Observint BLK-CPD227VH Manuale utente

1BLK-CPD227VH_CQ

9/26/12

Base

Camera

module

L-wrench

Dome

Base

cable

access

Mounting

screws (2)

Camera

module

screws (2)

Dome

screws (3)

Side cable

access, cap

Dome

retention

cable

Drop

cable

4. Select the best fasteners to secure the base to the mounting surface. Screws provided with the

camera are adequate many surface types.

5. Drill holes in the mounting surface as required for the mounting screws (wall inserts, etc.), and the

cables, if needed.

6. Route the video / power extension cables from your monitoring equipment into the camera base.

Note that the extension cable connectors are usually dierent at each end.

7. Connect the video / power extension cables to the drop cable inside the base cavity.

8. Reattach the camera module to the based using the two screws removed earlier.

9. Connect the video / power extension cable to your camera, then connect the other end to a video

monitor and 12 Vdc or 24 Vac power source. NOTE: 1) The camera power cable provides a 2-pin

connector; an adapter with screw-down terminals is included in the box. 2) If powering the camera

with 12 Vdc, observe the polarity marked on the power drop cable.

12 Vdc polarity guide

Video drop cable

Terminal adapter

Power drop cable

Drop cable connectors

10. Verify that you can see video from your camera at the monitoring equipment.

BLK-CPD227VH 650 Line Outdoor

Vandalproof IR Camera

Quick Installation Guide

This document guides you through the basic steps to install and use your BLK-CPD227VH camera. The

camera includes 2.8-12 mm lens, 12 Vdc or 24 Vac powering.

Camera features include:

• Can be installed indoors or outdoor.

• 650 TV-line resolution in color, 720 TVL B / W

• Advanced Gen V DSP

• IP67 rated (waterproof)

• Durable enclosure: body is aluminum, dome is polycarbonate

• Smart DNR technology eciently reduces noise in low light conditions

• 75 foot range with Smart IR 24-LED IR LED array

• 3-axis camera gimbal - mountable on ceiling, wall or sloped surface

• Day & Night function (ICR)

• Support up to 8 privacy zones

• Digital Wide Dynamic Range (DWDR)

• Multi function : High-Light Mask, Lens Shading Compensation, Smart Motion Detection

• Smart IR technology greatly improves camera image in B / W mode when the IR LED array is on

• Multi-language full OSD support

Precautions

• Do not install the camera in locations subject to moisture or vibration.

• Do not scratch the camera, especially lens or dome cover.

• Operate the camera within the specied temperature range 14 °F ~ 122 °F (-10 °C ~ 50 °C).

• Handle with care. Dropping it can cause serious damage to the camera.

• Do not install the camera in locations where direct sunlight shines onto or be reected onto the lens.

• Use a 12 Vdc, 1A regulated power adapter, or 24 Vac power adaptor.

Installation

1. Remove the camera dome by loosening the three dome cover screws with the L-wrench provided,

then lifting o the cover. See the graphic to the right.

2. Remove the camera module assembly from the base by removing the two camera module screws.

3. Using the base as a template, mark the locations on the mounting surface for the mounting screws

(2) and the hole for the network video and power cables routed into the base. Note that the network

cable can be routed or through the mounting surface at the center of the base, or in through a cap

on the side of the base. The camera can be mounted on a ceiling or wall.

NOTE: An external video connector is provided on the camera module. See “Maintenance board”

on page 2.

11. While observing the video image from your camera, adjust the pan, tilt, and roll as follows to point

the camera at your surveillance target: Be careful not to displace the rubber ring around the lens.

a. Pan adjustment: Grasp the gimbal assembly, then rotate it (0° ~ 360°) left (L) or right (R).

b. Tilt adjustment: Grasp the protractor, then tilt it up (U) or down (D) (19° ~ 90°).

c. Roll adjustment: Grasp the camera module (within the gimbal), then rotate it (0° ~ 360°)

to set the horizon line of the image.

Gimbal

(Pan adjust)

Camera module

(roll adjust)

grasp here

Rubber ring (seal)

Protractor

(Tilt adjust)

12. While observing the video image from your camera, adjust the zoom and focus settings as follow

(see graphic below):

a. Zoom: Rotate the Tele (T) - Wide (W) ring (1) to produce the best view of your surveillance

target.

b. Focus: Rotate the Near (N) - Far (F) ring (2) to produce the best image clarity.

13. Reinstall the dome.

Maintenance board

The maintenance board is part of the camera module assembly. It includes an external video port, a debug

port, and a joystick for using the OSD menus.

Joystick

External video connector

Debug port

Video adapter cable

Maintenance board and video adapter cable

• External video connector: Use this connector with the adapter cable provided (2-pin to RCA) to

connect to a local monitor for observing video from the camera. This feature is useful during camera

setup and troubleshooting.

• Debug port: Maintenance port for engineering use only.

• Joystick: Used for accessing and conguring the camera through the on-screen display (OSD) menus:

The OSD menu structure is shown in the table below.

—Push the joystick down (toward the board) to open the OSD menu system, conrm a selection, or

open a submenu.

—Rock the joystick toward the UP or DOWN to move vertically through the OSD menus.

—Rock the joystick toward the LEFT or RIGHT to change the option displayed for an OSD parameter.

To select the parameter, press the joystick down.

—Example: Using the joystick to setup the camera for high ACG (automatic gain control).

»While observing video from the camera, press the joystick down to open the OSD main menu.

»Rock the joystick toward the UP or DOWN repeatedly until AGC is highlighted.

»Rock the joystick toward the LEFT or RIGHT repeatedly until HIGH appears.

»Press the joystick down to conrm the selection.

»Rock the joystick toward the UP or DOWN repeatedly to highlight RETURN.

»Press the joystick down to conrm the selection (RETURN: close the menu).

OSD Menu Structure

Function

setting menu Select menu Sub-menu Contents

1. EXPOSURE

Lens DC

Brightness 0 ~ 99 : Adjust brightness with a DC iris lens

E. Shutter AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500, 1/1000, 1/2000,

1/4000, 1/10000, 1/100000 : Adjust shutter speed

AGC OFF, LOW, MIDDLE, HIGH Sets the AGC level. Note: You can not use Auto D&N change mode

when AGC is o.

SENSE-UP AUTO, OFF, X2, X4, X8, X16, X32, X64,

X128, X256, X512, X1024 Use sense-up in low luminance (x2 ~ x1024)

BACKLIGHT

BLC

BLC LEVEL OFF, LOW, MID, HIGH : BLC function, level selectable

TOP 0 ~ 15: Adjust top position of BLC zone

BOTTOM 1 ~ 16 : Adjust bottom position of BLC zone

LEFT 0 ~ 15: Adjust left position of BLC zone

RIGHT 1 ~ 16 : Adjust right position of BLC zone

HLC

HBLC

OFF : Deactivates HBLC function

MANUAL

HBLC LEVEL : OFF, LOW, MID, HIGH

Make a zone for HBLC:

TOP : 0 ~ 15

BOTTOM : 1 ~ 16

LEFT : 0 ~ 15

RIGHT : 1 ~ 16

MODE ALL DAY : Activates HBLC function all day

NIGHT : Use the function at night only

HLC LEVEL 1 ~ 100 : Level adjust

MASK 1 ~ 4

Make a zone for HLC mask:

TOP : 0 ~ 33

BOTTOM : 1 ~ 34

LEFT : 0 ~ 44

RIGHT : 1 ~ 45

OFF : HLC MASK OFF

D-WDR SET LEVEL 0 ~ 20 : DWDR level adjust

Function

setting menu Select menu Sub-menu Contents

3D-DNR OFF, LOW, MID, HIGH, AUTO Reduces noise in low illumination (level selectable)

RETURN Move back to previous menu

2. WHITE BALANCE

AWB MODE

ATW Color temperature 2500 ~ 9500 K

MANUAL

M-WR 0 ~ 128 : Adjust the Red value to shift the color of the object

M-WB 0 ~ 128 : Adjust the Blue value to shift the color of the object

RETURN Move back to previous menu

PUSH Find the optimal white balance for current luminance environment

R-Y GAIN 0 ~ 255 Adjust Red tone of the image

B-Y GAIN 0 ~ 255 Adjust Blue tone of the image

RETURN Move back to previous menu

3. DAY & NIGHT

D&N MODE

AUTO

DAY g NIGHT 7 ~ 30 Select brightness of illumination about changing the

day D night mode by AGC

NIGHT g DAY 6 ~ 29

DELAY TIME 0 ~ 15 : Select the duration time

RETURN Move back to previous menu

AUTO-CDS

A. DAY g NIGHT 6 ~ 36 Select brightness of illumination for

changing the day D night mode by AGC

A. NIGHT g DAY 6 ~ 36

C. DAY g NIGHT 0 ~ 255 Select brightness of illumination for changing the day

D night mode by CDS

C. NIGHT g DAY 0 ~ 255

DELAY TIME 0 ~ 15 : Select the duration time

RETURN Move back to previous menu

COLOR Fixed at color

B&W Fixed at B/W

EXT DELAY TIME 0 ~ 15 : Change the color D B/W by external signal (N/A)

RETURN Move back to previous menu

BURST ON, OFF Transmit the burst signal or not in B/W mode

C_SUP 0 ~ 100 Color suppress controllable

A_SUP 0 ~ 100 Iris suppress controllable

SMART IR ON, OFF Decreases screen saturation of objects within a short range

RETURN Move back to previous menu

4. IMAGE ADJUST

MIRROR MIRROR, OFF Set a vertical image inversion

SHARPNESS 0 ~ 30 Sharpness adjustable

GAMMA

0.45, 0.55, 0.65 Set gamma value

USER GAMMA 0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55, 0.60, 0.65, 0.70, 0.75,

0.80, 0.85, 0.90, 0.95, 1.00 : Gamma adjustable

RETURN Move back to previous menu

LSC ON SET LEVEL 0 ~ 30 : Use the LSC and level adjustable

RETURN Move back to previous menu

OFF LSC OFF

RETURN Move back to previous menu

5. MOTION

MOTION ON, OFF Motion detection function activate/deactivate

AREA AREA 1 ~ 4

TOP: 0 ~ 143

Make a zone for motion detection

BOTTOM 2 ~ 145

LEFT 0 ~ 190

RIGHT 2 ~ 192

RETURN Move back to previous menu

SENSITIVITY 1 ~ 30 Motion detection sensitivity

DISPLAY OFF, MESSAGE, TRACE Select notication method of motion detection

HOLD TIME 0 ~ 15 Set the duration of alarm out

ALARM OUTPUT ON, OFF Alarm ON/OFF

RETURN Move back to previous menu

6. PRIVACY

MASK 1 ~ 8

OFF Display each privacy mask or not

DOT SEL L_TOP, L_BOT, R_BOT, R_TOP : Determines which of the 4 vertices

of each MD area is to be used

DOT XY ENTER SETTING : Determines the coordinate

MOVE XY ENTER SETTING : Move the mask

COLOR BLACK, WHITE, … : Select mask color (8 colors)

RETURN Move back to previous menu

Function

setting menu Select menu Sub-menu Contents

RETURN Move back to previous menu

7. SPECIAL

LANGUAGE ENGLISH, … : Select language (9 languages)

TITLE OFF, ON

EDIT Display the camera name on the screen

RESET Camera name reset

POSITION Camera name position

RETURN Move back to previous menu

COMMUNICATION OFF Not used.

DPC

OFF Deactivates Defect Pixel Correction in low illumination

AUTO

WHITE THR 0 ~ 255 : Setup the limited value of white pixel correction

LUMA THR 0 ~ 255 : Setup the limited value of white pixel correction

RETURN Move back to previous menu

FACTORY SET YES, NO Reset your camera to factory default condition

RETURN Return to previous menu

8. EXIT

SAVE AND EXIT Save values and exit menu

EXIT Exit the menu without save

RETURN Move back to previous menu

Dimensions

3.37”

4.07”

3.29”

2.16”

4.65”

Specications

Image Sensor 1/3” SONY SUPER HAD CCD II

Eective Pixel 768 (h) x 494 (v) pixels (NTSC))

Cell Size 6.35 μm (h) x 7.4 μm (v) (NTSC))

Scanning System 2:1 interlace

Sync. Type Internal

Resolution Color : 650 TV-Line, B / W : 720 TV-Line

S / N ≥ 52 dB (AGC o)

Video Output 1.0 Vp-p (sync. negative) termination 75 Ω

Minimum Illumination 0.01 lux (f/1.2), 0.0001 lux (sense up), 0 lux (75 ft range with 24 piece LED array) - indoor

Gamma ȳ = 0.45 typical (0.2 ~ 1.0)

OSD Yes (multi language)

White Balance ATW (2500 K ~ 9500 K) / manual / AWC

Shutter Speed 1/60 (NTSC) ~ 1/100,000 s

Sense up Auto (selectable limit 2x ~ 1024x) / FIXED / OFF

Backlight OFF / BLC / HLC / DWDR

AGC LOW / MIDDLE / HIGH / OFF

DNR (3D) AUTO / LOW / MIDDLE / HIGH / OFF

Motion Detection ON / OFF (4 zones)

Privacy Zone ON / OFF (8 zones)

Mirror ON / OFF

Day & Night ICR (AUTO, COLOR, B / W)

LED Brightness 24 piece array, Smart IR

Blemish Compensation AUTO / OFF

Lens Vari-focal auto iris lens

Power Supply 12 Vdc / 24 Vac dual voltage

Current Consumption Max. 500 mA (at 12 Vdc, 24 Vac): LEDs on

Operation Temperature 14 °F ~ 122 °F (-10 °C ~ 50 °C)

Storage Temperature. -4 °F ~ 140 °F (-20 °C ~ 60 °C)

Dimension Ø4.65” x 4.07” (h)

Weight 20.11 oz (570 g) approx.

Indice

Altri manuali Observint Telecamera IP

Observint

Observint NB8 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente