Optoma ALR100 Guida all'installazione

1

彈簧

Parts:

ALR100 Slim Framed Type

Assembling Instructions

Main (inner) frame x 4 Outer frame x 4

L Shape metal parts x 4 Wall hanging parts x 2

M5 x 15 mm screw x 8 M5 x 8 mm screw x 16

Adjusting screw x 2 Springs x N units (depends on sizes)

Screw for wall hanging parts x 4 Plastic plugs x 4

2

Assembling Instruction

Step1 Unpack the box on an empty large table top or clean floor.

Place PE film on the ground or table top and set L shape metal parts, main frame parts ready for

assembling.

3

Step 2

Assemble the main frames with L shape metal parts and M5 x 8mm screws

(Screw the four corners first but do not make to tight initially, then screw the main frame tight after it is

fully adjusted and matched).

Main frame assembled

Step3

Screen assembling: Take out screen sheet from paper tube.

4

Put synthesized paper on the ground or table top and roll out the screen.

Step 4

Put the assembled main frame set onto the screen and adjust it to be in a centered position of the

screen; spring the four corners first and do the rest from long to short sides of the frame accordingly

(please slightly press the main frame while springing the screen, to avoid film-slip causing unevenness

of each side/corner).

Please match the screen with the lines of the main

frame (red arrow marks)

5

Set springs symmetrically (long side to long size and short side to short side) and keep frame and

screen centered before springs all hooked-on.

6

Step 5

Make sure the outer frames are 45 degrees matched with main frame and screw M5 x 15mm screws;

outer frames can be slightly adjusted for smooth corner purpose.

Total Assembling Complete

7

Step 6

Assemble wall hanging parts and hang the frame afterward (better to hold the main frames when moving

the frame up and down). It is recommended to set the height between screen bottom and the ground to

be 110cm~120cm for better projecting performance.

If the wall is uneven, users may adjust the position between frame and wall by using adjusting screws.

Attention:

Please make sure the screen is not hanged upside

down by checking the “DOWNSIDE” label.

Altri manuali Optoma Accessori per proiettori

Optoma

Optoma OWM3000 Manuale utente

Optoma

Optoma WPS Manuale utente

Optoma

Optoma EP731 Manuale utente

Optoma

Optoma WS-9211G Manuale utente

Optoma

Optoma 3D-XL Manuale utente

Optoma

Optoma BX-AL133B Manuale utente

Optoma

Optoma BM-3300ST Manuale utente

Optoma

Optoma BX-AL133 Manuale utente

Optoma

Optoma A16 Manuale utente

Optoma

Optoma OWM1000 Manuale utente

Optoma

Optoma CM-E75X Manuale utente

Optoma

Optoma PCT-101 Manuale utente

Optoma

Optoma Projector Manuale utente

Optoma

Optoma AKPro Manuale utente

Optoma

Optoma ZF2100 Glasses Manuale utente

Optoma

Optoma UHDCast Pro Manuale rapido

Optoma

Optoma 3D-RF System Manuale utente

Optoma

Optoma DS-9106MGA Manuale

Optoma

Optoma TX778W Manuale utente

Optoma

Optoma BM-9005U Manuale utente

Optoma

Optoma A16 UST Series Manuale utente

Optoma

Optoma BM-5001U Guida

Optoma

Optoma 3D-XL Manuale tecnico

Optoma

Optoma BX-AL133B Manuale utente

Manuali Accessori per proiettori popolari di altre marche

PEERLESS

PEERLESS PE 1120 Guida

Osram

Osram SIRIUS HRI Series Manuale

Presentation Switchers

Presentation Switchers PS111 Manuale utente

Kramer

Kramer VIA GO Manuale utente

Yamaha

Yamaha PJL-112 Manuale elenco delle parti

Swedstyle

Swedstyle CL23AA02ZA25E Manuale utente

Mitsubishi Electric

Mitsubishi Electric 236CB Manuale del proprietario

Epson

Epson BrightLink 475Wi Manuale utente

Acer

Acer WP100 Manuale utente

i3

i3 i3board Manuale utente

CHIEF

CHIEF HB-43E Manuale utente

Biamp

Biamp Modena Hub Manuale di servizio

NEC

NEC MP10RX Manuale utente

Panamorph

Panamorph DCR-S3 Manuale utente

Exact solutions

Exact solutions FRAME-EVO-P10 Manuale utente

CHIEF

CHIEF VCM103S Manuale utente

InFocus

InFocus LP70+ Guida

Sharp

Sharp AN-PH20EZ Manuale utente