Panasonic RG-C811A Manuale utente

Model No.

READ AND SAVE THESE INSTRUCTIONS

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting

to install, operate or service the Panasonic product. Please

carefully read the “GENERAL SAFETY INFORMATION”.

Failure to comply with instructions could result in personal

injury or property damage. Please explain to users how to

operate and maintain the product after installation and this

manual should be presented to users. Please retain this

manual for future references.

RG-C811A, RG-C811HA

Ventilating Fan

The following symbol word panels are used to classify and describe the level of hazard, injury, and property damage

caused when the denotation is disregarded and improper use is performed.

To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always

observe the following safety precautions.

WARNING

CAUTION

Denotes a potential hazard that could result in serious injury or death.

Denotes a hazard that could result in minor injury.

Denotes a hazard that could result in property damage.

The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users not to disassemble the equipment.

This symbol is used to alert users to make sure of grounding when using the equipment with the grounding

terminal.

This symbol is used to alert users to a specific operating procedure that must be followed in order to

operate this unit safely.

This symbol is used to alert users to a specific operating procedure that must not be performed.

INSTALLATION INSTRUCTIONS

See page 12 for “Panasonic Warranty Sheet”.

GENERAL SAFETY INFORMATION

C8 1 1 A1 4 2 0 A

WARNING

To reduce the risk of fire, electric shock or injury to persons, observe the following:

Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the

manufacturer.

burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and

safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society of Heating, Refrigerating and Air-Conditioning Engineers

(ASHRAE) and the local code

authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means

to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel

Ducted exhaust fans must always be vented to the outdoors.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and

connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

These models are UL listed for tub and shower enclosures.

If this product is no longer to be used, it must be removed from the ceiling to prevent it from falling.

Do not install with a method which is not approved in the instructions.

This product must be properly grounded.

Do not use this fan with any solid-state speed control device. Solid state controls may cause harmonic

distortion which can cause a humming noise in the motor.

Do not disassemble the unit for reconstruction. It may cause fire or electric shock.

The ceiling joist must be able to withstand a static load of at least five times the weight of the product.

GENERAL SAFETY INFORMATION (CONTINUED)

Make sure that the electric service supply voltage is AC 120 V 60 Hz.

Do not install this ventilating fan in a location where the interior room temperature may exceed 104 °F (40 °C).

Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the

Occupational Safety and Health Administration (OSHA).

CAUTION

Always disconnect the power source before working on or near the fan, motor or junction box.

Protect the supply wiring from sharp edges, oil, grease, hot surfaces,

chemicals or other objects.

Do not kink the supply wiring.

Not for use in cooking area. (Fig. A)

The special-purpose or dedicated parts, such as

mounting fixtures, must be used if such parts are

provided.

For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

Floor

45°

Cooking

equipment

Fig. A

(Cooking area)

Do not install above or

inside this area

Provide make up air for proper ventilation.

Do not connect multiple units in parallel. If two or more units are connected to one switch in parallel, the units

may not function.

Do not install the unit where ducts are configured as shown in below:

Bend close to duct adaptorSqueezed ductSuccessive bending

Excessive bending

Adaptor

DESCRIPTION

These products use a sirocco fan driven by a DC motor powered by an integral transformer. The motor is designed to

have long operating life, high dynamic response, higher speed ranges and energy savings. The grille covering the fan

body is a spring-attached, quick removal type. A damper for preventing air counter flow is provided. The blower uses

a high-capacity sirocco fan developed to reduce the noise level.

These products are listed by UL under UL file No. E78414.

(RG-C811HA only)

This Panasonic ventilating fan model is equipped with a humidity sensor that turns on automatically when humidity

increases rapidly, or when humidity rises above a 30% - 80% relative humidity set-point. It is user-adjustable to

operate 0.5 ~ 60minutes after the sensors are no longer detected.

GENERAL SAFETY INFORMATION (CONTINUED)

Unpack and carefully remove the unit from carton. Refer to the Supplied Accessories list to verify that all parts are

present.

Part name Appearance Quality

Grille

Flex-Z Fast ™

bracket (with 4

tapping screws

- ST4.2X20)

Part name Appearance Quality

Installation

instructions/

Warranty

sheet

Self-drilling

screw

Part name Part nameNo. No.

Blade

Grille

Junction box

Adaptor

PCB box

Pick-A-Flow™ switch

Fan body

Damper

Flex-Z Fast™ bracket

Unit: inches (mm)

RG-C811HA

RG-C811A

UNPACKING

DIMENSIONS

SUPPLIED ACCESORIES

12 (304)

10 1/4 (260)

3 7/8 (100)

5 7/8 (151)

7 1/2 (190)

13 (330)

13 1/4 - 15 1/2 (336-394)

16 1/2 - 18 3/4 (419-480)

21 1/4 - 23 1/2 (540-597)

10 5/8 (270)

3 3/8

(86)

7/8 (23.5)

1 1/2 (37)

4 1/2 (114)

13 (330)

10 1/4 (261) 3 7/8

(100)

12 (304)

10 1/4 (260)

3 7/8 (100)

5 7/8 (151)

7 1/2 (190)

13 (330)

13 1/4 - 15 1/2 (336-394)

16 1/2 - 18 3/4 (419-480)

21 1/4 - 23 1/2 (540-597)

10 5/8 (270)

3 3/8

(86)

7/8 (23.5)

1 1/2 (37)

4 1/2 (114)

RG-C811HA

RG-C811A

RG-C811HA

DIMENSIONS (CONTINUED)

WIRING DIAGRAM

SELECTOR INDICATION (RG-C811HA only)

AC 120 V 60 Hz

(Power supply)

Fan body

Main control circuit

Motor Main control

circuit

(Ground wire)

Green

Junction box

Neutral

White

Black Live (Fan)

AC 120 V 60 Hz

(Power supply)

Junction box Neutral

White

Black Live (Fan)

(Ground wire)

Green

Motor

Fan body

Main control circuit

Main control

circuit Humidity sensor

Selector

TimerHumidity

setting

Humidity

preset selector Timer

preset selector

Selector indications on

blower unit

Factory setting is around 50%.

Timer preset selector positions

13 (330)

10 1/4 (261) 3 7/8

(100)

Part name Part nameNo. No.

Blade

Grille

Junction box

Adaptor

PCB box

Pick-A-Flow™ switch

Fan body

Damper

Flex-Z Fast™ bracket

Selector

Humidity sensor

Duct length, elbows and other factors increase static pressure which can hinder the performance of most ventilation

fans. This fan utilizes Smart Flow™ microchip technology that monitors the static pressure in the system and speeds

up or slows down the rpm of the fan depending upon the amount of resistance within the ducts. This feature allows

the fan to perform as rated and avoid potential installation issues.

These products are built using DC motor technology. The DC motor is 30% ~ 70% more energy

efficient than the minimum ENERGY STAR requirements.

Pick-A-Flow™ Feature:

This product comes with Pick-A-Flow™ speed

options. The Pick-A-Flow™ switch on the face of the product allows the

option to choose 80 or 110 CFM.

This product can run continuously or intermittently, depending upon the

needs of the owner.

Pick-A-Flow™

switch

RG-C811A

RG-C811HA 80 CFM

80 110

110

Air volume (CFM) Factory setting

80 CFM

CFM

130 150

0811 MODEL

80 110

1315 MODEL

Tape

Adaptor Damper

WARNING

Disconnect power supply before

installing the unit.

Please wear gloves to protect hands

during the installation.

Remove the tape placed on the damper and

adaptor before installation. Failure to do so

will cause the product to work inefficiently and

create a loud noise.

OPERATION (RG-C811HA only)

INSTALLATION (RETROFIT)

FEATURES

Power

switch

Conden-

sation

sensor

Product

ON OFF

Stop Run

Environment humidity

Humidity trigger setting

about 5 %RH

Delay

operation

The product will continue to run for about

20 minutes after the sensor detects that

the humidity is ~5 % RH lower than the

humidity setting before stopping.

Stop

Note:

1. The power switch should be left on at all times.

2. The product will also run when the humidity rises rapidly but does not reach the humidity trigger setting, and then stop after

the time delay.

3. The activation humidity settings on the dial are continuous from 30 %RH ~ 80 %RH.

4. The humidity detected by the sensor may differ from the value on your hygrometer.

5. The product may cycle on and off if the humidity is constantly near the trigger point. This can be addressed by raising

the humidity trigger setting on the dial.

6. The fan will run for 20 minutes when power switch is first turned on, regardless of the humidity sensor settings. After 20

minutes, the fan will return to sensor mode.

Remove existing fan Joist

Unit: inches (mm)

Conduit Circular duct

Ceiling (already existed)

1Remove the existing fan and cut the ceiling opening

according to the required dimensions.

1Insert Flex-Z Fast™ bracket into the opening and

extend.

Align and install bracket to joist by using

2-preinstalled tapping screws.

Joist

2 Tapping

screws

(ST4.2X20)

Extend

Extend bracket to the other joist.

Install bracket to joist by using 2-preinstalled tapping

screws.

Flex-Z Fast™ bracket position can be adjusted from 16" to 24" (406mm to 610mm) between joists.

Install Flex-Z Fast™ bracket

Joist

2 Tapping screws

(ST4.2X20)

Flex-Z Fast™ bracket

Align

Joist

Flex-Z Fast bracket

™

Joist

Align the edge of Flex-Z Fast™

with the edge of the ceiling

opening on the side where the

adapter will be installed.

Drywall

Flex-Z Fast™ bracket

Joist

Drywall

Joist

INSTALLATION (RETROFIT) (CONTINUED)

Remove adaptor

from fan body

Disconnect plug connector from

the receptacle and remove adaptor

from fan body by removing the

machine screw (M4X8) before

installation.

Machine screw

(M4X8)

Fan body

Adaptor

Plug connector

Receptacle

Refer to WIRING DIAGRAM (Page 5). Follow all the local electrical safety codes as well as the National Electrical

Code (NEC). Use UL approved wire nuts to connect fan wires. After connecting wires, replace junction box cover.

Install and secure fan body

2 self-drilling

screws

Plug connector

Receptacle

Insert fan body and slide into adaptor assembly until the flange overlaps the Flex-Z Fast™ bracket.

Secure the fan body to Flex-Z Fast™ bracket by using 2 self-drilling screws.

Plug connector into receptacle and secure fan body to adaptor by using machine screw (M4X8).

Please take care when installing the machine screw (Step 5) to avoid cross threading and to ensure that the

screw does not strip or come in contact with Flex-Z Fast™ bracket.

Insert circular exhaust duct

Remove screw from junction box cover to remove the knock-out hole and secure conduit or stress relief to junction

box knock-out hole.

Install the circular exhaust duct and secure it with clamps or ties and seal it with mastic or approved foil tape. A 4

inch circular duct is needed to connect to the relevant part of the adaptor.

Install the adaptor to Flex-Z Fast™ bracket by using 2 self-drilling screws.

Machine screw

(M4X8)

INSTALLATION (RETROFIT) (CONTINUED)

Earth ground

Conduit

Junction

box

Neutral

Live

AC 120 V

60 Hz

LINE IN

Switch box

Wire nuts

GREEN

BLACK

WHITE

2 Self-drilling screws

Mastic or

approved

foil tape

Circular exhaust

duct

Junction box

cover

Knock-out

hole

Conduit

2 Self-drilling screws

Fan body

Joist

Flex-Z Fast™

bracket

Remove adaptor

from fan body

Disconnect plug connector from

the receptacle and remove adaptor

from fan body by removing the

machine screw (M4X8) before

installation.

Machine screw

(M4X8)

Fan body

Adaptor

Sealing

Adjust Pick-A-Flow™ switch. (Refer to explanation under

FEATURES). (Page 6)

Once fan body is mounted and secure, fill gap between flange

and ceiling with caulk or other sealant to prevent air leakage.

Joist

Tape

Adaptor Damper

WARNING

Disconnect power supply before

installing the unit.

Please wear gloves to protect hands

during the installation.

Remove the tape placed on the damper and

adaptor before installation. Failure to do so

will cause the product to work inefficiently and

create a loud noise.

Install Flex-Z Fast™ bracket

Flex-Z Fast™ bracket position can be adjusted from 16" to 24" (406mm to 610mm) between joists.

Unit: inches (mm)

Joist

Bend down 4 tabs

2 Tapping screws

(ST4.2X20)

Flex-Z Fast™ bracket

Align

2Align and install bracket to joist by using

2-preinstalled tapping screws.

Bend down 4 tabs and align bracket to the joist.

Plug connector

Receptacle

INSTALLATION (RETROFIT) (CONTINUED)

INSTALLATION (NEW CONSTRUCTION)

Install grille Mounting spring

Grille Gloves

Drywall

Insert the mounting springs into the slot as

shown to mount grille to fan body.

Disconnect power source before working on unit.

Routine maintenance must be done every year.

Please wear gloves during the cleaning work.

Never use gasoline, benzene, thinner or any other

such chemicals for cleaning the ventilating fan.

Do not immerse motor in water when cleaing.

Do not soak resin parts in water over 140°F (60°C).

Do not use cleaning sprays, solvents, or water on

or near the sensor.

Follow steps from “RETROFIT” Installation

1Follow the steps 4 to 7 on “INSTALLATION (RETROFIT)”.

Remove grille

Gloves Slot

Grille

Mounting spring

1Remove grille by pulling down one mounting spring

then pull the other.

Extend

Joist

2 Tapping screws

(ST4.2X20)

Extend bracket to the other joist.

Install bracket to joist by using 2-preinstalled

tapping screws.

MAINTENANCE (CLEANING)

INSTALLATION (NEW CONSTRUCTION) (CONTINUED)

Altri manuali per RG-C811A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Panasonic Fan

Panasonic

Panasonic F-60SVN Manuale utente

Panasonic

Panasonic WhisperLite FV-05VQ5 Manuale utente

Panasonic

Panasonic FV-10VEC2 Manuale utente

Panasonic

Panasonic Whisper Green-Lite FV-08VKML2 Manuale utente

Panasonic

Panasonic Whisper Value-Lite FV-10VSL2 Manuale utente

Panasonic

Panasonic WhisperGreen FV-08VKM3 Manuale utente

Panasonic

Panasonic FV-08VRE1 Manuale utente

Panasonic

Panasonic FV-08VSL3 Manuale utente

Panasonic

Panasonic FY-150ZDY8 Manuale utente

Panasonic

Panasonic FV-0511VQL1 Manuale utente

Panasonic

Panasonic FV-08VRL1 Manuale utente

Panasonic

Panasonic WhisperGreen FV-08VKS2 Manuale utente

Panasonic

Panasonic FV-07VB1 Manuale utente

Panasonic

Panasonic FV-10VEC2 Manuale utente

Panasonic

Panasonic PAW-FC Manuale

Panasonic

Panasonic FV-08VKL4 Manuale utente

Panasonic

Panasonic WhisperCeiling FV-15VQ4 Manuale operativo e di manutenzione

Panasonic

Panasonic FV-0510VS1 Manuale utente

Panasonic

Panasonic FV-11VH1 Manuale utente

Panasonic

Panasonic F-307KH Manuale utente

Panasonic

Panasonic F-60FEN Manuale utente

Panasonic

Panasonic FV-12NS3 Manuale utente

Panasonic

Panasonic FV-11VQD2 Manuale utente

Panasonic

Panasonic FV-08-11VFM5 Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio

Litex Industries

Litex Industries E-CGL52CB5C1 Manuale utente

Lindab

Lindab LTDF Manuale utente