Olympia electronics GR-427/12L Manuale utente

GENERAL

These luminaires are used indoors (ta 40 C)

where emergency light is needed.

E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y

connected to mains power supply.

In normal operation the led strip lights and the

battery is charging.

In case of a mains power supply failure the

luminaire will light the led strip automatically

in emergency mode. When the mains power

supply is restored the device turns to normal

operation.

INSTALLATION

To install the luminaire follow the installation

instructions on page 4.

Battery Cut-off

The luminaire enters in this operation when the

mains power supply fails and battery has lost

its energy. During this operation the luminaire

enters the idle state and battery consumption is

negligible, in order to be protected from deep

discharge.

Battery charging

The battery charging is completely controled. In

this case, is achieved the perfect battery

maintenance , as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance

current.

Manual Test

The manual test can be conducted only if the

main power supply and the battery is connected.

By pressing the test button briefly an operation

test is initiated. During this test period all

indication LEDs are OFF.

Automatic test

This test includes all the operations that provide

the manual test and is conducted automatically

every 15 days. In order to be performed, the

main power supply and the battery should be

connected.

Automatic Autonomous Test

The Automatic autonomous Test is conducted

and measures the luminaire`s back up

operation. This test is conducted automatically

every six months. In order to be performed, the

main power supply and the battery should be

connected (the battery should be charged). If

the battery is not charged, the test is postponed

until the battery is completely charged. If during

the Automatic Autonomous Test the luminaire’s

duration is lower than the named, then the

battery must be replaced.

Back Up Operation

The autonomous duration of battery during

923427000_09_005

Page 1 from 5

GR-427/12L SELF TESTING MAINTAINED EMERGENCY LUMINAIRE

220-240V AC/50-60Hz

Bayblend FR3010, transparent polycarbonate

TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 5)

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (230V / EMERGENCY)

ILLUMINATION SOURCE

480 min

24h

Charge, lamp fault, fault indication LED, TEST button

From overcharge and full discharge

IP42

12 white LED’s

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

5 to 40 C

Up to 95%

3 years (1 year for the battery)

272 x 121 x 50 mm

600gr.

100lm / 100lm

3,6V/3Ah

3,5W / 7VA

Thank you for your trust in our products

Olympia Electronics - European manufacturer

Page 2 from 5

emergency mode is at least the one that is

stated in the list of the first page. During

emergency mode, a LED strip test is also

performed.

Resetting Errors

Push the Test button for 5 seconds, to

extinguish all the indicated LED errors. Then

the luminaire enters regular operation mode.

Indication LED status (with connected

mains power supply).

AC Charge

On: Good charge current.

Οff: No battery (No charging current

or disconnected battery).

Lamp fault

Οn: faulty LED strip.

Off: Good LED strip.

Fault

Οff: Battery OK.

Blink (With AC Charge LED ON): Autonomy or

low battery problem

(the battery must be replaced).

Blink (With AC Charge LED Off):

No charging current or disconnected battery.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel

only.

2. The device must be connected to the mains

power supply thru a fuse dependent by the total

amount of the line’s power load.

I n c a s e o f b a t t e r y o r l i g h t s o u r c e

replacement, these must be replaced by parts of

the same type, by the manufacturer or by a

competent person.

t i

in battery recycling

points. Do not incinerate.

3 .

4. In case of inactive use for a period greater

than 2 months, disconnect the battery by pulling

out the battery’s connector.

5. I s not allowed to discard batteries in to

common trash bins, they must be

discarded only

Suspended ceiling

Α-3018 mounting springs

Mounting methods

All luminaires, can be mounted either surface or in

suspended ceilings.

Suspended ceiling installation.

On the bottom of the base plastic of the luminaire there

are two H shaped cut outs. These are used to install

the A-3018 mounting springs.

1. With a sharp tool remove the appropriate plastic

pieces to fit the mounting springs. First place the edges

of the mounting spring to the respective holes and

install the one end of the coil to the support axis.

2. Install the other end of the coil to the other support

axis.

3. Bend the springs and place the luminaire to the

respective suspended ceiling’s hole.

The luminaire’s placement to the suspended ceiling

must be done after the connection with power supply

cables.

Mounting the luminaire

in a suspended ceiling

Required

opening in

a suspended

ceiling

260

110

923427000_09_005

Page 3 from 5 923427000_09_005

Installation methods

A-3018

Special mounting

springs for

suspended ceiling

installation

Mounting springs Α-3018

Wall or ceiling installation

Suspended ceiling installation

MARKING PANEL SP-115

A marking panel SP-115 can be installed on the

luminaire in 3 different locations. This marking

panel is installed perpendicular to the diffusor of

the luminaire, as shown in the pictures below.

The panel is pre-printed and has a plastic

accessory on each side that is used to fasten the

panel to the luminaires.

There are 2 arrow stickers that can be placed in

each side of the marking panel to point to the

desired direction.

Placing the SP-115 marking panel

Place the plastic mounting accessories of the

marking panel as shown in pictures.

A-3018

SP-115 marking panel

Suspended ceiling installation

with Α-3018 mounting springs

and SP-115 marking panel

Ceiling installation

with SP-115 marking panel

Wall installation with SP-115

marking panel

923427000_09_005

Page 4 from 5

45 6

INSTALLATION INSTRUCTIONS

Base plastic

Cable entry channels

Luminaire mounting holes

Diffusor

Reflector

Base plastic

1 To install the luminaire you must dismantle it to 3 parts.

2 Place a flat blade screwdriver in the area Α to release the diffusor’s

plastic hook.

3 Place a flat blade screwdriver in the area B to release the reflector’s

plastic hook.

4 Use the included mounting parts to mount the base plastic.

Pass the mains cable thru a cable entry channel. The luminaire must

be connected to a permanent electrical installation to ensure the

immobilization of the cable.

5 Place the battery’s connector to the corresponding connector on the

P.C.B.

6 Connect the mains cables to the respective detachable terminal

block. Ν for neutral, L for live wire and L1 for the maintained

operation. The L1 wire can be connected to an external switch to

control the maintained or non maintained operation of the luminaire.

For permanent maintained operation use two wires to power the

luminaire, Ν for neutral and L for live wire, and link the L and L1.

7 Refit the removed parts in steps 2 and 3 (mind the correct

orientation) and the luminaire is ready to operate.

External

switch

Link

Controled operation of the luminaire

Permanent maintained operation

L L

L1 L1

NOTE!!

After finishing the installation you must power the luminaire at least for 24 hours for battery

charging to perform the named autonomy.

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Follow the step 2 and 3 of the installation procedure.

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in

the position of the old one.

4. Follow the step 7 of the installation procedure and power the device.

923427000_09_005

Page from5 5

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

LED MODULE CHARACTERISTICS

Olympia Electronics S.A

45 °C max. across the board

8.4-9.9VDC

2.16W

0211163

GR-427/12L

Cable connection between main pcb and led module

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated safety sign

480: 8 hours duration

Note!! The installer should fill in, on the specification

label, the letter G if the luminaire is used as a safety

sign.

X 1 8 0A G

(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s

failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the mains

power supply or not.

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Indice

Altri manuali olympia electronics Lanterna

olympia electronics

olympia electronics Classic Light Series Manuale utente

olympia electronics

olympia electronics GR-938/15L Manuale utente

olympia electronics

olympia electronics BAU LIGHT Series Manuale utente

olympia electronics

olympia electronics GR-900/30L/SC Manuale utente

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuale utente

olympia electronics

olympia electronics GRL-29 WP Manuale utente

olympia electronics

olympia electronics GR-8/leds Manuale utente

olympia electronics

olympia electronics BAU LIGHT Series Manuale utente

olympia electronics

olympia electronics LLB-26/90 Manuale utente

olympia electronics

olympia electronics GR-2100/ST Manuale utente

olympia electronics

olympia electronics GR-470 Manuale utente

olympia electronics

olympia electronics GR-2110 Manuale utente

olympia electronics

olympia electronics Power Light Series Manuale dell'operatore

olympia electronics

olympia electronics GR-427/12L/MAR Manuale utente

olympia electronics

olympia electronics GRL-38/90/M Manuale utente

olympia electronics

olympia electronics Double Easy Light GR-391/L Manuale utente

olympia electronics

olympia electronics POWER LIGHT Series Manuale utente

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series Manuale utente

olympia electronics

olympia electronics GR-940/15L/MAR Manuale utente

olympia electronics

olympia electronics GR-490/WP Manuale utente

olympia electronics

olympia electronics GR-290 Manuale utente

olympia electronics

olympia electronics GR-939/30L/LT Manuale utente

olympia electronics

olympia electronics POWER LIGHT Series Manuale utente

olympia electronics

olympia electronics SLIM LIGHT Series Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente

olympia electronics GR-427/12L Manuale utente

Manuali Lanterna popolari di altre marche