One Remote 30017742 Manuale utente
PowerLink Switch
OneRemote Type 30017742
User Manual
30017742u2uk
www.oneremote.dk
2
Content
Modes of switching..............................................................................................................................3
Priority switching mode............................................................................................................ 4
Last source switched ON mode ................................................................................................ 6
Remote controlled switching mode ......................................................................................... 7
Features..............................................................................................................................................10
Galvanic isolation...................................................................................................................... 10
lossless audio pass .................................................................................................................... 10
Datalink pass............................................................................................................................. 10
delay at power off..................................................................................................................... 10
Installation .........................................................................................................................................11
Cable quality ............................................................................................................................. 11
Option Programming .........................................................................................................................12
Technical specifications .....................................................................................................................14
Connections .............................................................................................................................. 14
www.oneremote.dk
3
MODES OF SWITCHING
The OneRemote PowerLink Switch is developed for use with active (powered) B&O speakers
connected with PowerLink DIN cables. Use adaptor cables, if speakers or a source are equipped
with RJ45 connectors.
The PowerLink Switch makes it possible for two different sound sources to share one set of
PowerLink speakers.
The switch can be operated in one of three ways.
1. Priority switching. Factory default.
2. Last switched on source.
3. Remote controlled.
www.oneremote.dk
4
PRIORITY SWITCHING MODE
In the Priority Switching Mode both Inputs, PL1
and PL2, must connect to PowerLink compatible
sources or sources that include a switching power
trigger signal. PowerLink from Bang & Olufsen, Loewe Audio
Link or similar.
When one of the sources is powered on, sound
from this input will be routed to the output of the
switch. At the same time the speaker will power
on.
If both PL1 and PL2 sources are powered on, PL2
input will always be prioritized.
Refer to the chapter Option Programming to
program the PowerLink Switch to the Priority
Switching Mode, if it has been changed from the
factory setting.
PL1
PL2
Out
ON
OFF
PL1
ON
ON
PL2
OFF
ON
PL2
OFF
OFF
Speaker off
Example of use in the Priority Switching Mode.
BeoSound Encore and a Bang & Olufsen TV sharing BeoLab speakers.
www.oneremote.dk
5
Example of use in the Priority Switching Mode.
A NON Bang & Olufsen TV *1 and a BeoSound audio product sharing BeoLab speakers.
*1 The TV must have a regulated sound output and a trigger output signal, like a Loewe TV equipped with Audiolink.
www.oneremote.dk
6
LAST SOURCE SWIT CHED ON MODE
In the Last Source Switched ON Mode both
inputs, PL1 and PL2, must connect to PowerLink
compatible sources or sources that include a
power trigger signal. PowerLink from Bang & Olufsen,
Loewe Audio Link or similar.
When one of the sources is powered on, it
creates an event.
When an event occurs, sound from the source
that created the event will be routed to the
output of the switch. At the same time the
speaker will power on.
PL1
PL2
Out
POWER ON
OFF
PL1
ON
POWER ON
PL2
POWER ON
ON
PL1
OFF
OFF
Speaker off
The Last Source Switched ON Mode makes it possible to have both sources powered on at the
same time, selecting audio from either one.
Refer to the chapter Option Programming on how to select the Last Source Switching Mode.
Example of use in the Last Source Switching ON Mode.
BeoSound Encore and a Bang & Olufsen TV sharing BeoLab speakers.
www.oneremote.dk
7
REMOTE CONTROLLED SWITCHING MODE
In the Remote Controlled Switching Mode the PL1
and PL2 sources do not need to be PowerLink
compatible or include a switching power on trigger
signal.
A B&O remote controls the switching using a
connected IR-receiver. Any B&O Remote control
may be used.
Note that an infrared receiver is not included with
the switch.
Refer to the chapter Option Programming on how
to change to the Remote Controlled Switching
Mode.
The Remote Controlled Switching Mode is for
special use.
Each source key used in the set-up must be option
programmed. One by one.
Factory defaults
Remote Controlled Switching Mode
Source In
TV 1
DVD 1
DVD2 1
VAUX 1
VAUX2 1
VMEM 1
VMEM2 1
VTAPE 1
VTAPE2 1
DTV 1
DTV2 1
TEXT 1
Source In
RADIO 2
CD 2
CD2 2
AMEM 2
AMEM2 2
NMUSIC 2
AAUX 2
PHONO 2
NRADIO 2
Source In *1
LIGHT 0
STANDBY Speaker
OFF
*1
Sources programmed for INPUT-0 are ignored. As default setting the LIGHT
key has been set to input 0, so the switch will ignore the LIGHT key being
pressed. TV will select PL1 and RADIO will select PL2 and so on.
Default control with IR-receiver.
To suit the actual set-up it will most likely need
reprogramming of some keys.
B&O Remote
Control Key
Switch Output
TV
PL1
DVD
PL1
RADIO
PL2
…….
LIGHT
No change
STANDBY
Speaker off
www.oneremote.dk
8
www.oneremote.dk
9
Example of use in the Remote Control Switching Mode.
A B&O TV and an Apple Airport Express, Bluetooth receiver or DAB radio sharing BeoLab speakers.
www.oneremote.dk
10
FEATURES
GALVANIC ISOLATION
Using galvanic isolation the input signals are completely kept separated from each other.
This prevents problems with floating grounds and the two separate ground potentials for data and
audio.
Sound signals are switched with relays.
Data ground signal is switched with a relay.
Analog ground signal is switched with a relay.
Digital data signal flows via galvanic isolating optocouplers.
When power is not connected or in standby mode, sound output is muted with a mechanical relay.
LOSSLESS AUDIO PASS
The audio signals are passed without any modification; the output of the switch is the same that
enters the input.
DATALINK PASS
Datalink is passed to the output, from the selected input for display and other control.
DELAY AT POWER OFF
As the switching is controlled directly from the sources or an IR receiver, the speaker will power
off immediately, when no source is selected. When the speaker is powered off, sound signals will
be muted using a mechanical relay.
Indice
Altri manuali One Remote Interruttore
