Oki C712 Guida utente
Version 1.0
1
Thank you for choosing OKI.
This is C712 configuration instructions for Ballot model. These instructions explain 2 ways for
configuration. Manually and using Ballot Configuration Tool.
Before ballot configuration, please perform the following steps.
1. Install Extended 2nd Paper Tray for 19" Ballots (Order/Part Number 44274505).
2. Turn ON the device.
3. Print the Configuration pages. (Print Information -> Configuration -> Execute)
4. Check Serial Number and the current tray 2 setting from the configuration pages.
[Serial Number]
[Tray 2 Setting (Paper Size)] (Before Ballot Configuration)
Notes: Be sure to note down the serial number as it is necessary for inquiry.
If you do not have Ballot Configuration Tool you can set by using device menu, please
proceed to next page. In case you have Ballot Configuration Tool, please proceed to page 3.
Version 1.0
2
1. Installation Steps: Using Device panel menu (Manually)
Menus -> Tray Configuration -> Tray 2 Config
-> ->
1. Set Paper Size from “Cassette Size”
to “Custom”.
2. Return to “Tray 2 Config” Menu.
3. Set X Dimension to “8.5 inch”.
4. Set Y Dimension to “19.0 inch”.
5. Complete
Version 1.0
3
2. Installation Steps: Using Ballot Configuration Tool
①Connect the PC and the device with a USB cable.
②Copy the module of the Data Transmitter which provided by OKI to your desktop.
1. Run the Data Transmitter Tool “DT.exe”.
2. Select your language and click “OK”.
3. Select “Open” from the file menu.
4. Select “setup.dtd” file.
(To be Continued)
Version 1.0
4
5. Select “C712-b Configuration” function.
6. Search a USB connected printer. If the
device was found, select it, and click
“Send”.
7. Click “OK”.
Please wait for about 10 seconds.
After the applying configuration, the
device will restart (Turn OFF and ON)
automatically.
8. The configuration is completed. The
device will auto reboot (Turn OFF and
ON).
(To be Continued)
Version 1.0
5
9. After reboot, the device does initialize.
After initializing, the device status
changes to ready.
10. Click “OK” and close this tool.
11. Print the Configuration pages.
MENU -> Print Information ->
Configuration -> Execute
12. Check the current tray 2 setting from
the configuration pages.
Paper Size is “Custom”.
X Dimension is “8.5 inch”.
Y Dimension is “19.0 inch”.
13. Complete
Version 1.0
6
3. Confirmation of setup
You can check the setup result from the 1st page of Configuration pages.
How to print the Configuration pages. (Print Information -> Configuration -> Execute)
Where and what should you look up?
Setup was successful if the following were applied to the Tray 2 settings:
•Paper Size is “Custom”.
•X Dimension is “8.5 inch”.
•Y Dimension is “19.0 inch”.
If the above settings are not applied, please repeat above procedure.
End of File
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Oki Stampante
Oki
Oki PACEMARK 4410 Manuale utente
Oki
Oki MPS711c Manuale di servizio
Oki
Oki GL408e Manuale utente
Oki
Oki C9000 Series Manuale utente
Oki
Oki proColor pro900DP Manuale utente
Oki
Oki ES2024 Manuale utente
Oki
Oki Teriostar LP-1040-MF Manuale utente
Oki
Oki LP-2050-MF Manuale utente
Oki
Oki OKIPAGE14e Manuale utente
Oki
Oki C9200 Manuale utente
Oki
Oki B6500 Series Guida utente
Oki
Oki B412dn Manuale utente
Oki
Oki C5300 Manuale utente
Oki
Oki ML620 Manuale utente
Oki
Oki MPS711c Istruzioni originali
Oki
Oki C5400 Series Manuale utente
Oki
Oki C8800dn Manuale utente
Oki
Oki MICROLINE Turbo ML390 Manuale utente
Oki
Oki B6300 Series Manuale utente
Oki
Oki OKIPAGE 10e Manuale utente
