Oki OKIPAGE 8z Scheda tecnica
Quick
Setup
3
2
1Check Contents
Remove the Protective Sheet
Tilt up the image drum and lift it out. Do not
touch image drum’s green surface.
Install the Paper Feed Tray
Before you can use your printer:
q
Steps 1 to 5 - Setup your printer.
q
Step 6 - Install the correct Interface cable for your system—USB or Parallel.
q
Step 7 - Determine your computer’s Operating System—Windows®95, 98, 2000, NT®4.0 or
Macintosh®(OS 8.1 or higher), then install the correct printer software for your computer’s
Operating System and Interface.
q
See the on-line User’s Guide for more information about your printer.
Press down firmly until drum snaps into place.
Ê
Printer
Ë
Paper Feed Tray
Ì
Toner
Í
Power Cord
Î
CD
Ï
Light-Shield Bag (to protect image
drum from light when it is removed
from printer)
➐Quick Setup Instructions
!Interface cable is not included. For
information on cable requirements, see
“Supplies” in the on-line User’s Guide.
Pull out sheet ➊, and remove tape ➋.
If transparent film is attached, remove
film with sheet.
58341901
Lift the cover.
Replace the image drum, tilting it down
to slide under the guides ➊.
➊
➊
➊
➋
Press to lock tray in place.
Align tabs on bottom of paper tray
into slots on back of printer.
Swing tray up and align tabs
and slots at top.
©2000 Oki Data Americas, Inc.
➊
➋
➌
➍
➎
➏
➐
All manuals and user guides at all-guides.com
all-guides.com
6
4
5
Push lock lever down towards rear.
Insert Paper
Adjust left guide for paper size. Insert a stack of paper. (max. 100 sheets, 20 lb.) Adjust the right guide gently against the paper. Make sure power is off.
Install Toner
Connect to Your Computer
Connecting to a USB Port
For Windows 98/2000 and Macintosh Computers with a USB
port. Requires USB cable.
1Connect the USB cable to the computer’s USB port.
2Connect the other end of the USB cable to the printer’s USB
port.
3Go to Step 7, Install the Printer Software.
Connecting to a Parallel Port
Requires IEEE 1284-compliant bi-directional parallel cable.
1Make sure the computer and printer are turned off.
2Connect the parallel cable to the computer’s parallel port.
Secure the screws.
3Connect the other end of the cable to the printer’s parallel
port. Secure it with the wire clips.
4Go to Step 7, Install the Printer Software.
Plug the power cord into the printer and into a
grounded electrical outlet.
With label up, place left side
under tab ➊, lower into the
toner well. Close the cover.
Unwrap toner cartridge. Shake
side to side to distribute toner.
Lift out toner well cover and discard.
➊
Pulling firmly, remove
tape from bottom.
All manuals and user guides at all-guides.com
Altri manuali per OKIPAGE 8z
4
Altri manuali Oki Stampante
Oki
Oki C3450m Manuale utente
Oki
Oki C9600hdn Manuale utente
Oki
Oki OkiPos 441 Istruzioni per il montaggio
Oki
Oki B410D Manuale di servizio
Oki
Oki LD670 Manuale utente
Oki
Oki ML620 Guida rapida
Oki
Oki OKIMATE 10 Manuale utente
Oki
Oki C5650 Manuale di servizio
Oki
Oki ML1120 Plus Manuale utente
Oki
Oki C7200 Manuale utente
Oki
Oki ML1120 Manuale utente
Oki
Oki C831TS Manuale del proprietario
Oki
Oki lp-1030-mf Manuale utente
Oki
Oki C9800hdn Manuale utente
Oki
Oki microline ML393 Manuale utente
Oki
Oki ML3321 Manuale utente
Oki
Oki C 5650n Manuale utente
Oki
Oki LP470s Manuale utente
Oki
Oki C911 DICOM Manuale utente
Oki
Oki OKIPAGE 4W PLUS Guida di riferimento
