Onkyo TX-RZ610 Guida all'installazione

Basic Manual

Hookup

Step1: Choose your Speaker Layout .......................................3

Step2: Connect the Speakers ..................................................9

Step3: Connect the TV ..........................................................11

Step4: Connect the AV Components .....................................13

Step5: Connect Other Cables ................................................17

Setup

Step6: Power On & Initial Setup ............................................18

HDMI Setup ...........................................................................19

Playback

Basic Playback ......................................................................20

Network Functions .................................................................21

Others ....................................................................................23

Part Names

Front Panel ............................................................................25

Rear Panel ............................................................................26

Remote Controller .................................................................27

Display ...................................................................................27

This manual includes information needed when starting up and also

instructions for frequently used operations. The "Advanced Manual" is

available on the internet with details about the playback features/

listening modes/settings details, specifications, and troubleshooting.

The Advanced Manual is created in a format that makes it easy to read

on a PC or Smartphone.

http://www.onkyo.com/manual/txrz610/adv/en.html

Advanced Manual found here

AV RECEIVER

TX-RZ610

> Before start > Hookup > Setup > Playback > Part Names

SN29402171_TX-RZ610_BAS_En_1602xx.book 1 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

What's in the box

1. Main unit 2. Remote controller (RC-911R)

×1, Batteries (AAA/R03) ×2

3. Indoor FM antenna ×1 4. AM loop antenna ×1 5. Speaker setup microphone ×1

6. Power cord ×1

Main features

This unit is connected between your TV and your AV components. To play, select the source with the input

selector. You can connect 7.1 channels of speakers to this unit, with 7 channels at 170 W (6 ohms, 1 kHz,

0.9%THD) per channel plus pre out jack for powered subwoofer.

Supports playback in Dolby Atmos format which provides 360e sound placement

The HDMI jack supports 4K video input and output. Jacks IN1 to 3 and OUT MAIN/SUB support HDCP2.2

HDMI CEC functionality: Control features such as linking input switching with the input selector and players

conforming to the CEC standard, switching audio output and volume using the remote controller of a CEC-

compliant TV, and automatically switching this unit to standby when the TV is turned off

HDMI Standby Through: Video and audio signals from AV components can be transmitted to the TV even if this

unit is in standby

ARC: Connection with an ARC-compatible TV is complete with one HDMI cable

Easy Initial Setup using onscreen guidance and On-Screen Display (OSD) showing operations on the TV

Internet radio and AirPlay via wired LAN or Wi-Fi (wireless LAN) and network features such as Music Server

that enables PC music file playback, USB playback, plus other playback features such as AM/FM radio and

BLUETOOTH

play

Playback formats supported by Music Server and USB include WAV, FLAC and DSD high-res source

Multi-zone Connection which allows you to play in the main room and listen in a separate room (ZONE 2)

Equipped with RS232 port, IR IN jack, and 12V TRIGGER OUT jack

We plan to provide support for the DTS:X audio format through a firmware update for this unit. Refer to our

website for more information.

CAUTION: Connect speakers with 6 Ω to 16 Ω impedance. The power cord must be connected only after

all other cable connections are completed.

0We will not accept responsibility for damage arising from the connection of equipment manufactured by

other companies.

SN29402171_TX-RZ610_BAS_En_1602xx.book 2 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

Step1: Choose your Speaker Layout

12 Front Speakers

3Center Speaker

45 Surround Speakers

6Powered Subwoofer

For 5.1-Channel System

This is a 5.1-channel system that is the basic surround

system. Front speakers output front stereo sound and a

center speaker outputs center sound such as dialogs and

vocals. Surround speakers create back sound field.

Powered subwoofer reproduces bass sounds and creates

rich sound field. The front speakers should be positioned

at ear height, while the surround speakers should be

positioned just above ear height. Center speaker should

be set up facing the listening position. Place the powered

subwoofer towards the front. Placing it between the center

speaker and a front speaker gives you a natural sound

even when playing music.

0The front speakers, center speaker, and surround

speakers are counted as 5 channels, and the powered

subwoofer is counted as 0.1 of a channel, giving us the

name 5.1ch system.

＊1: 22e to 30e, ＊2: 120e

Go To "Hookup" (

P9)

＊1

＊2



SN29402171_TX-RZ610_BAS_En_1602xx.book 3 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

(

P3)

78 Surround Back Speakers

For 7.1-Channel System (with

Surround Back Speakers)

This is a system with surround back speakers added to

the basic 5.1-channel system. The connection of surround

back speakers improves the sense of envelopment and

connectivity of sound created by the back sound field and

provides a more real sound field. You can select the Dolby

Atmos listening mode, which realizes the most up-to-date

3D surround sound, when the input format is Dolby

Atmos. With formats other than Dolby Atmos, you can still

create a sound field by outputting sound from the

surround back speakers when you select the Dolby

Surround listening mode. The optimal positioning is for

surround back speakers to be at ear height. Place the

surround speakers in a more slightly forward position than

you would in a 5.1-channel system.

0If you are including surround back speakers in the

setup, surround speakers are required.

＊1: 22e to 30e, ＊2: 90e to 110e, ＊3: 135e to 150e

Go To "Hookup" (

P9)

＊2

＊3

＊1



SN29402171_TX-RZ610_BAS_En_1602xx.book 4 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

3´ (0.9 m)

or more

(

P3)

78 Height Speakers

Choose one of the following:

Front High Speakers

Rear High Speakers

For 7.1-Channel System

(with Height Speakers-A)

This is a basic 5.1-channel system with the addition of

height speakers, either as front high speakers or rear high

speakers. Select which speakers to setup according to

the environment of the room. You can select the Dolby

Atmos listening mode (5.1.2 channel playback), which

realizes the most up-to-date 3D surround sound including

overhead sounds, when the input format is Dolby Atmos.

With formats other than Dolby Atmos, you can still create

a sound field by outputting sound from the height

speakers when you select the Dolby Surround listening

mode. Front high speakers or rear high speakers should

be situated at least 0.9 m higher than the front speakers.

Front high speakers should be situated directly above the

front speakers and the distance between the rear high

speakers should match the distance between the front

speakers. Both should be set up facing the listening

position.

＊1: 22e to 30e, ＊2: 120e

Go To "Hookup" (

P9)

＊1

＊2



SN29402171_TX-RZ610_BAS_En_1602xx.book 5 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

(

P3)

78 Height Speakers

Choose one of the following:

Top Front Speakers

Top Middle Speakers

Top Rear Speakers

For 7.1-Channel System

(with Height Speakers-B)

This is a basic 5.1-channel system using ceiling speakers,

for example, with the addition of height speakers, either

as top front speakers, top middle speakers, or top rear

speakers. Select which speakers to setup according to

the environment of the room. You can select the Dolby

Atmos listening mode (5.1.2 channel playback), which

realizes the most up-to-date 3D surround sound including

overhead sounds, when the input format is Dolby Atmos.

With formats other than Dolby Atmos, you can still create

a sound field by outputting sound from the height

speakers when you select the Dolby Surround listening

mode. Fit top front speakers on the ceiling forward of the

seating position, top middle speakers on the ceiling

directly above the seating position, and top rear speakers

on the ceiling behind the seating position. The distance

between each pair should match the distance between

the two front speakers.

0Dolby Laboratories recommends placing this type of

height speakers to obtain the best Dolby Atmos effect.

＊1: 30e to 55e, ＊2: 65e to 100e, ＊3: 125e to 150e

Go To "Hookup" (

P9)

＊1

＊2

＊3



SN29402171_TX-RZ610_BAS_En_1602xx.book 6 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

(

P3)

78 Height Speakers

Choose one of the following:

Dolby Enabled Speakers (Front)

Dolby Enabled Speakers (Surround)

For 7.1-Channel System

(with Height Speakers-C)

This is a basic 5.1-channel system using Dolby enabled

speakers, with the addition of height speakers, either as

Dolby enabled speakers (front) or Dolby enabled

speakers (surround). Select which speakers to setup

according to the environment of the room.

Dolby enabled speakers are special speakers designed to

face the ceiling so that sound is heard after bouncing off

the ceiling so that sound appears to be coming from

overhead. You can select the Dolby Atmos listening mode

(5.1.2 channel playback), which realizes the most up-to-

date 3D surround sound including overhead sounds,

when the input format is Dolby Atmos. With formats other

than Dolby Atmos, you can still create a sound field by

outputting sound from the height speakers when you

select the Dolby Surround listening mode. Place them

either above the front speakers or above the surround

speakers.

＊1: 22e to 30e, ＊2: 120e

Go To "Hookup" (

P9)

＊1

＊2



SN29402171_TX-RZ610_BAS_En_1602xx.book 7 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

12 Front Speakers (Bi-Amping)

3Center Speaker

45 Surround Speakers

6Powered Subwoofer

For Bi-Amping the

Speakers

It is possible to connect front speakers supporting bi-

amping to improve quality of the bass and treble. The

maximum number of channels available with this

connection is 5.1 because Bi-Amping speakers require

one amplifier for the tweeter jacks and one amplifier for

the woofer jacks. The effects and placements for

speakers are the same as the 5.1-channel plan that

doesn't use Bi-Amping speakers.

0If you connect to speakers supporting Bi-Amping,

speaker output in ZONE (

P16) is not possible.

＊1: 22e to 30e, ＊2: 120e

Go To "Hookup" (

P10)

＊1

＊2



SN29402171_TX-RZ610_BAS_En_1602xx.book 8 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

Step2: Connect the Speakers

1/2˝

(12 mm)

1 Speaker cable, 2 Subwoofer cable

in case of:

Pages 3 to 7

Connect 123456 for a 5.1-channel system. For a

7.1-channel system, select either surround back speakers

or height speakers, and connect 78. Up to two powered

subwoofers can be connected. The same signal is output

from each of the SUBWOOFER jacks.

Make sure the exposed wires of the speakers do not stick out of

the speaker terminals when connecting. If the exposed wires of

the speakers touch the rear panel or the + and – wires touch each

other, the protection circuit will be activated.

Setup

0The speaker configuration is set to

12345678 audio output by default. If there

are speakers you won't be connecting, you need to

change the settings in Initial Setup, "1. AccuEQ

Room Calibration" (

P18) so that the audio from

those speakers you are not connecting is sent to

other speakers.

SN29402171_TX-RZ610_BAS_En_1602xx.book 9 ページ２０１６年２月４日　木曜日　午後１時４４分

> Before start > Hookup > Setup > Playback > Part Names

1/2˝

(12 mm)

For high-

frequency

For low-

frequency

1 Speaker cable, 2 Subwoofer cable

in case of:

Page 8

Connect front speakers compatible with Bi-Amping

connection to the FRONT jacks and the SURROUND

BACK or HEIGHT jacks. Make sure you remove the

jumper bar fitted between the woofer jacks and tweeter

jacks of the front speakers. In case of Bi-Amping

connection, refer to the instruction manual of your

speakers. Up to two powered subwoofers can be

connected. The same signal is output from each of the

SUBWOOFER jacks.

Make sure the exposed wires of the speakers do not stick out of

the speaker terminals when connecting. If the exposed wires of

the speakers touch the rear panel or the + and – wires touch each

other, the protection circuit will be activated.

Setup

0Bi-Amping connection requires you to change

some settings. Select "Yes" in "Bi-Amp" in "1.

AccuEQ Room Calibration" (

P18) in the Initial

Setup.

SN29402171_TX-RZ610_BAS_En_1602xx.book 10 ページ２０１６年２月４日　木曜日　午後１時４４分

Altri manuali per TX-RZ610

Indice

Lingue:

Altri manuali Onkyo Ricevitore

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente