin 1

DTX

PC.2

Pin 2

TXD

UART1_TX / PD.3

JP9

Interface Signal Name

MCU Pin Assignment

Pin 1

DRX

PB.0

Pin 2

RXD

UART1_RX / PD.4

2.1.5 Peripherial Interface

JP10

Interface Signal Name

MCU Pin Assignment

Pin 1

CAP0

ECAP_P0 / PC.4

Pin 2

CAP1

ECAP_P1 / PB.1

JP11

Interface Signal Name

MCU Pin Assignment

Pin 1

ADC0_CH2

ADC0_CH2 / PB.2

Pin 2

ADC1_CH0

ADC1_CH0 / PB.4

Pin 3

ADC0_CH4

ADC0_CH4 / PC.1

Pin 4

ADC0_CH3

ADC0_CH3 / PC.0

DALI 2nd Slave

Jul 11, 2019 Page 7of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

3HOW TO START NUVOTON DALI 2nd SLAVE ON THE KEIL μVISION®IDE

Keil μVision®IDE Software Download and Install3.1

Please visit the Keil company website (http://www.keil.com) to download the Keil μVision®IDE and

install the RVMDK.

Nuvoton Nu-Link Driver Download and Install3.2

Please visit the Nuvoton company NuMicro®website (http://www.nuvoton.com/NuMicro) to download

“NuMicro®Keil μVision®IDE driver” file. When the Nu-Link driver has been well downloaded, please

unzip the file and execute the “Nu-Link_Keil_Driver.exe” to install the driver.

Hardware Setup

3.3

The hardware setup is shown as Figure 3-1.

Figure 3-1 Hardware Setup

DALI 2nd Slave

Jul 11, 2019 Page 8of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

4HOW TO START NUVOTON DALI 2nd SLAVE ON THE IAR EMBEDDED

WORKBENCH

IAR Embedded Workbench Software Download and Install4.1

Please connect to IAR company website (http://www.iar.com) to download the IAR Embedded

Workbench and install the EWARM.

Nuvoton Nu-Link Driver Download and Install4.2

Please visit the Nuvoton company NuMicro®website (http://www.nuvoton.com/NuMicro ) to download

the “NuMicro®IAR EWARM Driver” file. When the Nu-Link driver has been well downloaded, please

unzip the file and execute the “Nu-Link_IAR_Driver.exe” to install the driver.

Hardware Setup4.3

The hardware setup is shown as Figure 4-1.

Figure 4-1 Hardware Setup

DALI 2nd Slave

Jul 11, 2019 Page 9of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

5NUVOTON DALI 2nd SLAVE QUICK START

Hardware Setup5.1

Connect the Nuvoton DALI 2nd Slave. DALI Bus interface JP4 or JP5 to the DALI control device as

Figure 5-1. The DALI Bus can be connected at any position.

Connect the power supply 5 V to the Nuvoton DALI 2nd Slave JP1 or JP2 as Figure 5-1.

It is recommanded to use Nuvoton DALI Master as the DALI control device as Figure 5-2.

Figure 5-1 Connections of DALI Bus and Power Supply

Figure 5-2 Nuvoton DALI Master with Nuvoton DALI 2nd Slave

DALI 2nd Slave

Jul 11, 2019 Page 10 of 18 Rev 1.00

DALI 2nd SLAVE USER MANUAL

Initialisation5.2

Use the software tool - DALI Controller to do the initialisation. The DALI Controller can auto-detect the

Nuvoton DALI Master through USB interface. Choose “New Initialization” to discover all control gear

on the line. It will assign particular short address to each control gear as Figure 5-3.

Figure 5-3 Initialisation

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Nuvoton Microcontrollore

Nuvoton

Nuvoton NuMicro M031 Series Manuale utente

Nuvoton

Nuvoton NuMicro series Manuale utente

Nuvoton

Nuvoton NuMaker-M031SD Manuale utente

Nuvoton

Nuvoton NuMicro NuMaker-HMI-M2354 Manuale utente

Nuvoton

Nuvoton NuMaker M032BTAI Manuale utente

Nuvoton

Nuvoton Numicro NuMaker-NUC1311L Manuale utente

Nuvoton

Nuvoton NuTiny-SDK-NUC123 Manuale utente

Nuvoton

Nuvoton NuMicro M483 Series Manuale utente

Nuvoton

Nuvoton NuMicro M480 Series Manuale utente

Nuvoton

Nuvoton NuMaker-MS51PC Manuale utente

Nuvoton

Nuvoton NuMicro series Manuale utente

Nuvoton

Nuvoton 1T 8051 Manuale utente

Nuvoton

Nuvoton NuMicro M031 Series Manuale utente

Nuvoton

Nuvoton NuMaker-M031TC Manuale utente

Nuvoton

Nuvoton emWin NUC126 Manuale utente

Nuvoton

Nuvoton ARM Cortex-M NuMicro NUC472 Series Manuale utente

Nuvoton

Nuvoton NuMicro M032 Series Manuale utente

Nuvoton

Nuvoton NuMicro NUC442 Series Manuale del prodotto

Nuvoton

Nuvoton NuMicro M032 Series Manuale utente

Nuvoton

Nuvoton NuMicro series Manuale utente

Nuvoton

Nuvoton NuMicro NUC100 Series Manuale utente

Nuvoton

Nuvoton Nu-LB-M051 Manuale utente

Nuvoton

Nuvoton NuMicro ISP Manuale utente

Nuvoton

Nuvoton NuMicro NuTiny-SDK-NANO130 Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente

Silicon Laboratories

Silicon Laboratories C8051F800 Manuale utente