Oki okipos Manuale utente
OKIPOS 407
USER’S GUIDE
GUIDE DE L'UTILISATEUR
MANUALE D'USO
BENUTZERHANDBUCH
GUÍA DEL USUARIO
MANUAL DO UTILIZADOR
OKIPOS
Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. manufacturer
assumes no responsibility for the results of errors beyond its control. manufacturer also cannot guarantee that changes in software
and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it.
Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer.
Copyright © 2005. All rights reserved.
Energy Star is a trademark of the United States Environmental Protection Agency
product complies with the requirements of the Council Directives 89/336/EEC (EMC) and
73/23/EEC (L VD), as amended where applicable, on the approxi-
mation of the laws of the member states relating to Electromagnetic Compatibility and Low Volt-
age.
Energy Star
As an Energy Star Program Participant, the manufacturer has determined that this product
meets the Energy Star guide-lines for energy efficiency.
CONTENTS
Parts Identification and Nomenclature .............................................................1
Consumable Parts and AC Adapter ..................................................................3
Connecting Cables and AC Adapter..................................................................5
Interface Cable ...............................................................................................5
Connecting to a Peripheral Unit.....................................................................7
Connecting the Optional AC Adapter............................................................8
Turning Power On .........................................................................................9
Control Panel and Other Functions.................................................................10
Control Panel ...............................................................................................10
Errors ...........................................................................................................10
Self Printing .................................................................................................12
Loading the Roll Paper .....................................................................................13
Adjusting the Near-end Sensor ........................................................................16
Preventing and Clearing Paper Jams ..............................................................18
Preventing Paper Jams .................................................................................18
Removing Paper Jam ...................................................................................18
Periodical Cleaning ...........................................................................................19
Cleaning the Thermal Head .........................................................................19
Cleaning the Paper Holder ...........................................................................19
Appendix A: Specifications..............................................................................123
A-1. General Specifications ........................................................................123
A-2. Auto Cutter Specifications ..................................................................124
A-3. Interface ..............................................................................................124
A-4. Electrical Characteristics ....................................................................124
A-5. Option .................................................................................................124
A-6. Environmental Requirements..............................................................125
A-7. Reliability............................................................................................125
A-8. Black mark specifications ...................................................................126
Appendix B: Dip Switch Setting......................................................................127
B-1. Parallel Interface Type ........................................................................128
B-2. Serial Interface Type...........................................................................130
B-3. USB Interface Type ............................................................................133
B-4. Ethernet Interface Type.......................................................................134
Appendix C: Parallel Interface .......................................................................135
Appendix D: Serial Interface...........................................................................136
D-1. RS-232C Connector ............................................................................136
D-2. Cable Connections ..............................................................................138
D-3. Electrical Characteristics ....................................................................138
Appendix E: Periheral Unit Drive Circuit .....................................................139
Appendix F: Memory Switch Settings ............................................................140
ENGLISH
– 1 –
ENGLISH
Parts Identification and Nomenclature
Roll paper User’s manual
Cover open lever
Pull this lever in the
direction of the
arrow to open the
printer cover.
Control panel
Features LED indica-
tors to indicate printer
status and switches to
operate the printer.
Ferrite core Fastener
(Parallel interface
model only) (Parallel interface
model only)
Printer cover
Open this cover to load or
replace paper.
Power connector
For connection of
the AC adapter.
Never unplug the
AC adapter while
the printer is on.
Peripheral drive connector
Connects to peripheral
units such as cash
drawers, etc.
Do not connect this to a
telephone.
Interface connector
For connection to a
host computer.
Power switch
Used to turn on/off
power to the printer.
–2 –
ENGLISH
Choosing a place for the printer
Before actually unpacking the printer, you should take a few minutes to
think about where you plan to use it. Remember the following points
when doing this.
✓Choose a firm, level surface where the printer will not be exposed to
vibration.
✓The power outlet you plan to connect to for power should be nearby
and unobstructed.
✓Make sure that the printer is close enough to your host computer for
you to connect the two.
✓Make sure that the printer is not exposed to direct sunlight.
✓Makesurethattheprinteriswellawayfromheatersandothersources
of extreme heat.
✓Make sure that the surrounding area is clean, dry, and free of dust.
✓Make sure that the printer is connected to a reliable power outlet. It
should not be on the same electric circuit as copiers, refrigerators, or
other appliances that cause power spikes.
✓Make sure that the room where you are using the printer is not too
humid.
–3 –
ENGLISH
Consumable Parts and AC Adapter
When consumable parts have run out, use those specified in the table below.
Make sure that the AC adapter specified in the table is used.
Use of consumable parts or AC adapter which are not specified in the table may
result in damage to the printer, fire or electric shock.
(1) Roll paper specification
Thermal paper
Thickness: 65~150
∝
m
Width: 79.5±0.5 mm or 82.5±0.5 mm or 57.5±0.5 mm
Outer roll diameter: ø100 mm or less
Take up paper roll width: 80 mm or 83 mm or 58 mm
Core outer/inner diameter
Paper thickness Core outer Core inner
65~75
∝
mø18±1 mm ø12±1 mm
65~75
∝
mø32±1 mm ø25.4 mm
75~150
∝
mø32±1 mm ø25.4 mm
Printed surface: Outer edge of roll
Tail end handling: Do not use paste or glue to secure the roll paper or
its core.
Do not fold the tail end of the paper.
(2) Recommended paper
Mitsubishi Paper Mills Limited
P220AG (normal type paper), 65
∝
m (thickness)
HP220A (high image stability paper), 65
∝
m (thickness)
HP220AB-1 (high image stability paper), 75
∝
m (thickness)
P220AB (normal type paper, card ticket), 85
∝
m (thickness)
P220AC-1 (normal type paper, card ticket), 95
∝
m (thickness)
P220AC (normal type paper, card ticket), 105
∝
m (thickness)
P220AD (normal type paper, card ticket), 130
∝
m (thickness)
P220AE-1 (normal type paper, card ticket), 150
∝
m (thickness)
PB670 (2 color paper: Red & Black), 75
∝
m (thickness)
PB770 (2 color paper: Blue & Black), 75
∝
m (thickness)
Oji Paper Co., Ltd.
PD150R (normal type paper), 75
∝
m (thickness)
PD160R (high image stability paper), 65/75
∝
m (thickness)
PD750R (2 color paper: Red & Black), 75
∝
m (thickness)
PD700R (2 color paper: Blue & Black), 75
∝
m (thickness)
Nippon Paper Industries
TF50KS-E2C (normal type paper), 65
∝
m (thickness)
+0.5
-1 +0.5
-1 +0.5
-1
–4 –
ENGLISH
Kanzaki Specialty Papers Inc. (KSP)
P320RB (2 color paper: Red & Black), 65
∝
m (thickness)
P320BB (2 color paper: Blue & Black), 65
∝
m (thickness)
Depending on the type and thickness of the paper, it may be necessary to change
the settings for printing darkness. To change the darkness settings, use the
printing darkness settings command <ESC><RS> ‘d’n. Refer to the separate
programmer’s manual for details.
(3) AC adapter (option)
Model name: PS60A
Input: 100 to 240 V AC, 50/60 Hz
Output: DC24±5%, 2.0 A (5.0 A Load 10 sec. Max)
–5 –
ENGLISH
Connecting Cables and AC Adapter
Interface Cable
Ferrite Core Installation (Parallel interface model only)
(1)Foronlytheparallelinterfacemodel,
affix the ferrite core onto the cable
as shown in the illustration below.
(2)Pass the fastener through the ferrite
core.
(3)Loop the fastener around the cable
and lock it. Use scissors to cut off
any excess.
Ferrite core
Interface cable
5 cm
maximum
Fastener
Pull and cut
–6 –
ENGLISH
Connecting the Interface Cable
Note: Before connecting/disconnecting the interface cable, make sure that
power to the printer and all the devices connected to the printer is
turned off. Also make sure the power cable plug is disconnected from
the AC outlet.
(1)Connect the interface cable to the connector on the rear panel of the printer.
(2)In the case of a serial interface, tighten the connector screws. In the case of a
parallel interface, fasten the connector clasps.
Serial interface cable
Parallel interface cable
–7 –
ENGLISH
Connecting to a Peripheral Unit
You can connect a peripheral unit to the printer using a modular plug. The
followingdescribeshowtoinstalltheferritecoreandmaketheactualconnection.
See “Modular plug”on page 96 for details about the type of modular plug that is
required. Note that this printer does not come with a modular plug or wire, so it
is up to you to obtain one that suits your needs.
Important!
MakesurethattheprinteristurnedoffandunpluggedfromtheACoutlet
and that the computer is turned off before making connections.
(1)Connect the peripheral drive cable to the connector on the rear panel of the
printer.
Important!
Do not connect a telephone line into the peripheral drive connector.
Failure to observe this may result in damage to the printer.
Also, for safety purposes, do not connect wiring to the external drive
connector if there is a chance it may carry peripheral voltage.
(2) Connect the ground wire. (Europe only)
Take out the screw shown in the figure below, then fasten the ground wire
terminal to the place where the screw was removed and tighten the screw.
Europe only
Indice
Lingue:
Altri manuali Oki Stampante
Oki
Oki ES6410 Manuale utente
Oki
Oki OKIPAGE 10ex Manuale di programmazione
Oki
Oki C7350hdn Manuale del proprietario
Oki
Oki C 5650dn Manuale utente
Oki
Oki C911dn Manuale
Oki
Oki OL1200 Manuale utente
Oki
Oki Microline 8480 FB Manuale utente
Oki
Oki ML490 Series Manuale utente
Oki
Oki PRO330S Manuale utente
Oki
Oki proColor pro900DP Manuale utente
Oki
Oki LD610 T Istruzioni per l'installazione
Oki
Oki C711dn Manuale utente
Oki
Oki C610dn Istruzioni operative e di manutenzione
Oki
Oki C532 Manuale utente
Oki
Oki B6250dn Istruzioni per l'installazione
Oki
Oki C3600n Manuale utente
Oki
Oki B6200 Series Manuale utente
Oki
Oki C 5650n Scheda tecnica
Oki
Oki ML1190 Manuale utente
Oki
Oki 10i Manuale
