Olympia electronics SLD-28/SP Manuale utente

Page 1 from 4922044006_09_024

SLD-34/SP SLD-44/SP

SLD-28/SP

220-240V AC/50-60Hz

24h

Overcharging and deep discharging protection

Charge LED, Lamp LED, Fault LED, Test Button

IP30

3.6V/1.5Ah

100lm /100lm 125lm /125lm

9.5 VA9 VA

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, EN 1838

5 to 40 C

up to 95%

Bayblend FR3010, aluminum, plexiglas

280x120x15mm

3 years (1 year for the battery)

790gr. 1110gr. 1580gr.

340x190x15mm 440x240x15mm

289x65x34mm

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)

SELF TESTING MAINTAINED EMERGENCY ILLUMINATION SIGNS WITH WHITE LEDs

GENERAL

The luminaire consists mainly from two Battery Cut-off

parts, the body, where all the electronics The luminaire enters in this operation when

are located and the lamp-head where the the mains power supply fails and battery

indication sign and the high efficiency has lost its energy. During this operation

LEDs are located. the luminaire enters the idle state and

battery consumption is negligible, in order

Maintained to non-maintained selection to be protected from deep discharge.

capability

Power on the device and press Manual Test

continuously the TEST button for 10 The manual test can be conducted only if

seconds, until the led strip turns off. the mains power supply and the battery is

Release the button and after a short connected. By pressing the test button

emergency test, the device operates as briefly an operation test is initiated. During

non maintained. If you want to restore the this test period all indication LEDs are

previous condition (maintained operation), OFF.

press continuously the TEST button for 10

seconds, until the led strip lights. Release Automatic Operatioanal Test

the button and after a short emergency This test includes all the operations that

test, the device operates as maintained provide the manual test and is conducted

illumination sign. automatically every 15 days. In order to be

performed, the mains power supply and

Battery Charging the battery should be connected.

The battery charging is completely

controled. In this case, is achieved the Automatic Autonomous Test

perfect battery maintenance , as well as the The Automatic Autonomous Test is

elongation of its duration. When the battery conducted and measures the luminaire`s

has completely charged, it charges with a back up operation. This test is conducted

maintenance current. automatically every six months. In order to

Thank you for your trust in our products

Olympia Electronics - European manufacturer

Operation temperature range

Relative humidity

Construction materials

External panel's dimensions

External unit’s dimensions

Typical weight

Guarantee

Mains voltage

Maximum power consumption

Battery (Ni-MH)

Recharging time

Battery protection

Indications

Minimum emergency duration

Degrees of cover protection

Produced in accordance with

Light source intensity (230V) / (emerg.)

Page 2 from 4 922044006_09_024

be performed, the mains power supply Indication LED status (with connected

and the battery should be connected (the mains power supply).

battery should be charged). If the battery

is not charged, the test is postponed until Charge

the battery is completely charged. If On: Charge current OK.

during the Automatic Autonomous Test the Οff: No battery (No charging current or

luminaire’s duration is lower than the disconnected battery).

named, then the battery must be Lamp Fault

replaced. Οn: Faulty LED strip.

Off: LED strip OK.

Back Up Operation

The autonomous duration of battery Battery Fault

during emergency mode is at least the Οff:Battery OK.

one that is stated in the list of the first Blink (With Charge LED ON): Autonomy

page. During emergency mode, a LED or low battery problem (the battery must

strip test is also performed. be replaced).

Blink (With Charge LED Off):

Resetting Errors No charging current or disconnected

Push the Test button for 5 seconds, to battery.

delete all the indicated LED errors. Then

the luminaire enters regular operation

mode.

INSTALLATION INSTRUCTIONS

General:

1. Operations for installation, maintainance or testing must be done by authorized

personnel only.

2. The device must be connected to the mains power supply through a fuse dependent

by the total amount of the line’s power load.

In case of battery or light source replacement, these must be replaced by parts of the

same type, by the manufacturer or by a competent person.

t i in battery recycling points.

Do not incinerate.

. In case of inactive use for a period greater than 2 months, disconnect the battery by

pulling out the battery’s connector.

5. I s not allowed to discard batteries in to common trash bins, they must be

discarded only

Remove the front plastic cover by unscrewing the two

retaining screws.

Pass the mains cables through the hole of the plastic base.

Connect the live and the neutral wires to the terminal block

as shown in picture.

Mount the device by installing the included mounting

accessories in the holes or use the Α-3018 mounting

springs for suspended seiling mounting.

Install LED strip and batery connectors to the appropriate

PCB connectors.

Refit the front plastic cover by srewing the two

removed screws in step 1, and power on the device.

NOTE!!

After finishing the installation you must power the device

at least for 24 hours for battery charging to perform

the nominal autonomy.

Page 3 from 4 922044006_09_024

In recess mounting installation the

required opening is 280 x 50 mm.

The material must withstand the

luminaires weight.

280

(*) Maintained operation: The luminaire lights its

illumination source, when it is powered by the mains power

supply or not.

Non Maintained operation: The luminaire lights its

illumination source, only in power supply’s failure.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

*180: 3hours duration

ATTENTION!!

To disconnect the panel’s cables, you have to power off the mains power supply and

disconnect the battery.

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Placing the mounting springs

Α-3018

Place one part of the mounting spring

first and then the other one.

Place the edges of the mounting spring

as shown in picture.

Recess mounting

in suspended ceiling

A-3018

Mounting springs

for recess mounting

A-3018 mounting springs

Ceiling mounting Wall mounting

Mounting methods

When the device is mounted externally it can use the A-1028 mounting box.

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Eginio Pierias Greece

www.olympia-electronics.gr

[email protected]

LED MODULE CHARACTERISTICS

Olympia Electronics S.A.

45 °C max. across the board

Cable connection between main pcb and led module

8.7-10.8V DC 0.975W

2312083

0.78W

0106163 1307083

SLD-28/SP

SLD-34/SP

SLD-44/SP

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Page 4 from 4 922044006_09_024

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali olympia electronics Attrezzatura di illuminazione

olympia electronics

olympia electronics GR-460/WP Manuale utente

olympia electronics

olympia electronics MLD-28D/w/MAR Manuale utente

olympia electronics

olympia electronics GR-460 Manuale utente

olympia electronics

olympia electronics GR-60 Manuale utente

olympia electronics

olympia electronics GR-940/15L Manuale utente

olympia electronics

olympia electronics GRL-37/90/WP/WL Manuale utente

olympia electronics

olympia electronics GR-415/4P Manuale utente

olympia electronics

olympia electronics KLD-30 Manuale utente

olympia electronics

olympia electronics ZLD-28/EM Manuale utente

olympia electronics

olympia electronics SLL-1001/WP Manuale utente

olympia electronics

olympia electronics WEATHER LIGHT Series Manuale utente

olympia electronics

olympia electronics GRL-29/WL Manuale utente

olympia electronics

olympia electronics GR-940/15L Manuale utente

olympia electronics

olympia electronics GR-316/15L/MAR Manuale utente

olympia electronics

olympia electronics GR-1938/4P Manuale utente

olympia electronics

olympia electronics GRL-37/90/WL Manuale utente

olympia electronics

olympia electronics LLB-26/CBS/24V/ADR Manuale utente

olympia electronics

olympia electronics GR-423/12L/MAR Manuale utente

olympia electronics

olympia electronics KLD-30/ST/ADR Manuale utente

olympia electronics

olympia electronics POWER LIGHT Series Manuale utente

olympia electronics

olympia electronics GR-938/4P/ADR Manuale utente

olympia electronics

olympia electronics GR-579/L/90/WP Manuale utente

olympia electronics

olympia electronics KLD-30/CBS/24V/ADR Manuale utente

olympia electronics

olympia electronics GR-292/M/HL/ADR Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente

olympia electronics SLD-28/SP Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche