Overland Storage NEO 8000 Manuale utente

This document describes how to unpack and set up a new

NEO 8000 Library. This same information is also found in

the Overland NEO 8000 Library User Guide.

WARNING: Due to the weight and size of the library, it

is recommended that at least two people be involved

with the unpacking process.

CAUTION: Read and become familiar with the entire

document before starting this unpacking procedure.

Steps performed out of sequence may cause damage to

the library which voids existing warranties.

NOTE: Retain all packaging materials in a protected place in

case the library needs to be shipped to a different location.

Tools Needed

These tools are required to unpack the library:

•9/16” wrench

•10” adjustable wrench

•Level tool

•Large flat-blade offset screwdriver

•Box knife

•#2 Phillips screwdriver

1. Position the shipping container on a level surface with

adequate clearance to work around it (Figure 1).

NOTE: The container pallet is labeled “RAMP SIDE” on each

corner of the removal side.

•Allow at least 10 ft. (3.0m) of clearance on the

removal side of the container

•Allow about 3 ft. (1.0m) of clearance around the other

three sides of the container

•Allow at least 8 ft. (2.5m) of vertical clearance

Figure 1. Unpacking Space Requirements

NEO 8000™ Library

Important Unpacking

Instructions

Overview & Notes

Removing the Outer Carton

NEO-8117`

Ramp (Front)

Floor

Allow at least 10 ft. (3.0m)

to remove the library

from the pallet.

Allow 3 ft.

(1.0m) around

the library

Allow 8 ft.

(2.5m) vertical

clearance

2. Remove the outside packaging (Figure 2).

a. Cut the three (3) shipping straps and remove.

b. Remove the six (6) shipping strap reinforcing

corners from around the box.

c. Remove the top cap.

d. Release and remove each of the eight (8) plastic

retainers (four each on opposite corners).

Figure 2. Library Packaging Components (Rear View)

e. Remove the two (2) large pieces of cardboard

surrounding the library.

3. Remove the inner packaging (Figure 3).

a. Remove the two (2) pads on top of the library.

b. Remove the Ramp and Door boxes and set them

aside.

c. Remove the plastic sheet that covers the library.

Figure 3. Ramp and Door Box Locations

1. Remove the ramps from the Ramp box and lay them

down, placing the brackets into the corresponding slots

in the pallet (Figure 4).

Figure 4. Placing the Ramps in Position

2. Remove the rear hardware holding the library on the

pallet.

a. To provide access to the hold-down bolts and leveling

legs, remove the rear door of the library; set aside.

b. Remove the four (4) crossbar screws from the pallet.

c. Remove the rear crossbar (Figure 5).

Figure 5. Removing the Rear Crossbar

d. Using the 9/16” wrench, remove the two bolts and

hold-down brackets.

e. Use the 10” adjustable wrench to loosen and raise

the two leveling legs (Figure 6 on page 3).

NEO-8113

Plastic

Strap

Corners

Reinforcing

Shipping

Retainers

Straps

Top Cap

NEO-8144

Ramp Box

(Library hidden for clarity)Front

Top Pads

Door Box

Detaching the Pallet

NEO-8115

(Library hidden for clarity)

Slots

Ramps

Crossbar Screws

NEO-8116

Front Crossbar

Bolts

(Library hidden for clarity)

Rear Crossbar

(Remove First)

Figure 6. Raising the NEO 8000 Leveling Legs

3. Remove the front hardware holding the library on the

pallet.

a. Use the 9/16” wrench to remove the bolts and

hold-down brackets.

Lift the front crossbar ends, as needed, for access.

b. Carefully roll the library back 1.25” (3cm) and

remove the front crossbar.

c. Use the adjustable wrench to loosen and raise the

two leveling legs (Figure 6).

4. Verify that all four leveling legs can clear the floor at

the bottom of the ramp and that the library is only

supported by the four caster wheels.

WARNING: Most of the weight of a library is located

in the rear. If the leveling legs are not raised high

enough, they can catch at the bottom of the ramps,

tipping over the library.

5. Carefully move the library down the ramps and onto

the floor.

CAUTION: Do not pull on the media drawer handles

when moving the library.

Before moving the library to its final operating position,

attach the doors.

1. Reattach the back door to the rear of the library.

2. Remove the two doors from the Door shipping box;

then, remove them from their plastic shipping bags.

NOTE: The square, straight end of the door is the top and the

curved end is the bottom.

3. Locate the bag of nylon washers taped inside one of

the doors.

The washers are used as bearings between the hinges.

4. Attach the left door (Figure 7).

a. Lift the top hinge pin just enough to retract the tip

into the left door’s hinge block.

b. Place one nylon washer onto the bottom hinge pin

that protrudes below the door hinge block.

It is held in place by the hinge pin’s ball retainer.

c. Position the door vertically with the bottom hinge

pin above the library hinge block hole and seat it.

d. Raise the door slightly, push down the top hinge.

pin slightly, and place a nylon washer onto it.

It is held in place by the hinge pin’s ball retainer.

Figure 7. Attaching the Front Doors

NEO-8106

Attaching the Doors

NEO-8091

Nylon Washers

Door

Left Door

Hinge

Block

Library Hinge Block

(between hinges)

Hinge Pin

Door Check

e. Lower the door so that the top hinge pin is above

the library hinge block hole and seat it.

5. Check the door to make sure it closes smoothly, yet is

held firmly.

6. If the door does not close as described in Step 5, adjust

it for alignment and operation:

a. Using the flat-blade offset screwdriver, unscrew the

door checks in both left library hinge blocks until

the door closes freely (Figure 7 on page 3).

b. Close the door and check that the top edge of the

door meets the front panel façade evenly.

•If the door is low, add washers to raise the door.

•If the door is high, remove the top washer.

CAUTION: The weight of the door should be

carried by at least one hinge with a nylon washer

(i.e., there must be at least one washer).

c. When the door height is correct, screw in the door

checks until the door closes smoothly, yet is held

firmly.

7. Repeat Steps 4–5 for the right door; if needed,

repeat Step 6.

Move the library into its final position and level it:

CAUTION: Do not pull on the media drawer handles

when moving the library.

1. Position the library at its operating location.

2. Run down all four leveling legs by hand until they

contact the floor.

3. Using the 10” adjustable wrench, turn each leg, one

after the other in equal increments, until you have

turned them at least one full turn.

NOTE: Be sure the library has been raised high enough so

none of the casters touch the floor.

4. Place the level, front to rear, on the top side edge of

the library (see Figure 8).

5. Note the position of the bubble. Raise both of the front

legs or both of the rear legs the same amount to

achieve a level front-to-rear reading.

6. Place the level across the top front edge of the library.

7. Note the position of the bubble. Raise both of the left

feet or both of the right feet the same amount to

achieve a level side-to-side reading.

8. Recheck the level from front-to-rear and from

side-to-side. Adjust as needed until the library is level.

Figure 8. Positioning the Level

You are now ready to connect the library to your network. Refer to the Overland NEO 8000 Library User Guide for

information required to complete this installation.

Leveling the Library

NEO-8112

What’s Next?

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Altri manuali per NEO 8000

Indice

Altri manuali Overland Storage Magazzinaggio

Overland Storage

Overland Storage NEO 2000e Manuale utente

Overland Storage

Overland Storage NEO 200S Manuale utente

Overland Storage

Overland Storage REO Series Manuale utente

Overland Storage

Overland Storage SnapServer Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage NEO 8000 Guida

Overland Storage

Overland Storage SnapSAN S2000 Manuale utente

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage SnapServer DX1 Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage ARCvault 12 Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage Ultamus Raid 1200 Manuale utente

Overland Storage

Overland Storage SnapServer DX1 Manuale utente

Overland Storage

Overland Storage ARCvault Series Manuale utente

Overland Storage

Overland Storage SnapScale X2 Node Manuale utente

Overland Storage

Overland Storage NEOxl 40 Manuale utente

Overland Storage

Overland Storage REO 9000 Manuale utente

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage NEO XL Series Manuale utente

Overland Storage

Overland Storage ULTAMUS RAID 4800 Manuale utente

Overland Storage

Overland Storage SnapSAN S1000 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente