Overland Storage ARCvault Series Manuale utente

Introduction

This document describes how to remove and replace a

drive cover assembly on any Overland Storage ARCvault

unit. There are three different types of drive covers:

•2-port cover for a single SCSI drive in the drive bay

•4-port cover for dual SCSI drives in the drive bay

•Fibre Channel (FC) cover for a FC drive

Each drive cover comes complete with a new fan assembly.

Early versions of the ARCvault 12 and 24 featured a SCSI

drive cover (Figure 1) with only a single bus. The newer

drive covers now feature independent buses.

Figure 1. ARCvault 12 and 24 Original Drive Cover

NOTE: If replacing an older single bus drive cover on an

ARCvault 24 with a newer 4-port SCSI drive cover and you want

to retain the daisy-chain configuration for your network, an

optional jumper cable is needed (available separately).

Unpacking

Carefully unpack and verify that you have all the parts:

•Spare drive cover assembly (verify you have the

correct one for your system’s configuration)

•These remove & replace instructions

WARNING: To reduce the risk of electric shock or

damage to equipment, disconnect the power by

unplugging the power cord.

The design of the drive cover makes it easy to change it out

while the ARCvault unit is still mounted in a rack

(Figure 2).

Figure 2. Drive Cover Assembly Locations and Cabling

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD), observe standard ESD precautions.

ARCvault Series

SCSI/FC Drive Cover Spare

Remove & Replace Instructions

Overview & Notes

ARC-0105

ARC-0013

ARC-0077

ARC-0075

SCSI CableTerminator

Thumbscrews

SCSI Cables

Terminators

ARC-0087

FC Cable

Thumbscrews

Original Drive Cover:

Dual SCSI Drive Cover:

FC Drive Cover:

Prepare the Library

1. From the Operator Control Panel (OCP), press Power

> Power Off Library > OK (at the power down

message) to power down the unit.

2. After the unit has shut down, remove the power cord.

3. At the rear, remove the SCSI cable and terminator

from the drive cover.

Replace the Drive Cover

1. Loosen the two thumbscrews on the drive cover.

2. Remove the drive cover as follows:

a. Gently pull the drive cover out and hold it about

2 inches (5cm) below the drive bay (Figure 3).

b. Unplug the fan wiring from the fan connector.

c. Using the guide handles, pull the assembly out

about 1 inch (2.5cm) and unplug the SCSI cable

from the drive.

d. Set the old cover aside.

Figure 3. Removing an Original Drive Cover

3. Install the new drive cover as follows:

a. Holding the drive cover below the drive bay opening,

plug in the fan connector.

b. With the drive assembly still pull slightly out, attach

the SCSI drive cable to the drive (Figure 4).

c. Slide the assembly the rest of the way into the drive

bay.

Figure 4. Installing a Drive Cover for a Single Drive

4. Carefully reseat the drive cover and tighten the two

thumbscrews.

IMPORTANT: Be sure all drive wiring is secure in the space

behind the drive assembly and not caught between the

drive cover and the unit when reseating the cover.

5. Reconnect the SCSI cable and terminator to the

drive cover ports.

6. Plug in the power cord and power on the unit.

7. Check the fan to verify it is working.

Prepare the Library

1. From the Operator Control Panel (OCP), press Power

> Power Off Library > OK (at the power down

message) to power down the unit.

2. After the unit has shut down, remove the power cord.

3. At the rear, remove the SCSI cables and terminators

from the drive cover.

Replace the Drive Cover

1. Loosen the two thumbscrews on the drive cover.

2. Remove the drive cover as follows:

a. Gently pull the drive cover out and hold it about

2 inches (5cm) below the drive bay (Figure 5 on

page 3).

b. Unplug the fan wiring from the fan connector.

c. Using the guide handles, pull the assembly out

about 1 inch (2.5cm) and unplug the SCSI cables

from the drives.

d. Set the old cover aside.

Single Half-Height SCSI Drive

ARC-0044

SCSI

Fan

Connector

Cable

Drive

Cover

Guides

ARC-0120

SCSI

Fan

Connector

Cable

New Drive

Cover

Guides

Dual Half-Height SCSI Drives

Figure 5. Removing an Original Drive Cover

3. Install the new drive cover as follows:

a. Holding the drive cover below the drive bay opening,

plug in the fan connector.

b. With the drive assembly still pull slightly out, attach

the SCSI drive cables to the drives (Figure 6).

c. Slide the assembly the rest of the way into the drive

bay.

4. Carefully reseat the drive cover and tighten the two

thumbscrews.

IMPORTANT: Be sure all drive wiring is secure in the space

behind the drive assembly and not caught between the

drive cover and the unit when reseating the cover.

Figure 6. Installing New Single SCSI Drive Cover

5. Reconnect the SCSI cables and terminators to the

drive cover ports.

NOTE: If using a daisy-chain layout, connect a SCSI jumper

cable (not supplied) between the 2nd and 3rd ports.

6. Plug in the power cord and power on the unit.

7. Check the fan to verify it is working.

Prepare the Library

1. From the Operator Control Panel (OCP), press Power

> Power Off Library > OK (at the power down

message) to power down the unit.

2. After the unit has shut down, remove the power cord.

3. At the rear, remove the FC cable from the drive port.

Replace the Drive Cover

1. Loosen the two thumbscrews on the drive cover.

2. Remove the drive cover as follows:

a. Gently pull the drive cover out and hold it about

2 inches (5cm) below the drive bay (Figure 7).

b. Unplug the fan wiring from the fan connector.

c. Set the old cover aside.

3. Holding the new drive cover below the drive bay

opening, plug in the fan connector.

Figure 7. Installing a New FC Drive Cover

ARC-0043

SCSI

Fan

Connector

Cable

Drive

Cover

Guides

ARC-0107

SCSI Fan

Connector

Cables

New Drive

Cover

Guides

Single Full-Height FC Drive

ARC-0069

Fan

Connector

Drive

Cover

Guides

4. Carefully reseat the drive cover and tighten the two

thumbscrews.

IMPORTANT: Be sure all drive wiring is secure in the space

behind the drive assembly and not caught between the

drive cover and the unit or blocking the port access hole

when reseating the cover.

5. Reconnect the FC cable to the drive port.

6. Plug in the power cord and power on the unit.

7. Check the fan to verify it is working.

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained

therein are held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that

no right is conveyed to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any

kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the

product(s) or program(s) described in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com,

or call 1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or

+1 (858) 571-5555 Option 5 (International).

Altri manuali per ARCvault Series

Indice

Altri manuali Overland Storage Magazzinaggio

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage Neo Series 2000 Manuale utente

Overland Storage

Overland Storage SnapServer Manuale di servizio

Overland Storage

Overland Storage Snap Server 210 Manuale utente

Overland Storage

Overland Storage ARCvault 2U Series Manuale utente

Overland Storage

Overland Storage SnapSAN S3000 Manuale di servizio

Overland Storage

Overland Storage Ultamus Raid 1200 Manuale utente

Overland Storage

Overland Storage NEO XL Series Manuale utente

Overland Storage

Overland Storage LoaderXpress Guida

Overland Storage

Overland Storage LTO-4 Manuale utente

Overland Storage

Overland Storage NEO 2000e Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage LTO-5 Manuale utente

Overland Storage

Overland Storage NEO XL Series Manuale

Overland Storage

Overland Storage SnapServer DX1 Manuale utente

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage NEOxl 40 Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage ULTAMUS RAID 4800 Manuale utente

Overland Storage

Overland Storage E Series Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage NEO 200S Manuale utente

Overland Storage

Overland Storage NEO Series Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente