Optex VX Infinity Series Manuale utente
-1-
INSTALLATION INSTRUCTIONS
No. 59-1935-1
MULTI DIMENSIONAL OUTDOOR DETECTOR
MULTI DIMENSIONAL OUTDOOR DETECTOR
VX InfinityTM series
VX InfinityTM series
FEATURES
CONTENTS
VXI-ST Standard model with 2 PIR
WIRED MODEL
VXI-AM VXI-ST with anti-masking
VXI-DAM VXI-AM with micro-wave
The VX InfinityTM series provide highly reliable detection functions, reducing false reports or
report losses. The VX InfinityTM series deliver stable detection performance even in severe
outdoor environments.
-12 m (40 ft.) by 90 degree flexible detection pattern adjustable to 5 ranges
- SMDA Logic for advanced temperature compensation and environmental noise immunity.
- Easy Masking for over spill prevention
- Double Conductive Shielding against bright light disturbance.
- Conduit/TX-Battery Case for both wired and wireless-ready models.
BASIC FEATURES
- Active IR Anti-Masking for detecting covering objects
- Tough Mod Dual Technology based on OPTEX gold-plated microwave module
OPTIONAL FEATURES
INTRODUCTION
1-1 BEFORE INSTALLATION
1-2 PARTS IDENTIFICATION
1-3 DETECTION AREA
INSTALLATION
2-1 BEFORE MOUNTING
2-2 WALL TAMPER WRS-02 (OPTION)
2-3 MOUNTING
2-4 MOUNTING WITHOUT BACK BOX
2-5 MOUNTING WITH BACK BOX
2-6 WIRING
2-7
PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)
2-8 AREA ANGLE ADJUSTMENT
1
2
2
3
4
4
4
5
5
6
7
7
8
8
9
10
12
13
14
14
15
3
4
5
6
7
2-9 AREA MASKING
2-10 DETECTION LENGTH ADJUSTMENT
SWITCH SETTING
WALK TEST
LED INDICATION
SPECIFICATIONS
6-1 SPECIFICATIONS
6-2 DIMENSIONS
SETTING OF SPECIAL DETECTION AREA
-2-
Warning
INTRODUCTION
1
1-1 BEFORE INSTALLATION
Warning
Caution
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
• Sunlight and reflection • Heat source • Objects moving in the wind
0.8 – 1.2 m
(2.64 – 3.94 ft)
Parallel
Tilt
Do not remove the PCB. Keep product away from direct splash.
Mounting height. Keep the detector parallel to the
ground.
Consider the direction a person is
approaching from, as well as the
detection area.
Install the detector in a place where it is free from false alarm factors. For example:
-3-
Cover unit
Main unit
Back box
Back box cap
Wiring sponge
Mounting plate
1-2 PARTS IDENTIFICATION
-Precautions for installing two or more sensors
Masking seal × 3 pcs
For wall mounting
Screw kit
Screw (4 × 20 mm)
Optional accessories
Wall tamper (WRS-02) PLUG-IN EOL (PEU)
1.0 m (3.28 ft) or more Less than 1.0 m (3.28 ft)
Do not install two or more VXI-DAMs in side by side or face to face. Doing so may cause
malfunction. VXI-DAM may be installed in back to back. If mounting on the same wall, make
sure that each unit is at least 1.0 m (3.28 ft) apart from the other.
VXI-ST
VXI-AM
VXI-DAM
-4-
a
b
c
d
e
fghi
j
l
m
n
k
INSTALLATION
2
1-3 DETECTION AREA
2-1 BEFORE MOUNTING
Control panel Wall tamper (option)
WRS-02
Twist and swage
the wires.
TOP VIEW
SIDE VIEW
Length limiting position 1 (Default)
PIR
MW
Area diagram of horizontal position D
12m
12m 10m 12m10m5m 5m0
10m
5m
0
D
ABCEFG
WRS-02 (option)
1m
0 5m 10m 12m
Length limiting position 2
1m
0 5m 10m 12m
Length limiting position 3
1m
0 5m 10m 12m
Length limiting position 4
1m
0 5m 10m 12m
Length limiting position 5
1m
0 5m 10m 12m
Note>>
The maximum detection length may vary as
shown below due to environment conditions.
Remove the cap.
1Open the cover unit.
2Remove the main unit from
the back box.
3Remove the back box
from the mounting plate.
4
Mount the wall tamper (WRS-02)
on the back of the main unit.
1Run the wire along the wiring
groove.
2Install the unit on the terminal block
and control panel.
3
Store the connecting
cable in a trench
and seal with a label
already in place.
2-2 WALL TAMPER WRS-02 (OPTION)
-5-
2-3 MOUNTING
Mount the mounting plate.
2-4 MOUNTING WITHOUT BACK BOX
The unit is installed without a back box unless the main unit requires a protrusion off the mounting wall.
Mount the main unit on the mounting plate.
Wall mount Pole mount
Electric gang box mount Conduit installation
Metal band
* Use a metal band with
25 mm or less in width.
Pitch 83.5 mm (3.29 inch)
An electric gang box can be connected. Open the knockout located at
the bottom of the back box.
Connect the pipe and back
box.
When mounting to electric gang
box (single), follow wall mount
instructions.
Wiring hole
Wiring hole
Wiring hole
Wiring sponge
Note>>
Pay attention to warterproof.
Note>>
It is optional to use the Backbox in hardwired models.
ø 21 mm
2-6
Proceed to
-6-
2-5 MOUNTING WITH BACK BOX
When a certain distance from the mounting surface is required for purposes such as avoiding an
unwanted object, use the back box to install the unit.
Open a wiring knockout on the back box and pass the wire from the mounting plate.
Wiring
Put the top of the back
box on the hook.
Wiring hole
Wiring sponge
Wiring sponge
1.
2.
3.
Wiring hole
1Open a wiring knockout inside the back box.
2Mount a back box on the mounting plate.
3Mount the main unit on the back box. 4Put the cap on top.
-7-
2-6 WIRING
-Power cable length
The power cable should be limited to the following length.
Wiring terminal is located on the upper part of the main box.
-When setting the resistance value using PLUG-IN EOL
Three types of signals - ALARM,
TROUBLE, and TAMPER - can be
recognized through the combination
of the resistance value and wires for
the TR, COM, and TP terminals.
-When setting the resistance value without
using PLUG-IN EOL
Wire resistors between the appropriate terminals as follows:
This feature may be used when connecting VXI to a control panel that supports the EOL technique.
Terminals <VXI-ST>
Power (+)
Power (-)
Spare
Spare
Alarm
Alarm
Tamper
Tamper
Aux. input
Aux. input
<VXI-AM> <VXI-DAM>
Power (+)
Power (-)
Spare
Trouble
Common
Alarm
Tamper
Tamper
Aux. input
Aux. input
WIRE GAUGE
AWG22
(0.33mm2)
290 m
(950 ft)
620 m
(2,030 ft)
240 m
(790 ft)
520 m
(1,710 ft)
160 m
(520 ft)
360 m
(1,180 ft)
12 V
VXI-ST VXI-AM VXI-DAM
Current draw 20 mA Current draw 24 mA Current draw 35 mA
14 V 12 V 14 V 12 V 14 V
450 m
(1,480 ft)
980 m
(3,220 ft)
380 m
(1,250 ft)
820 m
(2,690 ft)
260 m
(850 ft)
560 m
(1,840 ft)
720 m
(2,360 ft)
1,570 m
(5,150 ft)
600 m
(1,970 ft)
1,310 m
(4,300 ft)
410 m
(1,350 ft)
900 m
(2,950 ft)
AWG20
(0.52mm2)
AWG18
(0.83mm2)
COMMON
TROUBLE
ALARM
TAMPER
Type
Insert direction
A
Caution>>
For details, refer to a note provided with plugs. Make sure to apply the
correct type of plug according to the system
+ - SP TR COM AL TP TP
Triple-EOL
Double-EOL
TAMPER
ALARM
TROUBLE
PLUG-IN EOL
CONTROL PANEL
+ - SP TR COM AL TP TP
TAMPER
ALARM
TROUBLE
2-7 PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)
-8-
2-8 AREA ANGLE ADJUSTMENT
2-9 AREA MASKING
Note>>
When creating a special detection area, refer to the end of this manual.
If there is an unwanted object within the detection area, apply an area masking label to the appropriate area.
Insert the protruding
part of the cover into
the lens hole.
Fit the edge of the
lens.
Slide the lens holder to secure it.
Horizontal position D
(Default)
Horizontal position B
(F: symmetrical
position)
Horizontal position C
(E: symmetrical
position)
Horizontal position A
(G: symmetrical
position)
D
ABCEFGD
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
or
or
or
Unwanted
object (Tree)
1Slide the lens holder and remove the lens holder out
of the cover as shown below. 2Identify positions to mask on the lens and apply a
corresponding strip from the masking sheet 1.
3Insert the lens into the cover. 4Mount the lens holder to the cover.
The angle can be adjusted in
7 levels from A to G.
The detection area becomes
14 zones only when A or G is
selected.
-9-
2-10
DETECTION LENGTH ADJUSTMENT
Both upper and lower detection
area are blocked
IMPORTANT
BOTH DETECTION AREAS MUST BE
BLOCKED FOR DETECTION
Detection!
NO
Detection
NO
Detection
Only upper detection area is blocked
Only lower detection area is blocked
MW sensitivity
adjustment knob
1Adjust the PIR detection length by sliding the lower
PIR to the desired position.
2Adjust the MW detection length by rotating the MW
sensitivity adjustment according to the PIR area.
Detection length setting chart
* The detection lengths described above should be used as a guideline.
Position
1
(Factory
default)
2
3
4
5
12.0 m
(40.0 ft)
8.5 m
(27.9 ft)
6.0 m
(19.7 ft)
3.5 m
(11.5 ft)
2.5 m
(8.2 ft)
10.0 -17.0 m
(32.1 - 55.8 ft)
7.0 - 12.0 m
(23.0 - 39.4 ft)
5.0 - 8.5 m
(16.4 - 27.9 ft)
3.0 - 6.0 m
(9.8 - 19.7 ft)
2.0 - 3.5 m
(6.6 - 11.5 ft)
Max detection length Detection area
MW
sensitivity
adjustment
12 m
8.5 m
6 m
3.5 m
2.5 m
-10-
DIP switch
1 LED
2 ALARM OUTPUT
3 AUX INPUT
4 ANTI-MASKING
5 MICROWAVE IMMUNITY
SWITCH SETTING
3
1
ON
2 4 53
ON
12345
DIP switch 1
OFF ⇔ON
-LED
VXI-ST
VXI-AM
VXI-DAM
POSITION FUNCTION
ON
(Factory default)
OFF
LED ON
LED OFF
DIP switch 2
N.C. ⇔N.O.
-ALARM OUTPUT
VXI-ST
VXI-AM
VXI-DAM
ON
12345
POSITION FUNCTION
N.O.
N.C.
(Factory default)
N.O. output
N.C. output
VXI features can be set on/off by DIP switch settings.
MW sensitivity adjustment
PIR sensitivity selector
Altri manuali per VX Infinity Series
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Optex Sensore di sicurezza
Optex
Optex Fiber SenSys Laser Defender LD308SH Istruzioni per l'installazione e il funzionamento
Optex
Optex AP-360BR Manuale utente
Optex
Optex CX-702RS Manuale utente
Optex
Optex RLS-3060 Manuale utente
Optex
Optex AX-330PLUS Manuale utente
Optex
Optex FX-50QZ Manuale utente
Optex
Optex AIR-SLIDE T Manuale utente
Optex
Optex Redwall LRP 180QH Istruzioni per il montaggio
Optex
Optex Fit Series Manuale utente
Optex
Optex AX-350DH MK III Manuale utente
Optex
Optex VX-402R Manuale utente
Optex
Optex FlipX Series Manuale utente
Optex
Optex FTN-R Manuale utente
Optex
Optex VX-402 Manuale utente
Optex
Optex X-ZONE Manuale utente
Optex
Optex HX-80N Manuale utente
Optex
Optex PROWAVE AIR-SLIDE 2 Manuale utente
Optex
Optex OVS-50TNR Manuale utente
Optex
Optex REDSCAN mini-Pro Series Manuale di servizio
Optex
Optex OVS-01GT Manuale utente
