Panasonic ZU-1870MA6T2 Manuale utente

Spec.No.: MES-DG60B038A

SPECIFICATIONS

FOR

MANUAL INSERTION

MAGNETIC CARD READER

Z U – 1 8 7 0 M A 6 T 2

MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.

MATSUSHITA INDUSTRIAL EQUIPMENT CO.,LTD.

CONTENTS

1. INTRODUCTION---------------------------------------------------------------- P-1

2. COMPOSITION------------------------------------------------------------------ P-1

3. SPECIFICATION----------------------------------------------------------------- P-1

4. TERMINAL NO. OF CONNECTOR--------------------------------------- P-3

5. INTERFACE REQUIREMENTS--------------------------------------------- P-3

6. NOTES FOR BETTER OPERATION------------------------------------- P-5

7. APPEARANCE--------------------------------------------------------------------P-6

8. CONNECTOR DIMENSION---------------------------------------------------P-7

9. MAGNETIC CARD SPECIFICATION--------------------------------------P-7

10. LIFE OF PARTS----------------------------------------------------------------P-8

11. MAINTENANCE METHOD---------------------------------------------------P-8

12. CAUTIONS ON THE USE---------------------------------------------------P-8

1. INTRODUCTION

This specification applies to the Panasonic magnetic card reader,

featuring small size, light weight and high performance.

2. COMPOSITION

The magnetic card reader is composed of the mechanical portion,

double circuits for reading.

1) Mechanical portion

The mechanical portion is mainly composed of the following parts.

1. Body (Color:Transparence)

2. Card entrance slot (Color: Black)

3. Magnetic head

4. Rubber seal

2) Circuit portion

1. Read amplifier circuit for 2 tracks

3. SPECIFICATION

3.1 CARD STANDARD

Refer to Magnetic Card Specification (9).

3.2 FUNCTION

(1) Read/Write : Read only

(2) Read timing : Ejection

(3) Compatibility : Cards and installation

(4) Installation of the transport : Horizontal direction

3.3 BASIC PERFORMANCE

(1) Performance

(2) Card operation speed : 10 cm/s to 100 cm/s

(3) Magnetic head Channel : 2

Channel width : 1.4 mm

(4) Insulation resistance : More than 10 MΩat DC 250 V

(Measured between P.C.B. ground terminal and frame)

(5) UL File No. : E140407

(6) Waterproof level : IPX4

3.4 ENVIRONMENT REQUIREMENTS

(1) Temperature range : -20 oC to 60 oC

(Operation)

(2) Temperature range : -30 oC to 70 oC

(Conservation)

(3) Humidity range : 10 % RH to 90 % RH

(Operation) (No condensation allowed)

(4) Humidity range : 10 % RH to 90 % RH

(Conservation) (No condensation allowed)

(5) Vibration : Vibration sweep 10 Hz to 50 Hz,

sweep 0.5 oct/min

X,Y,Z directions : 10 m/s

(6) Shock durability : 294 m/s2 (30 G)

ZU-1870MA6T2

ISO 7810,7811

Card standard

IS01 IS02

Track used Track 1st Track 2nd

Recording method FM FM

Recording

density 210 BPI 75 BPI

Recording

Capacity

79 characters

(7-bit code)

40 characters

(5-bit code)

3.5 PHYSICAL CHARACTERISTICS

(1) Dimension : (W) 90 mm x (D) 119.5 mm x (H) 46 mm

(2) Mass : Approx. 100 g

(3) Power supply : DC 5 V ± 0.5 V / Ripple(Less than 25 mA)

(4) Ripple : Within 50 mV

p-p

(5) Operating place : Indoor

3.6 ERROR RATE

(at indoor conditions by continuous running)

(1) Error : Less than 0.5 %

* Condition ··················In a clean office room.

In damp or dusty atmosphere, the life may be 1/3 to 1/5 of

the above figure.

4. TERMINAL NO. OF CONNECTOR

4.1 OUTPUT SIGNAL

Connector: 641216-7

5. INTERFACE REQUIREMENTS

5.1 OUTPUT VOLTAGE

Min(V) Max(V) Conditions

H level "0"

4.0 V

cc I

OH= -1.0 mA

L level "1"

- 0.4 I

OL= 4.0 mA

Connector

Pin No.

Signal

name

Connector

Pin No.

Signal

name

DC 5 V 5 /RCL2

/RDT1 6 /CLD

/RCL1 7 GND

/RDT2 - -

5.2 OUTPUT SIGNALS

The following paragraphs describe the requirements

and interface signals between the user terminal and

the Magnetic Card Reader shown in Figure 1.

The general timing sequence for entering data from

the Magnetic Card Reader to the user terminal is shown

in Figure 2.

/CLD

Magnetic /RCL1,2 User's

Card Reader /RDT1,2 Terminal

GND

DC 5V

Figure 1

(1) /CLD (CARD LOAD)

The /CLD line will be High when a Magnetic Card is inserted

in the end of Magnetic Card Reader.

The /CLD line will be Low at all other times.

(2) / RCL1,2 (READ CLOCK)

This is used to sample the data line by it's falling edges.

The time relationship of the clock with respect to the other

signals is shown in Figure 2.

User's Terminal starts to carry out sampling of the read data

by the falling edge of the signal.

In case of performing sampling other than the falling edge

sampling method

(such as detecting “L” of /RCL by means of polling)to read

/RDT, check /RCL width if it is appropriate.

(3) /RDT1,2 (READ DATA)

At the moment /RCL change from High to Low ;

/RDT is "1" when the /RDT line is Low, and

/RDT is "0" when the /RDT line is High.

5.3 TIMING CHART

Detail Chart

When the jitter of the magnetic head output is 0 % , the following

equation is satisfied.

T=T1=T2=T3, t1=t2

2.54 cm/inch 1

Note : T (s) = x

Recording density (BPI) Card speed (cm/s)

6. NOTES FOR BETTER OPERATION

(1) The card should be inserted in the specified direction.

(2) The card which conformed ISO standard should be used.

(3) The cards should not be dirty, scratched or deformed.

7. APPEARANCE

8. CONNECTOR DIMENSION

POST(641216-7 AMP)

9. MAGNETIC CARD SPECIFICATION

9.1 CARD SPECIFICATION

(1) Thickness : 0.76 mm (tolerance ± 0.08 mm)

(2) Transformation : 2 mm max.

(3) Impermeability rate : More than 2.0

(Measured by light permeance desitometer)

9.2 MAGNETIC CHARACTERISTICS

(1) Coercive force (Hc) : 2.4 x 10

4A/m (300 Öe ± 12%)

(2) Residual flux (¢r) : 1.25 x 10-8 Weber/cm

(1.25 ± 0.15 maxwell/cm)

(3) Squareness ratio (¢r/¢m) : More than 0.70

10. LIFE OF PARTS

Magnetic head : 500,000 passes

*Condition ·············· In a clean office room.

In damp or dusty atmosphere, the life may be

1/3 to 1/5 of the above figure.

11. MAINTENANCE METHOD

When replacing parts, exchange the card reader unit.

12. CAUTIONS ON THE USE

Please be noted that we do not guarantee proper performance of the

card reader if it is used other than the indicated specification range.

12.1 At the installation

(1) Do not drop or bump anything against a card reader.

Otherwise, failure may be the result.

(2) Do not touch the P.C.B. with bear hands.

(3) Be sure to install on a flat surface so as to prevent any force to be

applied to the card reader at the installation.

(4) Installation of a card guide plate at the both (front and back) sides of

the card running part may reinforce stability.

(5) The card reader should avoid installation of the following environment.

· Watery, humid or dusty place.

· Near machines which generate magnetic field or inducted noise.

(printer,LED display, CRT etc.)

· Place which gets direct sunlight.

Indice

Altri manuali Panasonic Lettore di schede

Panasonic

Panasonic AJ-PCD35 Manuale utente

Panasonic

Panasonic FZ-VNF551 Series Manuale utente

Panasonic

Panasonic AGHPG10P - MEMORY CARD PORTABLE RECORDER Manuale utente

Panasonic

Panasonic AJ-PCD10P Manuale utente

Panasonic

Panasonic AJ-PCD10E Manuale utente

Panasonic

Panasonic UD-7900N14EU Manuale utente

Panasonic

Panasonic AJ-PCD20EJ Manuale utente

Panasonic

Panasonic CF-VCRU11U Manuale utente

Panasonic

Panasonic AJ-PCD20MC Manuale utente

Panasonic

Panasonic JT-R210CR-50 Manuale utente

Panasonic

Panasonic FZ-VSC552 Series Manuale utente

Panasonic

Panasonic FZ-VSC402 Series Manuale utente

Panasonic

Panasonic FZ-VSDR55 Series Manuale utente

Panasonic

Panasonic FZ-VDM551 Series Manuale utente

Panasonic

Panasonic ZU-9PS Series Manuale utente

Panasonic

Panasonic FZ-VGT551 Series Manuale utente

Panasonic

Panasonic LP-ABR10 Series Manuale elenco delle parti

Panasonic

Panasonic LP-ABR11 Manuale di istruzioni

Panasonic

Panasonic FZ-VNF401 Series Manuale utente

Panasonic

Panasonic AJ-PCD35 Manuale utente

Panasonic

Panasonic BN-SDCMAB Manuale utente

Panasonic

Panasonic AJ-PCD30PJ Manuale utente

Panasonic

Panasonic au-xpd1 Manuale utente

Panasonic

Panasonic AJHPM110E - MEMORY CARD PORTABLE... Manuale utente

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente