olympia electronics GR-290 Manuale utente
Page 1 from 5923292000_09_016
GENERAL
o
These devices are used indoors (ta 40 C) in
places where emergency luminaires are
needed. The luminaires GR-290 and GR-
292 are suitable for corridors lighting and
the GR-291 and GR-293 for open area
lighting. Each device must be permanently
connected to mains power supply. In
normal operation the battery is charging. In
case of a mains power supply failure the
device will light the illumination led
automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions οn page 2.
Battery Charging
The battery charging is completely
controlled. In this case, is achieved the
perfect battery maintenance , as well as
the elongation of its duration. When the
battery has completely charged, it charges
with a maintenance current.
Battery Cut-off
The device enters this mode when the
mains power supply fails and battery has
lost its energy. During this operation the
device enters the idle state and battery
consumption is negligible, in order to be
protected from deep discharge.
Manual Test
This test can be done by pushing the test
button. The light source and the emergency
circuit of the device is monitored. The
manual test can be conducted only if the
main power supply and the battery is
connected. During this test period all
indication LEDs are OFF.
Automatic Operational Test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the mains power supply and the
battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is
conducted and measures the device’s back
up operation and emergency duration. The
BATTERY FAULT LED blinks during the
measurement, indicating this process to the
user. This test is conducted automatically
every six months. In order to be performed,
the mains power supply and the battery
should be connected and fully charged. If
NON MAINTAINED SELF TESTING SPOT LIGHT
EMERGENCY LUMINAIRES WITH 1 WHITE POWER LED
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION
WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-MH)
CHARGE TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
220-240V AC / 50-60Hz
3 hours1.5 hour
24 hours
Deep discharge and overcharge protection
IP40
4.8V/1.2Ah
270lm 160lm
1 white power LED
o
5 to 40 C
Up to 95%
ABS/PC, PC
3 years (1 year for the battery)
435gr.
Ø125 x 65 mm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Charge, lamp fault, battery fault, TEST button
GR-290 GR-291 GR-292 GR-293
3.7W / 4.1 VA
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)
Thank you for your trust in our products
Olympia Electronics - European manufacturer
Page 2 from 5
the battery is not fully charged, the test is
postponed until the battery is completely
charged. If during this test, the autonomy is
less than the nominal then the battery fault
led turned on continuously and the battery
must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
Resetting Errors
Push the Test button for >10 seconds, to
delete all the indicated LED errors. Then
the device enters regular operation mode.
Test Switch
Pressing the test switch less than 5
seconds will initiate a light source test (last
for 3 secs). If the test switch is pressed for
more than 10 seconds, the device will be
reset (delete all errors).
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only.
2. The device must be connected to the
mai n s po w e r su p ply t h rou g h a f u s e
dependent by the total amount of the line’s
power load.
3. The replacement of the battery and the
light source must be done using parts of the
same type, by the manufacturer or by a
competent person.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s not allowed to discard batteries t i
into common trash bins, they must
b e d i s c a r d e d o n l y i n b a t t e r y
recycling points. Do not incinerate.
The light source contained in this
luminaire shall only be replaced by
the manufacturer, or his agent, or a
similar qualified person.
NOTE! The light source is non-user
replaceable.
INSTALLATION INSTRUCTIONS
32
Initial installation
1 Untighten the screw and pull up the reflector.
2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²
or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!
The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ
rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a
hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the
power terminal, connect the wires as shown in the picture and attach the power terminal (10A max).
3 Place the battery’s connector to the corresponding connector on the P.C.B.
4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire is ready
for mounting.
NOTE!! After finishing the installation you must power the luminaire for, at least, 24 hours for
battery charging to perform the nominal autonomy.
Cable
entry
hole L
N
1
923292000_09_016
Page 3 from 5
Mounting the lamp in suspended ceiling
Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):
Step 1
Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.
Step 2
Push up the luminaire, as shown in figure 2.
Step 3
Continue to push upwards until the lamp locks.
If you want to pull off the device, put a flat blade
screwdriver, between the device and the ceiling.
Figure 2
Figure 3
Figure 1
Ø110mm
Surface mounting
Install the luminaire according to the following steps:
Step 1. Follow the step 1 of the installation instructions.
Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling installation.
Step 3. (Figure )Drill 2 holes on the base 5 using a 4mm drill bit in order to permit the retaining screws to
pass. Mark these two drilled points on the required mounting location, drill the holes and install
the supplied plastic plugs. ATTENTION!! Especially for the GR-290 and GR-292 luminaire
installation on the ceiling you must align the base with the indications on the luminaire’s base.
Step 4. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to the
require location.
Step 5. Follow the steps 2,3 and 4 of the installation instructions.
Figure 4 Figure 5
Retaining fastener
Drill here
Indications
923292000_09_016
Page 4 from 5
Lamp fault
indication LED
GR-290, GR-292
GR-291, GR-293
ATTENTION!!!
During installation follow this light direction.
Corridor
lighting
Open
area
lighting
Important notice for the installed luminaires in one area !!!
The installer must connect the battery’s connector first and then should power the luminaire.
The time between batteries connection must be, at least 1.5 minute.
With this variation, it is ensured that the non synchronized Automatic Autonomous Test for
two or more luminaires installed in one area, is not conducted in the same day.
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Remove the luminaire from the suspended ceiling (figure 3).
2. Follow the step 1 of the installation instructions.
3. Disconnect the connector and remove the old battery.
4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in
the position of the old one.
5. Replace the removed parts (step 1 and 4) and power the device.
FAULT
LAMP
CHARGE TEST
BATT.
FAULT
LAMP
CHARGE TEST
BATT.
96
65
125
FAULT
LAMP
CHARGE TEST
BATT.
FAULT
LAMP
CHARGE TEST
BATT.
Battery
fault
indication
LED
Battery
charge
indication
LED
Figure 6
Test
button
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
60 °C max. across the board 45 °C max. across the board
Non reversible connection between main pcb and led module
3-3.2VDC
2.2W 1.1W
1110143 2704143
GR-290
GR-291
GR-292
GR-293
Status of LEDs
LEDs Description of indication
CHARGE : Battery charging, : battery charged, : disconnected or unfunctional battery
LAMP FAULT : Operation check, : lamp fault, : normal operation
BATT. FAULT : Autonomy test, : battery fault, : normal operation
Note : Blinking, : constantly on, : off
CAUTION : Do not view directly with bare eyes.
923292000_09_016
Page 5 from 5
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non maintained (*)
A: Including test device
90: 1.5 hour duration
180: 3 hours duration
(*) Non Maintained operation: The luminaire lights its illumination source, only in power
supply’s failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the
mains power supply or not.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
923292000_09_016
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali olympia electronics Lanterna
olympia electronics
olympia electronics GR-470 Manuale utente
olympia electronics
olympia electronics EASY LIGHT Series Manuale utente
olympia electronics
olympia electronics OLY-1004/WP/ADR Manuale utente
olympia electronics
olympia electronics GR-900/30L/SC Manuale utente
olympia electronics
olympia electronics GR-8/leds Manuale utente
olympia electronics
olympia electronics GRL-29 WP Manuale utente
olympia electronics
olympia electronics POWER LIGHT Series Manuale utente
olympia electronics
olympia electronics OLY-1004 Manuale utente
olympia electronics
olympia electronics GR-940/15L/MAR Manuale utente
olympia electronics
olympia electronics Power Light Series Manuale dell'operatore
olympia electronics
olympia electronics Slim Light Series Manuale utente
olympia electronics
olympia electronics GR-2110 Manuale utente
olympia electronics
olympia electronics GR-220/DUO/M Manuale utente
olympia electronics
olympia electronics GR-290/M Manuale utente
olympia electronics
olympia electronics GRL-37/90/ADR Manuale utente
olympia electronics
olympia electronics SLIM LIGHT Series Manuale utente
olympia electronics
olympia electronics CLASSIC LIGHT Series Manuale utente
olympia electronics
olympia electronics POWER LIGHT Series Manuale utente
olympia electronics
olympia electronics GRL-38/90/M Manuale utente
olympia electronics
olympia electronics GR-1935/15L Manuale utente
