Panasonic EY6105-X8 Manuale utente
1 SCHEMATIC DIAGRAM 2
2 WIRING CONNECTION DIAGRAM 2
3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS 3
©2004 Matsushita Electric Works Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
EY6105-X8
4 TROUBLESHOOTING GUIDE 7
5 EXPLODED VIEW 8
6 REPLACEMENT PARTS LIST 9
Cordless Drill & Driver
SPECIFICATIONS
CONTENTS
Page Page
ORDER NO.PTD0411X48C8
1 SCHEMATIC DIAGRAM
2 WIRING CONNECTION DIAGRAM
2
EY6105-X8
■HOW TO DISASSEMBLE KEYLESS CHUCK.
3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS
Ref. No. 1A Procedure 1A Removal of the Keyless Drill Chuck.
Fig.1
Fig.2
Fig.3
1. Set the clutch handle to position and select "LOW"
position.
2. Turn the lock collar counterclockwise direction to open the chuck
jaws.
3. Use a screwdriver to turn the chuck fastening screw inside the
chuck clockwise direction of the arrow, and remove the screw.
(See Fig.1)
NOTE :
If the chuck fastening screw will not come loose, insert the
allen wrench into the chuck and lightly tap in the clockwise
direction with a hammer to tighten the chuck, and then loosen
the chuck fastening screw. (See Fig.2)
4. Insert the allen wrench into the chuck, and turn counterclockwise
direction in the arrow with holding the unit by the vise to remove
the chuck. (See Fig.3)
3
EY6105-X8
■HOW TO DISASSEMBLE MAIN UNIT.
Ref. No. 2A Procedure 2A Removal of the Housing.
1. Remove 8 housing screws.
(See or Fig.4)
Fig.4
Ref. No. 2B Procedure 2A →
→→
→2B Removal or attachment of the Motor.
Fig.5
(Removal)
1. Take out the motor with the gear box block from housing.
2. Separate the motor from the gear box block by twisting the motor
to unlock tabs.
(Attachment)
3. Motor mounting base and the positioning rib of gear case should
be set. (See Fig.5)
4
EY6105-X8
Ref. No. 2C Procedure 2A →
→→
→2B →
→→
→2C Removal or attachment of the Gear Box Block.
Fig.6
Fig.7
(Removal)
1. Turn the thrust plate to remove.
2. The internal parts of gear box block can be removed one after
another. (See Fig.6)
(Attachment)
1. Start from inserting 6 pins into the driving block as shown in the
Fig.7.
2. Assemble the other parts in reverse order as shown in the
Fig.6.
NOTE :
Carrier, Ring Gear, and Ring Gear A have their own correct
directions for proper reassembly.
3. Insert 2 pieces of steel ball into each 6 holes of gear case.
4. Set clutch plate and clutch spring.
NOTE :
Clutch plate has its own correct direction for proper
reassembly.
5
EY6105-X8
Ref.No.2D Procedure 2A →
→→
→2B →
→→
→2C →
→→
→2D Assembly of the Adjusting Screw and the Clutch
Handle.
Fig.8
1. Align the mark of adjusting screw with the projection (A) of
driving block.
2. Turn the adjusting screw into the driving block about one
rotation for clockwise direction.
3. Align the hollow (A) of adjusting screw with the projection (A) of
driving block.
4. Set the clutch handle with position 1 on top. (Aligh the position 1
of clutch handle with the projection (A) of driving block.)
5. Insert the clutch handle with adjusting the tabs of adjusting
screw to the groove of inside clutch handle.
6
EY6105-X8
(Refer to WIRING CONNECTION DIAGRAM)
4 TROUBLESHOOTING GUIDE
< TROUBLE > < CHECK > < REMEDY >
Does not operate. <CHECK BATTERY PACK.> NO Replace battery pack.
→If no less than 12V DC is available across the (+) and (-) terminals, →
the battery pack is OK.
NOTE: The battery pack is sold separately as an optional accessory.
See the nearest sales dealer for details. The battery pack has a
limited life.
The pack should be replaced if;
-after being charged for the rated charging time the battery voltage
is less than 12V DC or the usable time is extremely short.
-the battery leaks. Check battery for leaks and terminals for
corrosion.
↓OK
<CHECK TERMINAL CONNECTIONS BETWEEN MAIN UNIT NO Repair contacts.
AND BATTERY PACK.> →
Check for proper terminal contacts.
↓OK
<CHECK SWITCH BLOCK.> NO Contacts in switch block
(See .WIRING CONNECTION DIAGRAM.) →are defective.
Check continuity between following terminals. Replace switch & FET
*Inspection of the forward / reverse selection switch. block.
When switch handle is depressed all the way:
-There should be 0Ωbetween (A) - (D) , and between (B) - (C) ;
when switch lever is set to forward side.
-There should be 0Ωbetween (A) - (D) , and between (B) - (C) ;
when switch lever is set to foward side.
*Inspection of the brake.
When switch handle is not depressed:
-There should be 0Ωbetween (A) - (B) .
↓OK
<CHECK MOTOR.> NO Replace motor.
It is OK if motor rotates 22,200 ± 2,800rpm with no-load operation and no-load →
current is 2.6A or less when connecting 12V DC between white (+) and black
(-) lead wires.
NOTE: It is OK if motor rotates slowly when connecting 3V DC between
white and black lead wires.
Does not speed-
control or does not
brake.
<CHECK FET.> NO Repair the contact or
replace switch & FET
block.
→Even if FET block is defective, it can not be replaced individually. Replace
whole switch block.
→
7
EY6105-X8
5 EXPLODED VIEW
8
EY6105-X8
6 REPLACEMENT PARTS LIST
NOTE:
*B=only available as set
*C=available individually
Ref.No. Part No. Part Name & Descriptions Remarks Per Unit
1WEY6105K3079 HOUSING AB SET for EUROPE 1
1WEY6105K3070 HOUSING AB SET for OCEANIA 1
2WEYT103L6807 CHUCK FASTENING SCREW 1
3WEY6105K7918 KEYLESS CHUCK 1
4WEY6406Y3228 CLUTCH HANDLE 1
5WEYT107L0457 CLICK SPRING A 1
6WEYT107L0637 ADJUSTING SCREW 1
7WEYT107L0167 CLUTCH SPRING 1
8WEY6406L0578 CLUTCH PLATE 1
9WEY7000L6967 STEEL BALL *B 5 (12pcs/PK) 12
10 WEYT107L1067 DRIVING BLOCK 1
11 WEY6481L0357 THRUST PIN SET *C 2.5*33.6s 2
12 WEY6105L1468 RING GEAR 1
13 WEY6105L1368 PLANET GEAR B *B (3pcs/PK) 3
14 WEY6200B0857 THRUST PLATE 1
15 WEYT104L1357 CARRIER B 1
16 WEY6481L1458 RING GEAR A 1
17 WEYT107L1357 PLANET GEAR *B (3pcs/PK) 3
18 WEYT104L1107 CARRIER A 1
19 WEY6101L1477 RING GEAR B 1
20 WEY6105L1378 PLANET GEAR A *B (3pcs/PK) 3
21 WEY6481L0887 THRUST PLATE 1
22 WEY6230L6027 SCREW *C K3-6 2
23 WEYT104L0027 MOTOR MOUNTING PLATE 1
24 WEY6105L1008 DC MOTOR 1
25 WEYT107Y3237 H/L CHANGE HANDLE 1
26 WEYT107Y2007 SWITCH 1
27 WEY6230L6037 SCREW *C K3*5 2
28 WEY6481L0207 DUST PREVENTIVE PLATE 1
29 WEYT602Y3247 F/R SELECTOR HANDLE 1
30 WEYT107L2567 HEAT SINK 1
31 WEY6403L6007 TAPPING SCREW 2.6*5 1
32 WEY6105K9038 TORX TAPPING SCREW *C K3*18 8
33 WEY6105L1458 GEAR BOX BLOCK 1
-WEY6405K7018 TOOL CASE 1
-WEY6105K8109 OPERATING INSTRUCTIONS 1
**Battery Pack is available as an optional accessory. See the nearest sales dealer for details.
***For replacement parts of charger, see the charger service manual. Charger complete set is available as an optional accessory.
See the nearest sales dealer for details.
9
EY6105-X8
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Panasonic Trapano avvitatore a batteria
Panasonic
Panasonic EYFEA1N Manuale utente
Panasonic
Panasonic EY6535-U1 Manuale utente
Panasonic
Panasonic EY6450-X8 Manuale utente
Panasonic
Panasonic EY7441 Manuale utente
Panasonic
Panasonic EY6405-U1 Manuale utente
Panasonic
Panasonic EY7442 Manuale utente
Panasonic
Panasonic EY7410-U1 Manuale utente
Panasonic
Panasonic EY6405FQKW Manuale utente
Panasonic
Panasonic EY6101 - 12.0V DRILL & DRIVER Manuale utente
Panasonic
Panasonic EY6409NQKW Manuale utente
Panasonic
Panasonic EY 6220 Manuale utente
Panasonic
Panasonic EY6780 Manuale utente
Panasonic
Panasonic EY7441 Manuale utente
Panasonic
Panasonic EY6408 Manuale utente
Panasonic
Panasonic EY7442 Manuale utente
Panasonic
Panasonic EY7440-U1 Manuale utente
Panasonic
Panasonic EY74A2 Manuale utente
Panasonic
Panasonic EY7410-X8 Manuale utente
Panasonic
Panasonic EY6901 Manuale utente
