Oliver 4630 Manuale utente
4630 18” Bandsaw
Owner’s Manual
Oliver Machinery M-4630 9/2003
Seattle, WA Copyright 2003
SAFETY RULES
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN
SERIOUS PERSONAL INJURY.
1. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE
OPERATING THE TOOL. Learn the tool’s application and limitations as well
as the specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION. Wear safety glasses. Everyday
eyeglasses only have impact resistant lenses; they are not safety glasses.
Also use face or dust mask if cutting operation is dusty. These safety glasses
must conform to ANSI Z87.1 requirements.
Note: Approved glasses have Z87 printed or stamped on them.
4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning it
on.
5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in
damp or wet locations, or expose them to rain. Keep work area well lighted.
7. KEEP CHILDERN AWAY. All visitors should be kept safe distance from work
area.
8. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by
removing starter keys.
9. DON’T FORCE TOOL it will do the job better and safer at the rate for which it
was not designed.
10.USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it
was not designed.
1
11.USE PROPER EXTENSION CORD. Make sure your extension cord is in
good condition. When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. Table
1 shows the correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller the gage
number, the heavier the cord.
12.WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective hair covering to contain
long hair.
13.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant lenses,
they are NOT safety glasses.
14.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer
than using your hand and it frees both hands to operate tool.
15.DON’T OVERREACH. Keep proper footing and balance at all times.
16.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating and changing
accessories.
17.DISCONNECT TOOLS before servicing; when changing accessories, such
as blades, bits, cutters, and the like.
18.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is
in off position before plugging in.
19.USE RECONNENDED ACCESSORIES. Consult the owner’s manual for
recommended accessories. The use of improper accessories may cause risk
of injury or persons.
20.NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if
the cutting tool is unintentionally contacted.
21.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function-check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation.A guard or other part that is
damaged should be properly repaired or replaced.
22.DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
23.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a complete stop.
24.MAME SURE TOOL IS DISCONNECTED from power supply while motor is
being mounted, connected or reconnected.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY RULES FOR BAND SAWS
1. If you are not thoroughly familiar with the operation of band saws, obtain
advice from your supervisor, instructor or other qualified person.
2. Follow all wiring codes and recommended electrical connections. Make
certain that the tool is properly grounded.
3. Make all adjustments with the power “OFF”
4. Always maintain proper adjustment of blade tension, blade guides, and blade
support bearings.
5. Avoid awkward hand positions. A sudden slip could allow the hand to contact
the blade.
6. Do not attempt to saw stock that does not have a flat surface, unless a
suitable support is used.
7. Make sure blade is not contacting the workpiece before turning on the power
switch.
8. Always keep hands and fingers away from the blade when the machine is
running.
9. Hold workpiece firmly against table and feed into blade at a moderate speed.
10. Made sure that the saw blade teeth point downward toward the table.
11. Adjust upper guide to just clear work piece.
12. Disconnect machine from the power source when making repairs.
13. Replace all guards after servicing.
14. Turn off band saw if the material is to be backed out of an uncompleted cut.
15. Make relief cuts before cutting long curves.
16. Do not cut material that is too small to be safely supported.
17. Support long heavy work from the floor.
18. Before leaving the machine, make sure the work area is clean.
19. Important: When the tool is not in use , the switch should be in the “OFF”
position and the power cord disconnected.
20. Do not remove jammed cutoff pieces until blade has stopped.
ON-OFF SWITCH PADLOCK – To safeguard the band saw from unauthorized
operation and to avoid accidental starting by children or other not qualified to use,
the use of padlock is required. To lock out the on – off switch, open the padlock,
insert through the hole of the switch on button and close the padlock. Place the
key in a location that is inaccessible to children and other not qualified to use the
tool.
SWITCH WITH KEY – The switch key must be inserted into the switch before
saw can operate. To lock the switch in the OFF position, remove the switch key
from the switch. Place the key in a location that is inaccessible to children and
others not qualified to use the tool.
GROUNDING INSTRUCTIONS
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock. This
tool is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug.
The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided – if it will not fit the outlet, have the proper
outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result In a
risk of electric shock. The conductor with insulation having an outer surface
that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary, do
not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding
instructions are not completely understood, or if in doubt as to whether the
tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected tools intended for use on a supply circuit having a
nominal rating less than 150 volts:
This tool is intended for use on a circuit that has an outlet that looks like the
one illustrated in Sketch A in Figure 1. The tool has a grounding plug that
looks like the plug illustrated in SketchA in Figure 1. A temporary adapter,
which looks like the adapter illustrated in Sketches B and C, may be used to
connect this plug to a 2-pole receptacle as shown in Sketch B if a properly
grounded outlet is not available. The temporary adapter should be used only
until a properly grounded outlet can be installed by a qualified electrician. The
green-colored rigid ear, lug, and the like, extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box.
3. Grounded, cord-connected tools intended for use on a supply circuit having a
nominal rating between 150-250 volts, inclusive:
This tool is intended for use on a circuit that has an outlet that looks like the
one illustrated in Sketch D in Figure 1. The tool has a grounding plug that
looks like the plug illustrated in Sketch D in Figure 1. Make sure the tool is
connected to an outlet having the same configuration as the plug. No adapter
is available or should be used with this tool. If the tool must be reconnected
for use on a different type of electric circuit, the reconnection should be made
by qualified service personnel; and after reconnection, the tool should comply
with all local codes and ordinances.
Note : In Canada, the use of a temporary adaptor is not
permitted by the Canadian Electrical Code.
GROUNDING
PIN COVER OF GROUNDED
OUTLET BOX
METAL SCREW
(A)
(B)
FIGURE 1
Grounding methods
Table1
Minimum gage for cord
Ampere Rating
Volta Total length of cord in feet
120V
240V
25ft. 50ft. 100ft. 150ft.
50ft. 100ft. 200ft. 300ft.
Not
More More
Than Than AWG
0 6
610
10 12
12 16
18 16 16 14
18 16 14 12
16 16 14 12
14 12 Not Recommended
ADAPTER
GROUNDING
MEANS
(C)
GROUNDING
PIN
(D)
Indice
Altri manuali Oliver Sega
Oliver
Oliver 5015 Manuale utente
Oliver
Oliver 5018 Manuale utente
Oliver
Oliver 4045 Manuale utente
Oliver
Oliver 4680 Manuale utente
Oliver
Oliver 4620 Manuale utente
Oliver
Oliver 4910 Manuale utente
Oliver
Oliver 4640 Manuale utente
Oliver
Oliver 4015 Manuale utente
Oliver
Oliver 4065 Manuale utente
Oliver
Oliver 4040 Manuale utente
