Olympia electronics GR-470 Manuale utente

GENERAL

These devices are used indoors (ta 40 C)

in places where emergency luminaires are

needed. The luminaires GR-470 and GR-

472 are suitable for corridors lighting and

the GR-471 and GR-473 for open area

lighting. Each device must be permanently

connected to mains power supply. In

normal operation the battery is charging. In

case of a mains power supply failure the

device will light the illumination led

automatically in emergency mode. When

the mains power supply is restored the

device turns to normal operation.

INSTALLATION

To install the luminaire follow the

installation instructions οn page 2.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personel only.

2. The device must be connected to the

mains power supply thru a fuse dependent

by the total amount of the line’s power

load.

3. It is suggested to check every month the

indication LED for battery charging, and by

placing the test card (page 5) an (A-1900)

operation test is initiated, to check the

emergency cirquit. The illumination source

should light as long as the card is present.

In the opposite condition contact the

installer.

4. It is sugested to check every 6 months

the minimum autononous duration by

disconnecting the mains power supply.

Count the time that the luminaire lights and

in case of less time than the minimum

autonomous duration the battery must be

r e p l a c e d . I f the m e a s u r e d t i m e i s

considerably less than the minimum

autonomous duration contact the installer.

In c as e o f b at t er y o r l ig ht s ou rc e

replacement, these must be replaced by

parts of the same type, by the manufacturer

or by a competent person.

5. In case of inactive use for a period

greater than 2 months, disconnect the

ba tt ery by pul li ng o ut the ba tt ery ’s

connector.

6. I s not allowed to discard batteries in t i

to common trash bins, they must

be discarded only in battery

recycling points. Do not incinerate.

Page 1 from 5923473001_09_001

NON-MAINTAINED LUMINARIES

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

EXTERNAL DIMENSION

WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-Cd)

CHARGE TIME

INDICATIONS

BATTERY PROTECTION

MINIMUM DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

24 hours

Charge LED, Magnetic Test Contact

Deep discharge and overcharge protection

IP42

3,6V/1 Ah

1 white power LED

2,6W / 2,9VA

5 to 40 C

Up to 95%

3 years (1 year for the battery)

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

3 hour1,5 hour

145lm 80lm

470gr.

220-240V AC / 50-60Hz

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)

Thank you for your trust in our products.

Olympia Electronics - European manufacturer.

GR-470 GR-471 GR-472 GR-473

ABS/PC, PC

158 x 158 x 60,4mm (without decorative bezel)-195 x 195 x 60,4 (with decorative bezel)

Page 2 from 5

INSTALLATION INSTRUCTIONS

ATTENTION!!!

During installation follow this light

direction.

Corridor

lighting

Open

area

lighting

Cable

entry

hole

923473001_09_001

Initial installation

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the

four retaining screws without removing them and remove the diffusor.

2. Install the battery connector to its corresponding connector on the main pcb.

3. Install the cable grommet in the open hole of the plastic base and open a hole in the center of the

grommet using a small screw driver. Pass the power cable through the hole in the grommet (If

required, open another cutout cable entry hole and install the second supplied cable grommet).

Connect the cables as shown in the photograph. Use the supplied self adhesive pad and cable tie

to anchor the cable.

4. Reinstall the diffusor and re-tighten the 4 screws in a diagonally manner with a torque of 0,9 N*m.

NOTE!! After finishing the installation you must power the luminaire for at least 24 hours in

order to completely charge the batteries. The rated autonomous duration can be achieved

after this.

GR-470, GR-472 GR-471, GR-473

Page 3 from 5923473001_09_001

MOUNTING IN SUSPENDED CEILING

1 2

Required opening

14,5*14,5cm

plastic plugs plastic plugs

screws

plastic

mounting

bracket

luminary’s

base

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws (figure 1) without removing them and remove the diffusor.

2. Install the supplied cable grommet (figure 2).

3. Install the two plastic brackets with the four screws (figure 3).

4. Mark the positions of the mounting holes on the brackets.

5. Install the two supplied plaster board plugs by screwing them on the plaster board ceiling.

6.Open a cable entry cutout hole on the plastic base and follow step 3 in the “initial installation”

section.

7. Re-install the front cover that was removed in step 1.

8. Use the supplied screws to fasten the luminaire to the plaster board plugs (figure 8) that were

previously installed on the plaster board ceiling.

9. Finally, install the supplied decorative bezel (figure 9) and the notch on the bezel must be

located on the left side of the luminary (figure 10).

Page 4 from 5923473001_09_001

SURFACE MOUNTING

Other

possible

Cable entry

holes

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws without removing them and remove the diffusor.

2. Use a drill with a 3,5mm bit to open the 4 mounting holes (figure 2) located in the plastic base..

3. Place the luminaire on the desired mounting location and mark and drill these 4 holes. Fit the

supplied 4 plastic mounting plugs to these drilled holes on the mounting location.

4. If the cable entry hole is not suitable then use one of the supplied cables grommets to cover the

holes and open another cable entry cut out hole (figure 3). Follow step 3 of the “ initial installation

procedure”.

5. Mount the base to the desired location by using the supplied screws in each mounting

hole(figure 4).

6. Re-install the cover that was removed in step 1.

MOUNTING IN SUSPENDED CEILING

Olympia Electronics S.A.

5.6-6.6V DC

0205183

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non maintained (*)

A: Including test device

*90: 1.5 hour duration

180: 3 hours duration

(*) Non Maintained operation: The luminaire lights its illumination source, only in power

supply’s failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the

923473001_09_001

fixed connection between main pcb and led module

55 °C max. across the board

LED MODULE CHARACTERISTICS

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

TEST

A-1900

Manual TEST with the A-1900 Test card (not included

and is available only on request). In order to test the

device you must place the card in front of the indications

TEST mark and remove it instantly for TEST.

Page 5 from 5

GR-470

GR-471

GR-472

GR-473

CAUTION : Do not view directly with bare eyes

Battery replacement

It can be done only by a competent person and after the mains interruption.

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws without removing them and remove the diffusor.

3. Disconnect the connector and remove the old battery.

4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in

the position of the old one.

5. Replace the removed parts and power the device.

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

923473001_09_001

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

Page 5 from 5

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali olympia electronics Lanterna

olympia electronics

olympia electronics OLY-1004/WP/ADR Manuale utente

olympia electronics

olympia electronics KLIN-20/ST Manuale utente

olympia electronics

olympia electronics GR-8/leds Manuale utente

olympia electronics

olympia electronics GR-290 Manuale utente

olympia electronics

olympia electronics LLB-26/90 Manuale utente

olympia electronics

olympia electronics KLIN-20/ST/ADR Manuale utente

olympia electronics

olympia electronics OLY-1004 Manuale utente

olympia electronics

olympia electronics Power Light Series Manuale dell'operatore

olympia electronics

olympia electronics GR-900/30L/SC Manuale utente

olympia electronics

olympia electronics BAU LIGHT Series Manuale utente

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuale utente

olympia electronics

olympia electronics GR-427/12L/MAR Manuale utente

olympia electronics

olympia electronics GR-2110 Manuale utente

olympia electronics

olympia electronics Classic Light Series Manuale utente

olympia electronics

olympia electronics GRL-37/90/WP Manuale utente

olympia electronics

olympia electronics GR-8/leds Manuale utente

olympia electronics

olympia electronics Slim Light Series Manuale utente

olympia electronics

olympia electronics OLY-1024/WL Manuale utente

olympia electronics

olympia electronics WEATHER LIGHT Series Manuale utente

olympia electronics

olympia electronics GR-290/M Manuale utente

olympia electronics

olympia electronics GR-1935/15L Manuale utente

olympia electronics

olympia electronics GR-270 Manuale utente

olympia electronics

olympia electronics SLD-28/DZ Manuale utente

olympia electronics

olympia electronics GR-292/M/HL Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente

olympia electronics GR-470 Manuale utente

Manuali Lanterna popolari di altre marche