NXP Semiconductors Android i.MX 8M Mini Manuale utente

1 Overview

This document guides you through the processes of

downloading and running this release package. It only

explains how to download and run the default release image

with default configuration. For details on using the release

package, see the Android™ User's Guide (AUG) included in

this release package.

2 Hardware Requirements

The hardware requirements for using this release package are

as follows:

Supported system-on-chips (SoCs):

• i.MX 8M Mini

• i.MX 8M Quad

• i.MX 8QuadMax

• i.MX 8QuadXPlus

Supported boards:

• EVK board and Platform

• MEK board and Platform

NXP Semiconductors Document Number: AQSUG

Rev. P9.0.0_2.0.0-ga, 04/2019

Android™ Quick Start Guide

Contents

1 Overview....................................................................1

2 Hardware Requirements............................................ 1

3 Working with the i.MX 8M Mini EVK

Board......................................................................... 2

4 Working with the i.MX 8M Quad EVK

Board......................................................................... 9

5 Working with the i.MX 8QuadMax

MEK Board.............................................. ...............18

6 Working with the i.MX 8QuadXPlus

MEK Board............................................................. 25

7 Revision History......................... ............................ 30

3 Working with the i.MX 8M Mini EVK Board

3.1 Board hardware

The figures below show the different components of the i.MX 8M Mini EVK board.

Figure 1. i.MX 8M Mini EVK board

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

2 NXP Semiconductors

Figure 2. i.MX 8M Mini EVK with audio board

Figure 3. i.MX 8M Mini SAS cable with DSI-to-HDMI adapter

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

NXP Semiconductors 3

Figure 4. i.MX MIPI panel

Figure 5. i.MX MIPI camera

NOTE

• To test the MIPI-DSI to HDMI display, use the i.MX mini SAS cable to connect

the DSI-to-HDMI adapter to the "HDMI DSI" port.

• To test the MIPI panel display, conect the i.MX MIPI panel to the "HDMI DSI"

port.

• To test the camera, connect the i.MX CSI MIPI Camera to the "Camera" port.

• The QCOM 1PJ Wi-Fi/Bluetooth module is used on the i.MX 8M Mini EVK

LPDDR4 Board.

• The BCM 1MW Wi-Fi/Bluetooth module is used on the i.MX 8M Mini EVK

DDR4 Board.

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

4 NXP Semiconductors

3.2 Board images

The table below describes the location in the board partitions of the software images in android_p9.0.0_2.0.0-

ga_image_8mmevk.tar.gz.

Table 1. Board images

Image name Download target

/u-boot-imx8mm.imx 33 KB offset of MMC for a board with LPDDR4 on it.

/u-boot-imx8mm-ddr4.imx 33 KB offset of MMC for a board with DDR4 on it.

/u-boot-imx8mm-evk-uuu.imx Bootloader used by UUU for the i.MX 8M Mini board with

LPDDR4 on it. It is not flashed to MMC.

/u-boot-imx8mm-ddr4-evk-uuu.imx Bootloader used by UUU for the i.MX 8M Mini board with

DDR4 on it. It is not flashed to MMC.

/imx8mm_m4_demo.img 5120 KB offset of MMC.

/partition-table.img 0 offset of MMC. If the actually size of the SD card is larger

than 13 GB, use the default partition-table.img.

/partition-table-7GB.img 0 offset of MMC. If the actually size of the SD card is larger

than 7 GB, use this image as partition-table.img.

/partition-table-28GB.img 0 offset of MMC. If the actually size of the SD card is larger

than 28 GB, use this image as partition-table.img.

/boot.img boot_a and boot_b partitions.

/vbmeta-imx8mm.img vbmeta_a and vbmeta_b partitions to support LPDDR4 and

MIPI-to-HDMI output and Direct Stream Digital (DSD)

playback.

/vbmeta-imx8mm-ddr4.img vbmeta_a and vbmeta_b partitions to support DDR4 and

MIPI-to-HDMI output.

/vbmeta-imx8mm-m4.img vbmeta_a and vbmeta_b partitions to support LPDDR4,

MIPI-to-HDMI output, and audio playback based on Cortex-

M4 FreeRTOS.

/vbmeta-imx8mm-mipi-panel.img vbmeta_a and vbmeta_b partitions to support LPDDR4 and

MIPI panel output.

/system.img system_a and system_b partitions.

/vendor.img vendor_a and vendor_b partitions.

/dtbo-imx8mm.img dtbo_a and dtbo_b paritions to support LPDDR4, MIPI-to-

HDMI output, and DSD playback.

/dtbo-imx8mm-ddr4.img dtbo_a and dtbo_b paritions to support DDR4 and MIPI-to-

HDMI output.

/dtbo-imx8mm-m4.img dtbo_a and dtbo_b paritions to support LPDDR4, MIPI-to-

HDMI output, and audio playback based Cortex-M4

FreeRTOS.

/dtbo-imx8mm-mipi-panel.img dtbo_a and dtbo_b paritions to support LPDDR4 and MIPI

panel output.

3.3 Flashing board images

The board image files can be flashed into the target board using Universal Update Utility (UUU).

For the UUU binary file, download it from github: uuu release page on github.

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

NXP Semiconductors 5

To achieve more flexibility, two script files are provided to invoke UUU to automatically flash all Android images.

• uuu_imx_android_flash.sh for Linux OS

• uuu_imx_android_flash.bat for Windows OS

For this release, these two scripts are validated on UUU 1.2.91 version. Download corresponding version from github:

• For Linux OS, download the file named "uuu".

• For Windows OS, download the file named "uuu.exe".

Because the two script files will direclty invoke UUU, make sure that UUU is in a path contained by the system environment

variable of "PATH".

Perform the following steps to download the board images:

1. Download the UUU binary file from github as described before. Install UUU into a directory contained by the system

environment variable of "PATH".

2. Make the board enter serial download mode.

• For Rev. B boards, change the first two bits of board's sw1101 to 10 (from 1-2 bit) to enter serial download

mode.

• For Rev. C boards, change the first four bits of board's sw1101 to 1010 (from 1-4 bit) to enter serial download

mode.

3. Power on the board. Use the USB cable on the board OTG port to connect your PC with the board.

4. Decompress release_package/android_p9.0.0_2.0.0-ga_image_8mmevk.tar.gz, which contains the image files and

uuu_imx_android_flash tool.

5. Execute the uuu_imx_android_flash tool to flash images.

The uuu_imx_android_flash tool can be executed with options to get help information and specify the images to be

flashed. For i.MX 8M Mini board, related options are described as follows

Table 2. Options for uuu_imx_android_flash

tool

Option Description

-h Displays the help information of this tool.

-f

soc_name

Specifies the SoC information. For i.MX 8M Mini, it

should be "imx8mm". This option is mandatory.

-a Only flashes slot a. If this option and "-b" option are

not used, slots a and b are both flashed.

-b Only flashes slot b. If this option and "-a" option are

not used, slots a and b are both flashed.

-c card_size Specifies which partition table image file to flash. For

i.MX 8M Mini, it can be followed with "7" or "28". If

this option is not used, default "partition-table.img" is

flashed.

-m Flashes Cortex-M4 image. If this option is not used,

Cortex-M4 image is not flashed.

-d

dev

Specifies some images with "dev" in its name. For

i.MX 8M Mini, it can be "m4", "mipi-panel", "ddr4". If

this option is not used, default dtbo and vbmeta

images are flashed.

-e Erases user data after images are flashed.

-D

directory

Specifies the directory in which there are the images

to be flashed. If this option is not used, images in the

current working directory are flashed.

Table continues on the next page...

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

6 NXP Semiconductors

Table 2. Options for uuu_imx_android_flash tool

(continued)

Option Description

-t target_dev Specifies the target device. For i.MX 8M Mini, it can

be "emmc" and "sd". If this option is not used,

images are flashed to eMMC.

-daemon Run UUU in Daemon mode. This option is used to

flash multiple boards of the same type.

-i If the script is executed with this option, no images

will be flashed. The script loads U-Boot to RAM and

executes to fastboot mode. this option is used for

development.

Obviously, "-m" and "-d m4" should be used together.

• On Linux system, open the shell terminal. For example, you can execute a command as follows:

> sudo ./uuu_imx_android_flash.sh -f imx8mm -a -e

• On Windows system, open the command line interface in administrator mode. The corresponding command is as

follows:

> .\uuu_imx_android_flash.bat -f imx8mm -a -e

When the command above is executed, the default images will be flashed into eMMC slot a for i.MX 8M Mini.

NOTE

• To flash the SD card, execute the tool with "-t sd". To flash eMMC, it does

not need to use -t option.

• If your SD card is 16 GB or the on-board eMMC is used as the boot device, it

does not need to use -c option.

• If your SD card is 32 GB, execute the tool with "-c 28".

• If your SD card is 8 GB, execute the tool with "-c 7".

• To test MIPI-DSI to HDMI output with LPDDR4 on board, it does not need

to use -d option.

• To test MIPI-DSI to HDMI output with DDR4 on board, execute the tool

with "-d ddr4".

• To test MIPI panel output with LPDDR4 on board, execute the tool with "-d

mipi-panel".

• To test MIPI-to-HDMI output and audio playback based on Cortex-M4

FreeRTOS with LPDDR4 on board, execute the tool with "-m" and "-d m4".

• uuu_imx_android_flash.bat generates a temporary file under the current

working directory. Make sure you have Write permission under the current

working directory.

• If uuu_imx_android_flash.bat is used to flash images on a remote server

through samba, you need to map the remote resource to the local environment

first. Take the following command as an example:

> net use z: \\10.193.108.179\daily_images

"z" in the command represents an available drive letter. It can be other

available drive letter.

6. Wait for the uuu_imx_android_flash execution to complete. If there is not any error, you will get information on the

command window indicating that images are already flashed.

7. Power off the board.

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

NXP Semiconductors 7

8. Change boot device as eMMC or SD card.

For Rev. B boards:

• Change sw1101 to 01110010 and change sw1102 to 00101010 if you want to boot from eMMC.

• Change sw1101 to 01000110 and change sw1102 to 00110100 if you want to boot from SD card.

For Rev. C boards:

• Change sw1101 to 0110110010 and change sw1102 to 0001010100 if you want to boot from eMMC.

• Change sw1101 to 0110110010 and change sw1102 to 0001101000 if you want to boot from SD card.

3.4 Booting

After downloading the images, reboot the board using the power on/off switch.

3.4.1 Booting with Single MIPI-to-HDMI or MIPI panel display

In the U-Boot prompt, set the U-Boot environment variables as follows:

• i.MX 8M Mini EVK LPDDR4 Board:

U-Boot > setenv bootargs console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200

init=/init androidboot.console=ttymxc1 consoleblank=0 androidboot.hardware=freescale

cma=800M androidboot.primary_display=imx-drm firmware_class.path=/vendor/firmware

transparent_hugepage=never androidboot.wifivendor=qca androidboot.wificountrycode=CN

U-Boot > saveenv

• i.MX 8M Mini EVK DDR4 Board:

U-Boot > setenv bootargs console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200

init=/init androidboot.console=ttymxc1 consoleblank=0 androidboot.hardware=freescale

cma=800M androidboot.primary_display=imx-drm firmware_class.path=/vendor/firmware

transparent_hugepage=never androidboot.wifivendor=bcm androidboot.wificountrycode=CN

U-Boot > saveenv

With the settings above, the Android platform does not start the shell console. To disable selinux, append

"androidboot.selinux=permissive" to the U-Boot's bootargs. Boot environment variables are as follows:

U-Boot > setenv append_bootargs androidboot.selinux=permissive

U-Boot > saveenv

3.4.2 Booting with Single MIPI-to-HDMI display and audio playback

based on Cortex-M4 FreeRTOS

In the U-Boot prompt, set the U-Boot environment variables as follows:

• i.MX 8M Mini EVK LPDDR4 Board:

U-Boot > setenv bootargs console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200

init=/init androidboot.console=ttymxc1 consoleblank=0 androidboot.hardware=freescale

cma=800M androidboot.primary_display=imx-drm firmware_class.path=/vendor/firmware

transparent_hugepage=never androidboot.wifivendor=qca androidboot.wificountrycode=CN

U-Boot > setenv bootcmd "bootmcu && boota mmc0" # for SD boot

U-Boot > setenv bootcmd "bootmcu && boota mmc1" # for emmc boot

U-Boot > saveenv

• i.MX 8M Mini EVK DDR4 Board:

U-Boot > setenv bootargs console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200

init=/init androidboot.console=ttymxc1 consoleblank=0 androidboot.hardware=freescale

cma=800M androidboot.primary_display=imx-drm firmware_class.path=/vendor/firmware

transparent_hugepage=never androidboot.wifivendor=bcm androidboot.wificountrycode=CN

Working with the i.MX 8M Mini EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

8 NXP Semiconductors

U-Boot > setenv bootcmd "bootmcu && boota mmc0" # for SD boot

U-Boot > setenv bootcmd "bootmcu && boota mmc1" # for emmc boot

U-Boot > saveenv

NOTE

To use other boot images, do not add "bootmcu" to "bootcmd". The following command

can recover bootcmd:

U-Boot > setenv bootcmd "boota mmc0" # for SD boot

U-Boot > setenv bootcmd "boota mmc1" # for emmc boot

U-Boot > saveenv

With the settings above, the Android platform does not start the shell console. To disable selinux, append

"androidboot.selinux=permissive" to the U-Boot's bootargs. Boot environment variables are as follows:

U-Boot > setenv append_bootargs androidboot.selinux=permissive

U-Boot > saveenv

3.5 Board reboot

After you have completed download and setup, reboot the board and wait for the Android platform to boot up.

Figure 6. Android Pie image

4Working with the i.MX 8M Quad EVK Board

Working with the i.MX 8M Quad EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

NXP Semiconductors 9

4.1 Board hardware

The figures below show the different components of the i.MX 8M Quad EVK board.

Figure 7. i.MX 8M Quad EVK board

Working with the i.MX 8M Quad EVK Board

Android™ Quick Start Guide, Rev. P9.0.0_2.0.0-ga, 04/2019

10 NXP Semiconductors

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NXP Semiconductors Hardware per computer

NXP Semiconductors

NXP Semiconductors MCU-SMHMI-HDUG Manuale utente

NXP Semiconductors

NXP Semiconductors UM11620 Manuale utente

NXP Semiconductors

NXP Semiconductors K32W061 Manuale utente

NXP Semiconductors

NXP Semiconductors i.MX 6SoloX SABRE-SDB Manuale utente

NXP Semiconductors

NXP Semiconductors OM13489 Manuale utente

NXP Semiconductors

NXP Semiconductors i.MX 8M Mini EVK Manuale utente

NXP Semiconductors

NXP Semiconductors QSG ADC1x13D+ECP3 DB Manuale utente

NXP Semiconductors

NXP Semiconductors freescale MED-GLU Manuale utente

NXP Semiconductors

NXP Semiconductors JN516x Manuale utente

NXP Semiconductors

NXP Semiconductors HRPNUG Manuale utente

NXP Semiconductors

NXP Semiconductors QorIQ T2080 Manuale utente

NXP Semiconductors

NXP Semiconductors MCIMX8QM-CPU Manuale utente

NXP Semiconductors

NXP Semiconductors FRDM665SPIEVB Manuale utente

NXP Semiconductors

NXP Semiconductors MCIMX7SABRE Manuale utente

NXP Semiconductors

NXP Semiconductors i.MX 8M Manuale di installazione

NXP Semiconductors

NXP Semiconductors UM11650 Manuale utente

NXP Semiconductors

NXP Semiconductors S32G-VNP-EVB3 Manuale utente

NXP Semiconductors

NXP Semiconductors JN5179 Manuale utente

NXP Semiconductors

NXP Semiconductors LPCXpresso54608 Manuale utente

NXP Semiconductors

NXP Semiconductors MCXN 4 Series Guida

NXP Semiconductors

NXP Semiconductors MR-CANHUBK344 Istruzioni per l’uso

NXP Semiconductors

NXP Semiconductors FRDM-MCXN947 Manuale utente

NXP Semiconductors

NXP Semiconductors PCA9555 Manuale operativo

NXP Semiconductors

NXP Semiconductors KW45B41Z-EVK Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente