Panasonic AJ-YAC77P Manuale utente

SDTI Interface Board

AJ-

F0400T50 @

VQT8801

Check that the following items have been packed together with the board.

Note that as the SDTI board is compatible with both NTSC and PAL, both NTSC and PAL ROMs

have also been included with the board.

CONTENTS PIECES CONTENTS PIECES

SDTI board 1 TRV_IF board (VEP83392B) 1

ROM for NTSC (VSI3385) 1 Coaxial cable (black) 1

ROM for NTSC (VSI3386) 1 Coaxial cable (red) 1

ROM for NTSC (VSI3387) 1 Coaxial cable (yellow) 1

ROM for PAL (VSI3388) 1 SDTI terminal board 1

ROM for PAL (VSI3389) 1 Blank panel 1

ROM for PAL (VSI3390) 1 Installation guide (what you are reading) 1

Introduction

Contents

Connector section

This product is an SDTI interface board designed for use in the AJ-DE77, AJ-DE77H and AJ-

DE77D models using Ver 3.0 or later of the Quick Cutter application.

Installation of this product in the AJ-DE77, AJ-DE77H or AJ-DE77D enables digital data using the

SDTI format*1(digital data compression interface) to be input and output.

1 SDTI dedicated serial digital input connector (BNC x 1)

2 SDTI dedicated serial digital output connector (BNC x 1)

SDTI

OUT

11Used exclusively for SDTI input signals

22Used exclusively for SDTI output signals

*1: SDTI (serial data transport interface) complies with the SMPTE 305M standard.

The data stream format complies with the SMPTE 321M standard.

Introduction .......................................................................................................... 2

Before installation................................................................................................ 2

Connector section................................................................................................ 2

Installation ............................................................................................................ 3

Precautions for SDTI use..................................................................................... 7

Specifications....................................................................................................... 7

CAUTION :

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER INSTALLATION OF THIS

BOARD TO QUALIFIED SERVICE PERSONNEL.

Before installation

Check that the power of the AJ-DE77, AJ-DE77H or AJ-DE77D (hereafter referred to as the “Quick

Cutter” ) is OFF.

Remove the four screws securing the top panel of the

Quick Cutter, then remove the panel.

Installation

While referring to the figure on the right, first

disassemble the accessory terminal board, and then

use two screws to secure the board to the right side

of the jack panel and two screws to secure the blank

panel on the left side.

(In the case of the AJ-DE77D, the blank panel is not

attached because the SDI terminal board is already in

place on the left side.)

After installation, the panels should appear as shown

in the figure below.

Connect the red coaxial cable provided with the

board to the SDTI terminal board OUT and the black

coaxial cable to the SDTI terminal board IN.

SDI

OUT

AJ-DE77 AJ-DE77D

AJ-DE77H

Jack panel

(AJ-DE77 or AJ-DE77H)

Screws (x6 for

each side panel)

Screws (x7)

Screws (x4)

Blank panel

Remove the 12 screws securing the two side panels

of the Quick Cutter, then remove the panels.

Remove the seven screws securing the jack panel,

then remove the jack panel from the unit.

(It cannot be completely detached because its cable

remains connected.)

Remove the four screws securing the blank panel,

then remove the blank panel from the unit. (Remove

the two screws in the case of the AJ-DE77D.)

Enlarged view

Before installation

SDI

OUT

SDTI

OUT

SDTI

OUT

AJ-DE77 AJ-DE77D

AJ-DE77H

Blank panel

After installation

After threading the coaxial cables connected to the terminal board

through points 1and 2as shown at right, replace the jack panel

on the main unit.

(AJ-DE77 only)

Remove the two screws and two hexagonal bolts of the AV

interface connector at the bottom rear of the Quick Cutter and

remove the TRV interface board together with its metal clamp.

Installation

(AJ-DE77 only)

Remove the four screws securing the TRV interface board and metal clamp,

and replace the board with the accessory TRV interface board, then use the

four screws to secure the metal clamp.

(AJ-DE77 only)

Use two screws and two bolts to secure the metal clamp, which was

attached to the TRV interface board, to the Quick Cutter unit.

Screws (x2) Hexagonal bolts (x2)

Screws (x2)

Hexagonal bolts (x2)

Screws (x4)

Enlarged view

11Pass the cable through the oval-shaped hole.

22Pull the cable out from the position shown.

AV I/F

NTSC

PAL

Black

Red

Yellow

S_IN1

S_OUT2

REF_IN

Jumper setting diagram Coaxial cable connection diagram

After setting NTSC or PAL for the P4 pin of the accessory SDTI board as shown in the jumper setting

diagram, refer to the coaxial cable connection diagram and connect the coaxial cables. The connections

with the board should be made in the following order:

1Connect the coaxial cable (black) which was connected in step 7 to the S_IN1 connector on the SDTI

card provided with the unit.

2 Connect the coaxial cable (red) which was connected in step 7 to the S_OUT2 connector on the SDTI

board.

3 Connect the coaxial cable (yellow) provided with the unit to the REF_IN connector on the SDTI board.

Remove the 20-pin remote cable shown at right

from the Remote I/O board connector followed by

the 3 screws, then remove the board metal clamp

from the Quick Cutter unit.

(For AJ-DE77H and AJ-DE77D, also remove the 2

screws and the fan as shown in the diagram at

right. It is not necessary to remove the fan’s power

cable.)

Installation

Remove the cable and screw shown in the diagram at

right, then remove the X4PCI board from the slot.

Insert the accessory SDTI board into the slot which had

accommodated the X4PCI board, secure it using the

screw, and connect the cable that was disconnected

from the X4PCI board to the connector of the SDTI

board.

Connect one end of the coaxial cable (yellow), which was

connected in step 11, to the J7 connector on the TRV

interface board.

Replace the board metal clamp (and the fan for AJ-DE77H and AJ-DE77D) removed in step 12 and

secure it with the 3 screws.

Connect the 20-pin remote cable removed in step 12 to the Remote I/O board connector.

Yellow

Screws

(x3)

Screw

Enlarged view

Cable

Screws (x2) for AJ-DE77H or

AJ-DE77D only 20-pin remote cableBoard metal clampFan

Replace the two ROMs (IC2 and IC702) from the VTR units F2 board with the ROMs provided with the

board.

Refer to the figure of the circuit board below to ensure that the ROMs are installed in the correct

direction.

Replace the ROM (IC235) from the VTR unit's F1 board with the ROM provided with the board.

Refer to the figure of the circuit board below to ensure that the ROM is installed in the correct direction.

Remove the 4 screws shown in the diagram at

right and the right metal fitting grip of the

Quick Cutter unit, then remove the F1 and F2

boards of the VTR unit.

Return the F1 and F2 boards removed in step 16 to their original positions, and use the four screws to

secure the right metal fitting grip which was removed in step 16 to the Quick Cutter unit. Secure the side

panels and the top panel using the screws by performing steps 2 and 3 in their reverse order.

Installation

Accessory ROM

VSI3387

VSI3390

Reference

IC235

NTSC

PAL

Screws (x4)

F1 board

F2 board

IC702 IC2

IC235

Align pin 1, and insert the ROMs

while ensuring that their pins are

not bent in the process.

Align pin 1, and insert the ROM

while ensuring that its pins are

not bent in the process.

Reference

IC2

IC702

IC2

IC702

Accessory ROM

VSI3385

VSI3386

VSI3388

VSI3389

NTSC

PAL

Precautions for SDTI use

Specifications

≥Before handling the interface board and its ROMs, be absolutely sure to attach a grounding strap.

≥Recording operations cannot be performed unless the SDTI input signals are DVCPRO (25

Mbps) format 4x or 1x transfer signals.

≥Recording operations can be performed only when the video, audio and time code data of the

SDTI signals are all regular data in compliance with the DVCPRO (25 Mbps) format.

≥Before use, supply the external reference signal to the reference input connector on the Quick

Cutter unit.

≥When inserting or ejecting a tape from the Quick Cutter equipped VTR, there will be some noise

from the SDTI analog monitor output screen.

≥When using this interface board, be absolutely sure to read the instructions for Quick Cutter

application Ver 3.0 as well.

≥This interface board can be operated with the Quick Cutter Ver 3.0 or later.

However, since it may be necessary to update the version of the software program for the VTR

which contains Quick Cutter, consult your dealer.

GENERAL

Weight Board : 185 g

Terminal board : 32 g

Dimensions Board : 255(W) x 140(H) x 22(D) mm

Terminal board : 28(W) x 88(H) mm

VIDEO/AUDIO IN

Serial digital input : BNC x 1

IN : SDTI input

SDTI : Complies with SMPTE 305M standard

VIDEO/AUDIO OUT

Serial digital output : BNC x 1

OUT : SDTI output

SDTI : Complies with SMPTE 305M standard

PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY

DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA

Executive Office:

3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500

EASTERN ZONE:

One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621

Mid-Atlantic/New England:

One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621

Southeast Region:

1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835

Central Region:

1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200

WESTERN ZONE:

3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500

Dallas Region:

6226 Abington Way, Houston, TX 77008 (713) 802-2726

No. CA/Northwest Region:

5870 Stoneridge, #3, Pleasanton, CA 94588 (925) 416-5108

Government Marketing Department:

52 West Gude Drive, Rockville, MD 20850 (301) 738-3840

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010

Panasonic Sales Company

Division of Matsushita Electric of Puerto Rico Inc.

San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300

Indice

Altri manuali Panasonic Hardware per computer

Panasonic

Panasonic 2SA2161G Manuale utente

Panasonic

Panasonic 2SC1473 Manuale utente

Panasonic

Panasonic AV-HS04M4 Manuale utente

Panasonic

Panasonic CF-BAW1024U Manuale utente

Panasonic

Panasonic 2SC3934 Manuale utente

Panasonic

Panasonic 2SC2295 Manuale utente

Panasonic

Panasonic MICROCOMPUTER MN103S Manuale utente

Panasonic

Panasonic 2SC2406 Manuale utente

Panasonic

Panasonic PAW-FC Manuale

Panasonic

Panasonic ET-MDNDP10C Manuale utente

Panasonic

Panasonic AW-360B10 Manuale utente

Panasonic

Panasonic ET-MDNHM10 Manuale utente

Panasonic

Panasonic 2SA2174G Manuale utente

Panasonic

Panasonic 2SB1320A Manuale utente

Panasonic

Panasonic 2SA1748 Manuale utente

Panasonic

Panasonic KX-TDA0170 Manuale utente

Panasonic

Panasonic WZ-TDADP Manuale utente

Panasonic

Panasonic 2SB1321A Manuale utente

Panasonic

Panasonic TY-42TM6G Manuale utente

Panasonic

Panasonic CF-BAL1024U Manuale utente

Panasonic

Panasonic FP2 Series Manuale utente

Panasonic

Panasonic TY-FB11DD - Monitor Terminal Expansion Board Manuale utente

Panasonic

Panasonic WZ-TDDA Manuale utente

Panasonic

Panasonic TY-42TM6B - Monitor Terminal Expansion Board Guida utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente