NXP Semiconductors S32R27 Guida

1 Introduction

The S32R is a 32-bit heterogeneous multi-core microcontroller

family primarily intended for use in computationally intensive

automotive RADAR applications. The device family

incorporates Power Architecture®cores arranged as two

independent e200z7260 for general computation and the

S32R274 device also features an e200z420 core with an

e200z419 checker core running in delayed lockstep

configuration for safety-critical and housekeeping tasks. The

family integrates high-performance signal processing features

designed to support sophisticated automotive RADAR

applications, and the S32R274 also integrates high accuracy

analog features to further enhance it's ability to interface with

a wide range of RADAR RF devices.

This application note illustrates the S32R family power supply

options and details the external circuitry required for power

supplies, oscillator connections, and supply decoupling pins. It

also discusses configuration options for clock, reset, ADC

modules and the RADAR analog front-end, as well as

recommended debug and peripheral communication

connections (including MIPI-CSI2) and other major external

hardware required for the device.

The S32R family requires multiple external power supplies to

operate. The main cores internal logic requires a 1.25 V power

supply. This can be supplied from an external source or on

some devices this can alternatively be provided by an internal

DC-DC regulator that requires a dedicated supply. 3.3 V is

NXP Semiconductors Document Number: AN5251

Application Note Rev. 1, 04/2018

S32R27/37 Hardware Design Guide

by: NXP Semiconductors

Contents

1 Introduction.............................. .............................. 1

2 S32R family package options

overview..................................................................2

3 Power supply...........................................................3

4 Clock configuration...............................................15

5 Device reset configuration............... .....................17

6 Recommended debug connectors and

connector pin-out definitions.................... ............ 18

7 ADC overview........................... ........................... 22

8 RADAR analog front end..................................... 23

9 Example communication peripheral

connections.......................................... ................. 29

10 High speed layout considerations..........................48

A Revision History................................................... 49

required for the general purpose I/O, flash memory, analog front-end, external communications interfaces, and on-chip SAR

analog to digital converter.

2 S32R family package options overview

The S32R family is available in multiple device and package options that are suited to development, debug and commercial

production.

Table 1. S32R package description

Device Package Description

S32R274 257 Map ball grid array (MAPBGA) Full support for all device modules and features

including JTAG and Nexus High Speed Aurora Trace

debug interfaces.

S32R372 257 Map ball grid array (MAPBGA) Full support for all device modules and features

including JTAG and Nexus High Speed Aurora Trace

debug interfaces. Pin compatible with S32R274,

although with reduced feature set. See Table 3 below

for details.

S32R372 141 Map ball grid array (MAPBGA) Reduced support for some device modules and

features. See Table 3 for details of reduced features

The table below shows the physical dimensions of the packages. See the device data sheet for complete package dimensions

and ball placement. Drawings are also available on nxp.com, search for the case outline number shown in Table 2.

Table 2. Package sizes

Device Package Physical Size Case Outline Number Pitch

S32R274 257 MAPBGA 14 x 14 mm 98ASA00081D 0.8 mm

S32R372 257 MAPBGA 14 x 14 mm 98ASA00081D 0.8 mm

S32R372 141 MAPBGA 10 x 10 mm 84ASA00768D 0.65 mm

The table below shows the main differences between the S32R family, including the different available packages. This list

only references the differences that have a hardware impact. For full details of all differences between the various devices

please see the relevant device reference manuals.

Table 3. Feature Differences Between Packages

Feature S32R274 S32R372 257 MAPBGA S32R372 141 MAPBGA

SD-ADC 4x SD-ADC None None

DAC Yes None None

MIPI CSI2 4 Lanes + Clock 2 Lanes + Clock 2 Lanes + Clock

Ethernet Yes, up to RGMII interface. None None

Wave Generator Module

(WGM)

Yes None None

LINFlexD Yes, 1 module Yes, 1 module None

FlexPWM 1 module, 12 channels 1 module, 12 channels 1 module, 11 channels

Table continues on the next page...

S32R family package options overview

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

2 NXP Semiconductors

Table 3. Feature Differences Between Packages (continued)

Feature S32R274 S32R372 257 MAPBGA S32R372 141 MAPBGA

SPI 2 modules 2 modules 2 modules, some chip selects not

available. See device muxing

sheet for details.

IIC 2 modules 2 modules 1 module (IIC1 only).

Serial Inter-Processor

Interface (SIPI)

Yes None None

System Timer Module

(STM)

3 modules x 4 channels 2 modules x 4 channels 2 modules x 4 channels

System Timer Module

(STM)

eTimer_0: 6 channels,

eTimer_1: 6 channels

eTimer_1:6 channels eTimer_1:5 channels

FlexRay 1 module None None

FlexCAN 1x FlexCAN, 2x FlexCAN-

2x FlexCAN-FD 2x FlexCAN-FD

Device Power Supply Internal or External

regulation modes

Internal or External regulation

modes

External regulation mode only

3 Power supply

The S32R family of microcontroller units have a robust power management infrastructure that enables applications to select

among various user modes and to monitor internal voltages for high- and low-voltage conditions. The monitoring capability

is also used to ensure supply voltages and internal voltages are within the required operating ranges before the

microcontroller can exit the reset state and enter operation.

The microcontroller offers a DC-DC voltage regulator function as part of the power management controller (PMC) module. 1

This regulator can be used to supply the digital low voltage required for the internal logic and other low voltage supplies. The

device can be configured to use either this internal regulation mode or an external 1.25 V regulated power supply to provide

the core voltage. The standard configuration utilizes the internal DC-DC voltage regulator, with the following external supply

voltages:

• 3.3 V for main general purpose I/O, SAR ADC supply and reference, JTAG debug interface, flash memory supply

voltage and external communication interfaces (Ethernet, FlexRay, etc.)

• 3.13 - 5.5 V (required) for the internal DC-DC voltage regulator which supplies 1.25 V for the internal logic, PLL

circuits and low voltage/Nexus Aurora I/O, and MIPI-CSI2.

Detailed information on the power management configurations can be found in the Power management controller section.

1. Not available on the S32R372 141BGA Package.

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

NXP Semiconductors 3

3.1 Power supply signals and decoupling

Table 4 lists all MCU power domains with corresponding pin names. Depending on the power management configuration,

some of the supplies below may not require an external power source. The power management configuration is detailed in

Power management controller.

Table 4. MCU power supply pins

Domain name Supply

Voltage

Description

VDD_LV_CORE 1.25 V Low-voltage supply for core logic

VDD_HV_IOx 3.3 V High-voltage supply for general purpose I/O

VDD_HV_RAW 3.3 V High-voltage, high fidelity supply for analog front-end block

VDD_HV_DAC 13.3 V High-voltage supply for DAC module in analog front-end

VDD_HV_ADC 3.3 V Voltage supply for SAR ADC module

VDD_HV_ADCREF0/2 23.3 V Voltage reference for SAR ADC 0/2

VDD_HV_FLA 3.3 V Voltage supply for flash memory

VDD_HV_PMU 3.3 V Voltage supply for power management unit

VDD_HV_IO_PWM 13.3 V Voltage supply for PWM IO

VDD_HV_REG3V8 13.13 V - 5.5 V3Voltage supply for internal DC-DC voltage regulator

VDD_LV_LFASTPLL41.25 V Voltage supply for DigiRF (SIPI/LFAST) PLL

VDD_LV_IO_AURORA51.25 V Voltage supply for Nexus Aurora I/O

VDD_LV_PLL0 1.25 V Voltage supply for system PLL

VDD_LV_IO 1.25 V Low voltage supply for general purpose I/O

VDD_LV_DPHY61.25 V Low voltage supply for MIPI-CSI2 DHPY

1. Not present on S32R372 141MAPBGA Package

2. To ensure optimum SAR ADC performance it is recommended to have a ground plane below the VDD_HV_ADCREF0/2

traces.

3. Internal regulation mode. When using external regulation mode, this domain can be tied to VDD_HV_PMU

4. The naming convention VDD_LV_LFASTPLL is equal to VDD_LV_DRFPLL. Not present on S32R372 141MAPBGA

Package

5. VDD_LV_IO_AURORA must be connected to the same voltage supply as VDD_LV_CORE. The supplies must be brought

up simultaneously.

6. Can be supplied from VDD_LV_CORE supply with filtering as recommended below.

Some of the supplies can be powered with different supply voltages. The internal voltage regulator supply,

VDD_HV_REG3V8, can be supplied with a voltage between 3.13 V and 5.5 V. See the device data sheet for specific

information and to learn what voltage ranges can be safely connected to the power pins.

Table 5 shows all power domains and the suggested decoupling and/or filter capacitors for their corresponding pins. These

values are provided as a guideline and will vary depending on the application and capability of the power supplies used.

The decoupling capacitors must be placed as close as possible to the MCU supply pins, with priority given to those with the

smallest capacitance value.

Table 5. Supply pin decoupling capacitors

Domain name Supply

Voltage

Minimum Decoupling Capacitors

VDD _LV_CORE 1.25 V 0.1 μF x 16, 4.7 μF x 4, 10 μF x 2 (40 μF total)1

VDD_HV_IOx 3.3 V 2 x 0.1 μF for each VDD_HV_IO supply2

Table continues on the next page...

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

4 NXP Semiconductors

Table 5. Supply pin decoupling capacitors (continued)

Domain name Supply

Voltage

Minimum Decoupling Capacitors

VDD_HV_RAW 3.3 V 0.1 μF, 1 μF

VDD_HV_DAC 33.3 V 1000 pF, 0.1 μF, 1 μF

VDD_HV_ADC 3.3 V 0.1 μF, 1 μF

VDD_HV_ADCREF0/2 3.3 V 0.01 μF, 1 μF

VDD_HV_IO_PWM 33.3 V 2x 0.1 μF for each supply

VDD_HV_FLA 3.3 V 0.1 μF, 1000 pF

VDD_HV_PMU 3.3 V 100 nF, 4.7 μF

VDD_HV_REG3V8 33.13 V - 5.5

1 μF Ceramic4

VDD_LV_DRFPLL 31.25 V 1000 pF, 0.1 μF, 1 μF, 0.01 μF

VDD_LV_IO_AURORA 1.25 V 0.1 μF, 1 μF

VDD_LV_PLL0 1.25 V 1000 pF, 0.1 μF, 1μF, 0.01 μF

VDD_LV_DPHY 1.25 V Ferrite bead, >5 μF, 100 nF, 1000 pF

1. When using internal regulation mode, assure that the total capacitance (accounting for temperature variations) never falls

below 40 μF

2. External capacitors for the IO pins are dependent on the application.

3. Not present on S32R372 141BGA Package

4. When device is configured in external regulation mode and supply is connected to VDD_HV_PMU. For internal regulation

mode see SMPS external component configuration

The device has several pins for the connection to external decoupling capacitors for the analog front-end. Details of these can

be found in RADAR analog front end

3.2 Decoupling capacitors layout priority

When trade-offs must be made in the schematic layout, it is important to ensure that the highest priority supplies have

decoupling capacitors placed as closely as possible to the MCU. The list below outlines the recommended order of the

supplies from highest to lowest priority in terms of their importance for decoupling.

1. VDD_HV_RAW & VDD_HV_DAC

2. VDD_HV_ADCREF0/2

3. VDD_HV_ADC

4. VDD_LV_PLL0

5. VDD_LV_DPHY

6. VDD_LV_CORE

7. VDD_LV_AURORA

8. VDD_HV_PMU

9. VDD_HV_FLA

10. VDD_LV_LFASTPLL2

11. VDD_LV_IO

12. VDD_HV_PWM3

13. VDD_HV_IO

2. Not present on S32R372 141MAPBGA Package

3. Not present on S32R372 141MAPBGA Package

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

NXP Semiconductors 5

Highest priority is given to the high-fidelity analog front end supplies VDD_HV_RAW and VDD_HV_DAC, as their

decoupling must be prioritized to maintain analog signal integrity. VDD_HV_ADRREF0, VDD_HV_ADREF1, and

VDD_HV_ADC is the SAR analog-to-digital converters reference and power supply decoupling. Clean supplies are vital to

ensure that the highest accuracy is achieved with the ADCs. The supply for the system PLL is prioritized as this helps to

ensure reliable and stable operation from the internal PLL circuit.

Medium priority is given to VDD_LV_CORE, VDD_LV_DRFPLL, VDD_LV_AURORA, VDD_HV_PMU,

VDD_LV_DPHY and VDD_HV_FLA. VDD_LV_CORE is the main supply for the on-chip digital logic and this is

prioritized as it affects the largest amount of logic on the device. VDD_LV_AURORA powers the high speed Nexus Aurora

pins and noise on this domain would affect the quality of the output. VDD_HV_PMU is the power management unit supply

and VDD_LV_DPHY is the MIPI-CSI2 DPHY supply. The MIPI-CSI2 DPHY is a high speed module which requires

minimal noise in order to acheive the specified performance levels. VDD_HV_FLA is the input supply for the flash memory.

A good supply to the flash memory ensures reliable flash programming and erasing.

VDD_LV_LFASTPLL powers the PLL for the LFAST/SIPI communication interface. 4VDD_HV_IO, VDD_HV_PWM,

and VDD_LV_IO drive GPIO and other external communication interfaces. Although it is still important that these supplies

have a clean power signal, the hardware they power is less affected by noise and they are considered of lower priority.

When completing the layout of decoupling capacitors care should be taken to reduce the volume of the space in the

transmission line between the device and the capacitor, which results in faster response to energy requests from the device.

The capacitor should always be the closest to the device so that the energy comes from the capacitor and not from the power

trace, as illustrated in the figure below.

Figure 1. Decoupling capacitor placement recommendation

3.3 Power management controller

The S32R family has a dedicated module for configuration and monitoring of power supplies, enable signals, internal

component trimming, and power-on reset generation. The Power Management Controller (PMC) consists of an analog block

and a supporting digital interface that provides control over the analog components. The PMC chapter in the device reference

manual explores the digital block in depth.

4. This interface is not present on the S32R372 device, but the supply name remains the same for the 257MAPBGA

package to avoid confusion, and is not present on the 141MAPBGA package.

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

6 NXP Semiconductors

NOTE

This document will focus on the external hardware and connections concerned with the

PMC analog block.

3.3.1 Core supply options

The S32R family offers two options for supplying the 1.25 V used by the core and other low-voltage digital power domains.

• Internal voltage regulation mode, using the integrated DC-DC voltage regulator (VREG)5

• External voltage regulation mode using an externally regulated 1.25 V supply

The input pin VREG_SEL allows selection between internal and external regulation modes, the function of this input is

described in the table below.6

Table 6. VREG_SEL input signal

Input Level Core Supply Mode

High (3.3 V) Internal regulation mode

Low (GND) External regulation mode

The PMC has an internal voltage regulator function that uses a switched-mode power supply (SMPS) circuit to supply the

1.25 V required by the internal core logic, VDD_LV_CORE and the other low-voltage digital supplies

(VDD_LV_AURORA, VDD_LV_PLL0, VDD_LV_DPHY and VDD_LV_IO). The regulator requires the support of

external circuitry detailed in SMPS external component configuration. This configuration is an asynchronous buck regulator

with nominal switching frequency of 1 MHz. The switching frequency may be modulated to improve the EMI performance

of the device, further information on this feature can be found in the PMC chapter in the device reference manual.

VREG_SEL is part of a collection of I/O signals that relate to the VREG operation mode. The other pins are mentioned in the

table below.

Table 7. PMC Voltage regulator signals

Signal Name Direction VREG Enabled (Internal Mode) VREG Disabled (External Mode)

VREG_POR_B Input External power-on reset. If not used it is

recommended to be externally pulled up

to 3.3 V, but can be left floating.

Internally pulled up to 3.3 V.

Power-on reset (POR) input. Used by

external circuitry to trigger a POR or hold

device in reset state. Should be used to

hold device in reset until supplies are

within the ranges described in the device

data sheet.

VREG_ISENS1Input Current sense input to internal regulator Not used. Connect to VDD_LV_CORE

VREG_SWP1Output Output from internal VREG. Controls the

gate of the external switching PMOS

transistor 2

Not used, can be left floating. Internally

pulled up, do not connect to GND.

1. Not present on S32R372 141MAPBGA package.

2. If the connection between VREG_SWP and the PMOS gate is broken, the switch may fully turn on. For added protection

against this risk, a 100 Kilo Ohm resistor can be connected between VDD_HV_REG3V8 and the PMOS gate.

5. Not supported on S32R372 141MAPBGA package.

6. VREG_SEL pad is internally bonded to GND on S32R372 141MAPBGA package.

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

NXP Semiconductors 7

3.3.2 Internal voltage regulator supply mode

The standard device configuration for the S32R family 257 MAPBGA packages uses the internal DC-DC voltage regulator to

supply the core voltage and other low-voltage digital supplies. Figure 2 shows all the power supply connections required

when operating in internal voltage regulation mode and also provides guidelines on how to structure the power nets. Values

for the decoupling capacitors shown in the figure are listed in Table 5.

DC-DC

VReg

Board supply 5V -12V

DC-DC

VReg

SWP

SAR ADC

3.3V

low noise

POR

Lin.

VReg

3.3V

low noise

Lin.

VReg Lin.

VReg

POR_B

DC-DC

VReg

AFE

Internal Lin. VRegs

3.3V

low noise

HV_PMU

3.3V

HV_REG_3V8

3.13V - 5.5V

LV_DRFPLL

LV_PLL0

LFAST

PLL

System

PLL

HV_ADCREF0/2

HV_ADC

1.25V

HV_DAC

HV_RAW

LV_IO_AURORA

NEXUS

AURORA

See "SMPS

External

Component

Configuration"

LV_DPHY

MIPI

CSI2

HV_FLA

HV_IOx

ISENS

LV_CORE

1.25V, 1.8A

HV_IO_PWM

Figure 2. Supply connections

The internal regulator requires a dedicated 3.13 V - 5.5 V supply alongside the 3.3 V PMC supply to generate the 1.25 V

digital low voltage. The support of an external PMOS switch circuit is also required, details are given in SMPS external

component configuration. The analog front-end (AFE) requires high-fidelity supplies and careful decoupling to support its

sensitive analog functionality, covered in RADAR analog front end.

Internal regulation mode is enabled by driving the VREG_SEL input high and has the following attributes.

• The PMC internal power-on-reset (POR) and low-voltage/high-voltage detect (LVD/HVD) circuits are enabled by

default.

• The internal POR will keep the device in reset until all the monitored supplies have reached their minimum operation

threshold.

• The internal POR function means that the external POR pin VREG_POR_B is not needed. As such, it is internally

pulled up to the PMC supply voltage. It can be left floating or alternatively connected to 3.3 V.

• VREG_POR_B remains active in internal regulation mode, even though POR is managed internally. If pulled low it

will cause a power-on reset regardless of voltage regulation mode.7

• The internal LVD/HVD circuits are by default enabled to ensure the expected boot-up sequence occurs. More

information on the LVDs/HVDs is available in Low-Voltage (LVD) and High-Voltage Detection (HVD).

• Use a single Linear VREG to supply both VDD_HV_RAW and VDD_HV_DAC. Both supply pins must have the

recommended filtering as described in Table 5 and have separate routes (star route) of roughly equal length to the

Linear VREG.

• Either ramp VDD_HV_IO and VDD_HV_PMC together or ramp VDD_HV_IO before VDD_HV_PMC such that the

two supplies always maintain 100 mV or less difference when using internal regulation mode.

• VDD_HV_IO, VDD_HV_IO_RGMII, VDD_HV_IO_PWM and VDD_HV_IO_LFAST supplies should be treated as a

single supply from a board perspective.

7. VREG_POR_B can be used in internal regulation mode to ensure that the POR sequence is only started when main

power supply reaches a stable regulation point. This can assist in cases where the power supply reaches the

minimum LVD threshold but then drops below the threshold again when loaded, before reaching a stable regulation

point.

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

8 NXP Semiconductors

3.3.3 SMPS external component configuration

When operating in internal voltage regulation mode, an SMPS circuit is required along with the support of external

components in order to minimize noise and maintain a stable supply to guarantee device performance. Special care must be

taken so that the switched regulator does not introduce noise into high-fidelity analog components. The external component

layout is shown in Figure 3.

Figure 3. SMPS external components layout

Table 8 provides recommended values for the external components.

Table 8. External component values

Component Label Recommended Value

M1 SI3443, 2SQ2315

L1 2.2 μH 3A <100 mΩ series resistance (E.g. Bourns SRU8043-2R2Y)

D1 SS8P3L 8A Schottcky diode

R1 24 kΩ

C1 10 μF ceramic

Table continues on the next page...

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

NXP Semiconductors 9

Table 8. External component values (continued)

Component Label Recommended Value

C2 100 nF ceramic

C3 100 nF ceramic (place close to inductor)

C4 10 μF ceramic (place close to inductor)

C5 1 nF ceramic

C6 4x 100 nF + 4x 10 nF ceramic (place close to MCU supply pins)

C7 4x 10 μF ceramic (place close to MCU supply pins)1

C8 100 nF ceramic (place close to MCU supply pins)

C9 1 μF ceramic (place close to MCU supply pins)

1. These are the same capacitors as those listed for VDD_LV_CORE in Table 2

For optimum electro-magnetic interference (EMI) performance, it is critical that the inner and outer loops shown in Figure 3

overlap on the PCB and are made as short as possible. It is highly recommended to have a section of the PCB ground plane

dedicated to making a good connection between the grounds of C1/C2 and C3/C4. This measure will help to ensure that the

loops are made as short as possible.

The role of C1/C2 is to guarantee a low input impedance to the buck converter. In a similar manner, C3/C4 make the

impedance low at the buck converter output. This measure helps reduce the high frequency content of the current passing

through the highlighted branch 'Iload', making it less critical that the buck converter components be placed close to the

VDD/VSS pins of the MCU. However, it is important that capacitors C6 and C7 are placed as closely as possible to the

VDD/VSS pins of the MCU, as they guarantee the low impedance of the core MCU supply and also help to reduce the high

frequency content of the 'Iload' path.

The gate-driver circuitry also forms important current loops that must be minimized (not shown in Figure 3). For that

purpose, C8/C9 must be placed as close as possible to the gate-driver supply pins. The ground connections for C8/C9 must be

made as short as possible to C1/C2. When the PMOS switch is turned on, the high-frequency current that charges the gate

comes from C1/C2, passing through the PMOS gate into the gate-driver pin. That current is carried to the gate-driver VSS pin

returning to C1/C2. This current loop must be made as small as possible.

Conversely, when the PMOS switch is turned off, high-frequency currents enter in the PMOS gate coming from the gate-

driver pin and flows into C1/C2, returning through the ground into C8/C9 and then into the gate-driver supply pin.

Minimizing this second loop area is as critical as the first.

To shield nearby nets from the gate-driver generated noise, it is also recommended that the gate-driver supply pins are used

to shield the VREG_SWP net until it reaches the PMOS switch. Nets on other PCB layer should avoid running parallel to this

net.

The figure below is a circuit schematic showing an example SMPS circuit derived from the above guidelines. For best

performance, use the component values recommended in Table 8.

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

10 NXP Semiconductors

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NXP Semiconductors Microcontrollore

NXP Semiconductors

NXP Semiconductors LPC21 Series Manuale utente

NXP Semiconductors

NXP Semiconductors Freescale TWR-MECH Manuale utente

NXP Semiconductors

NXP Semiconductors MPC5746R Guida

NXP Semiconductors

NXP Semiconductors USB-KW38 Manuale utente

NXP Semiconductors

NXP Semiconductors WPR1500-BUCK Manuale utente

NXP Semiconductors

NXP Semiconductors SE050 Istruzioni per l'installazione e il funzionamento

NXP Semiconductors

NXP Semiconductors ADC1610S Series Manuale utente

NXP Semiconductors

NXP Semiconductors MC68HC16Z1 Manuale utente

NXP Semiconductors

NXP Semiconductors MCIMX6UL-EVK Manuale utente

NXP Semiconductors

NXP Semiconductors Freescale Semiconductor MPC8569E-MDS-PB Manuale utente

NXP Semiconductors

NXP Semiconductors LPC43Sxx Manuale utente

NXP Semiconductors

NXP Semiconductors LPC5411 Series Manuale operativo

NXP Semiconductors

NXP Semiconductors QN9080 Manuale utente

NXP Semiconductors

NXP Semiconductors MPC5748G Low Cost EVB Manuale utente

NXP Semiconductors

NXP Semiconductors SLN-VIZN3D-IOT Manuale utente

NXP Semiconductors

NXP Semiconductors OM2NTA5KIT Manuale utente

NXP Semiconductors

NXP Semiconductors FRDM-KW41Z Manuale utente

NXP Semiconductors

NXP Semiconductors A71CL Manuale utente

NXP Semiconductors

NXP Semiconductors LPC824M201JHI33 Manuale utente

NXP Semiconductors

NXP Semiconductors freescale semiconductor ColdFire MCF51CN128... Manuale utente

NXP Semiconductors

NXP Semiconductors MKL27Z128VFM4 Manuale utente

NXP Semiconductors

NXP Semiconductors TWR-KM34Z50M Manuale utente

NXP Semiconductors

NXP Semiconductors MRF300AN Manuale utente

NXP Semiconductors

NXP Semiconductors UM10741 Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente