Panasonic EYFLA4AR Manuale utente

© Panasonic Corporation 2016

Unauthorized copying and distribution is a violation

of law.

Order Number PTD1601E08CE

Cordless Impact Driver / Cordless Impact Wrench

Model No. EYFLA4AR

EYFLA5AR

(Cordless Impact

Driver)

Model No. EYFLA5QR

EYFLA6JR

(Cordless Impact

Wrench)

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Service Fixture and Adjustment----------------------------- 6

5 Disassembly and Assembly Instructions ---------------12

6 Measurements and Adjustments---------------------------21

7 Wiring Connection Diagram ---------------------------------24

8 Schematic Diagram ---------------------------------------------25

9 Exploded View and Replacement Parts List -----------26

2

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70F (30 - 40C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20F (400 ± 10C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100F / 600C).

2 Specifications

3

3 Troubleshooting Guide

4

5

6

4 Service Fixture and Adjustment

4.1. Check Parts Identify Procedure

7

8

9

4.2. Initializing and Setting

NOTE:

• This section explains how to revert all tool settings to their default values at the time of shipment from the factory.

• The error display will be turned off.

INITIALIZING ALL SETTINGS.

1. Set the tool to configuration mode.

(See the next procedure SETTINGS THE TOOL TO

CONFIGURATION MODE.)

2. Press the format button.

a. The control panel will begin flashing.

DISPLAY: The letter “F” flashes on and off.

BATTERY INDICATION LAMP: The upper and lower

bars of the battery flash on and off.

3. Press the OK button to accept the selected setting.

a. The control panel will stop flashing and light up.

SETTINGS THE TOOL TO CONFIGURATION MODE.

1. Turn off the control panel.

If the control panel is on, remove and then reinsert the

battery pack.

2. Engage the switch while pushing the button and then

release both the button and the switch.

a. After all the LED lamps have turned off, the control

panel will flash and change to configuration mode.

10

CONFIGURING THE TORQUE CLUTCH SETTING.

1. Press the (+) and (-) buttons to select the clutch setting

that is appropriate for the work being performed.

a. “F” indicates that the torque control function is off.

b. You can select from 30 torque clutch settings (1 to

30).

2. Press the OK button to accept the selected torque clutch

setting.

a. The control panel will stop flashing and light up.

NOTE:

You must press the OK button in order for the selected

setting to take effect.

SETTING THE SNUG POINT DETECTION LEVEL.

1. Press the torque setting mode button.

a. The snug point detection level setting value will be

displayed.

2. Press the (+) and (-) buttons to set the best snug point

detection level for the work you are performing.

3. Press the OK button to accept the number of torque

stages and the snug point detection level.

a. The tool’s panel will flash and then light up continu-

ously.

Questo manuale è adatto per i seguenti modelli

3

Indice

Altri manuali Panasonic Avvitatore a impulsi

Panasonic

Panasonic EY-6506 Manuale utente

Panasonic

Panasonic EY75A1 Manuale utente

Panasonic

Panasonic EY6506-U1 Manuale utente

Panasonic

Panasonic EYFPA1J Manuale utente

Panasonic

Panasonic EY7201 - 12V IMPACT Manuale utente

Panasonic

Panasonic EY7430 Manuale utente

Panasonic

Panasonic EY7201-X8 Manuale utente

Panasonic

Panasonic EY6588 Manuale utente

Panasonic

Panasonic EYFLF1XC Manuale utente

Panasonic

Panasonic EYFLB1A Manuale utente

Panasonic

Panasonic EY75A7 Manuale utente

Panasonic

Panasonic EY7271 Manuale utente

Panasonic

Panasonic EY7206GQW Manuale utente

Panasonic

Panasonic EY76A1 Manuale utente

Panasonic

Panasonic EY7201 - 12V IMPACT Manuale utente

Panasonic

Panasonic EY75A1 Manuale utente

Panasonic

Panasonic EY7270 Manuale utente

Panasonic

Panasonic EY7552 Manuale utente

Panasonic

Panasonic EY75A1X Manuale utente

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manuale utente

Panasonic

Panasonic EYFPA1J Manuale utente

Panasonic

Panasonic EY75A7 Manuale utente

Panasonic

Panasonic EYFLA1A - DRILL - MULTI LANGUAGE Manuale utente

Panasonic

Panasonic EY75A1 Manuale utente

Manuali Avvitatore a impulsi popolari di altre marche

stayer

stayer IW500D Manuale utente

Makita

Makita DTD152 Manuale utente

Milwaukee

Milwaukee M12 FID Manuale utente

Grizzly

Grizzly H6140 Manuale utente

Makita

Makita BTW450 Manuale utente

Ozito

Ozito LID-3000 Manuale utente

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manuale utente

Greenlee

Greenlee HW3 Manuale utente

Sthor

Sthor 57091 Manuale utente

Makita

Makita DTD145 Manuale utente

Hilti

Hilti SIW 2-A12 Manuale utente

Ryobi

Ryobi R18IW3 Manuale utente

Parkside

Parkside PDSSA 20-Li A1 Manuale utente

Flex

Flex FX1471 Manuale utente

SATA

SATA 51075C Manuale tecnico

Cembre

Cembre NR-11P Manuale utente

Makita

Makita BTP131RFE Manuale utente

DeWalt

DeWalt XR Li-ion DCF902 Manuale utente