Oce TDS750 Manuale utente
-
o
Océ
TDS750
Rising Above
User manual
Safety information
Copyright
© 2012, Océ
All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted
in any form or by any means without written permission from Océ.
Océ makes no representation or warranties with respect to the contents hereof and specifi-
cally disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Océ reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation to notify any person of such revision
or changes.
Edition: 2012-05
Contents
Chapter 1
Instructions for safe use.....................................................................................5
Instructions for safe use............................................................................6
Chapter 2
Regulation notices............................................................................................11
Regulation notices....................................................................................12
Chapter 3
General information.........................................................................................17
Caution labels and notations...................................................................18
Chapter 4
Miscellaneous....................................................................................................19
Online support for your product.............................................................20
3
Contents
4
Contents
Chapter 1
Instructions for safe use
Instructions for safe use
Introduction
All the products have been tested in accordance with the strictest international safety
standards. Please read the following sections before you connect the machine to the
power supply. These sections contain important information with regard to the user
safety and the prevention of equipment problems. Make sure that you observe the safety
rules hereinafter. This helps to assure that you can work with the product safely. Make
sure that you observe all the precautions mentioned below.
Note:
Some parts of the contents of this section may not be applicable to your product.
Note:
Please refer to the corresponding Safety Data Sheets for specific safety information. You
can download the Safety Data Sheets from the support site of your product at
http://global.oce.com/support/.
.
Warning and precaution symbols
Warning:
Ignoring this warning could cause serious injury or even death.
Caution:
Ignoring this warning could cause injury or damage to property.
Note:
Indicates additional important information.
The indicators above are used on the warning labels or in the manuals to categorize the
level of safety warnings.
.
Chapter 1 - Instructions for safe use6
Instructions for safe use
Disassemble and modification
Warning
•Do not remove covers and panels which are fixed to the machine. Some machines
have a high-voltage component or a laser beam source inside that could cause an
electrical shock or blindness
•Do not modify this machine, because this could cause a fire, electrical shock or
breakdown. If the machine contains a laser, the laser beam source could cause blindness.
•The fuser must be closed during normal operation. The fuser may only be opened to
remove paper after a paper jam. Because of hot surfaces, the operator must always be
cautious and wear heat-protective gloves when removing printing material in the fuser
section.
•Turn off the machine before opening the fuser.
Caution
•Do not carry out maintenance activities for other components and maintenance ma-
terials than the components and materials that are mentioned in the user manual.
•Do not place any liquids on the machine.
•Do not open any door while the machine starts up or runs, unless the operator panel
displays a message that asks you to open one or more doors.
•Use maintenance materials or other materials for their intended purpose only.
•To avoid any risk, only properly qualified and trained service technicians are allowed
to modify the machine.
•Do not bridge any mechanical or electrical circuit breakers.
•Exercise caution when placing rolls in the printer. If the Océ TDS750 printer is not
equipped with the optional roll loader, the NIOSH limit value for handling loads will
be exceeded if rolls of imaging materials having a net weight of more than 7 kg/15.4
lbs (i.e. a width of more than approx. 50 cm or 20 inches) are placed in roll positions
nos. 2, 4 and 6 by only one person.
•Only one drawer can be opened at a time. This is to prevent overbalance of the
printer.
•Keep maintenance materials away from children.
Note
•The left cover must be closed during normal operation. This is necessary to ensure
proper operation.
Power cord
Warning
•Do not use any power cable other than the one provided. Never use the power cable
with any other electrical device.
•Do not scratch, abrade, heat, twist, bend, place a heavy object on or cause any other
damage to the power cord. The use of a damaged power cord (exposed core wire,
broken wire, for example) could result in a fire or breakdown. If you find any of these
Chapter 1 - Instructions for safe use 7
Instructions for safe use
conditions, immediately turn OFF the power switch and unplug the power cord from
the power outlet. Then call your authorized service representative.
•Do not use an extension lead to connect the machine.
•Only use the mains connector cable that was supplied with the machine.
Power source
Warning
•Put the power plug directly into a wall socket that has the same configuration as the
plug. The use of an adapter leads can result in an inadequate power supply. If a
proper wall outlet is not available, ask a qualified electrician to carry out the installation.
•Do not connect the machine to a mains voltage that differs from the value as stated
on the power marking label.
•Do not use a multiple outlet adapter or an extension lead. Contact your authorized
service representative if an extension lead is required.
Caution
•Consult your authorized service representative before you connect other equipment
to the same wall outlet.
Note
•If connection to a different mains voltage is required, contact your authorized service
representative.
Power plug
Warning
•For machines that are connected via a wall socket: Place the machine close to a wall
socket that is easily accessible. The power plug is intended to serve as a disconnect
device.
Grounding
Warning
•Connect the power cord to an electrical outlet (wall socket) that is equipped with a
grounding terminal.
•This equipment has not been designed for connection to an IT power system. An IT
power system is a voltage network in which the neutral wire is not connected to ground.
Installation
Warning
•Make sure that the machine is placed on a level, horizontal surface of sufficient strength.
•Make sure that the machine stands on its feet so all four wheels turn freely.
•Do not place this machine on an unstable or tilted bench.
•Do not place this machine in a location that is subject to lots of vibrations and shocks.
Chapter 1 - Instructions for safe use8
Instructions for safe use
•Do not use flammable sprays, liquids or gases near this product, because this could
cause a fire.
Note
•We recommend that you only connect copy-control products (or other products) that
meet (inter)national product safety and radio frequency interference standards. Only
use an attachment cable as specified by the manufacturer.
Ventilation
Caution
•The machine can produce odors of exhaust air when you:
– use this machine in a poorly ventilated room for a long time
– produce large amounts of copies or prints
Therefore, make sure that you ventilate this room well.
•Do not block the ventilation openings of the machine.
•Do not place the machine in rooms which are too small and insufficiently ventilated.
See the Product Safety Data Sheet of the machine for the ventilation requirements.
Actions in response to troubles
Warning
•When a piece of metal, water or any other similar foreign matter gets inside the ma-
chine, immediately turn OFF the power switch and unplug the power cord from the
power outlet. Then call your authorized service representative.
•Immediately stop using the machine if the machine becomes excessively hot, emits
smoke, or produces unusual odors or noises. Immediately turn OFF the power switch
and unplug the power cord from the power outlet. Then call your authorized service
representative.
Caution
•Stop using the machine if the machine was dropped or a cover was damaged. Imme-
diately turn OFF the power switch and unplug the power cord from the power outlet.
Then call your authorized service representative.
•Some areas inside the machine become hot. Touching these areas could cause burns.
When you check for malfunctions inside the machine, such as a paper misfeed, do
not touch the spots labeled "Caution HOT". You can find these labels around the
fusing unit, for example.
•LCD display. Do not rub, press or touch the display surface with hard material, because
the polarizer at the surface can be easily scratched. The LCD module consists of glass.
Therefore, the LCD module can damage when you drop, pinch strongly or punch
the module. When glass breaks, be careful that you do not get injured by glass pieces.
Call Customer Service.
Chapter 1 - Instructions for safe use 9
Instructions for safe use
Consumables, supplies and maintenance materials
Warning
•Do not throw contaminated parts or parts containing toner or ink into an open flame.
•Do not leave contaminated parts or parts containing toner or ink within reach of
children.
Caution
•Always use the materials which the manufacturer recommended and which are devel-
oped for this machine. Materials not approved by the manufacturer may result in
faults in your machine.
Moving the machine
Caution
•Make sure that you disconnect the power cord and other cables before you move the
machine.
•Make sure that you check the documentation for the space requirements before you
move the machine.
Holidays
Caution
•Unplug the machine when you will not use the machine for a long period of time.
Chapter 1 - Instructions for safe use10
Instructions for safe use
Altri manuali per TDS750
1
Indice
Altri manuali Oce Stampante
Oce
Oce Arizona 550 GT Manuale utente
Oce
Oce TCS400 Istruzioni per l'installazione
Oce
Oce ColorWave 600 Manuale utente
Oce
Oce Imagistics ix 2701 Manuale utente
Oce
Oce 1010N - B/W Laser Printer Manuale utente
Oce
Oce OP14 Manuale utente
Oce
Oce CS9360 Manuale utente
Oce
Oce Colorado 1640 Manuale utente
Oce
Oce PP20D Manuale utente
Oce
Oce ColorWave 900 Manuale utente
Oce
Oce PlotWave 340 Manuale utente
Oce
Oce 9800 Manuale utente
Oce
Oce arizona 1240 GT Manuale utente
Oce
Oce TCS500 Manuale utente
Oce
Oce Oce TDS800 Manuale utente
Oce
Oce ColorWave 300 Manuale utente
Oce
Oce Arizona T220UV Manuale utente
Oce
Oce TDS750 Manuale utente
Oce
Oce CS6410 Istruzioni per il montaggio
Oce
Oce PlotWave 350 Manuale utente
