Panasonic ET-LAD60A Manuale utente

TQZJ337-6

SS0910AM6042 -PS

Printed in Japan

Model No. ET-LAD60A (1pc)(X1)（1 個入）

Model No. ET-LAD60AW(2pcs)(X2)（2個入）

ENGLISH

FRANÇAIS

日本語

Operating Instructions

Instructions d’utilisation

取付説明書

Replacement lamp unit Commercial Use

Remplacement de l’unité de lampe Usage commercial

交換用ランプユニット 業務用

Read these instructions completely before operating this unit.

• Thank you for purchasing this Panasonic product.

• Before using this product, be sure to read [Read this first!] (Page E-1).

Prière de bien lire toutes ces instructions avant l’utilisation de l’appareil.

• Nous vous remercions d’avoir acheté un produit Panasonic.

• Avant d’utiliser ce produit, assurez-vous de lire [Pour votre sécurité!] (Page F-1).

このたびは、パナソニック製品をお買い上げいただき、まことにありがとうございます。

お客様へ■

この「取付説明書」は、専門業者様用です。取付作業は、必ず専門業者にご依頼ください。

また、取付作業完了後は、この「取付説明書」を専門業者様よりお受け取りのうえ、大切に保管してください。

専門業者様へ■

この「取付説明書」をよくお読みのうえ、正しく安全に作業を行ってください。

また、J-1ページの、「安全上のご注意」は、重要な内容ですので、必ずお読みください。

取付作業完了後は、この「取付説明書」をお客様にお渡しください。

E-1

WARNING

Remove the power plug before replacing the lamp unit.■

If the lamp unit is replaced without removing the power plug, electric shocks and breakage may occur.•

Wait until the lamp is cooled sufficiently before replacing the lamp unit (wait one hour■

or longer).

The lamp cover gets very hot, and contact with it can cause burns.•

Do not remove any screws (such as the black screws) other than those indicated■

when replacing the lamp unit.

If this is not observed, electric shocks, burns or other injuries may occur.•

Notes on replacing the lamp unit

The light source lamp is a glass component. If it is hit on a hard object or dropped, breakage may occur.•

Be careful when handling a light source lamp.

A Phillips screwdriver is necessary when replacing the lamp unit and air filter. (Air filters are used only in the PT-•

DZ570 series)

Hold the screwdriver firmly.

Grip the handle when you remove the lamp unit. Some parts of the lamp unit are sharpened and may cause•

injury.

Lamp may break. Care should be taken not to shatter the broken glass pieces of the lamp when replacing•

the lamp unit. If the projector is installed on the ceiling, do not carry out any replacement procedure directly

underneath the lamp unit and keep your face away from the unit.

The lamp contains mercury. Contact the local government office or distributor for the correct disposal of the old•

lamp unit.

Do not disassemble or modify the lamp unit.•

NOTICE

For USA only

Hg-LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws,

See: www.lamprecycle.org or 1-888-411-1996

Read this rst! Always follow these precautions

Accessories

Check that the following accessories are contained.

Air filter (for the PT-DZ570 series)

ET-LAD60A: x 1

ET-LAD60AW: x 2

Dispose of the packaging materials properly after unpacking the product.•

E-2

ENGLISH

Replacing the lamp unit and air filter

For the PT-DZ570 series

Replacement procedure■

1) Turn off the MAIN POWER

switch, remove the power plug

from the power outlet, and then

wait at least one hour before

checking whether the area

surrounding the lamp unit has

cooled down.

2) Use a Phillips screwdriver to

completely loosen the lamp unit

cover screw (x 1), and open the

lamp unit cover in the direction

of the arrow.

Lamp unit cover screw

Lamp unit cover

3) Use a Phillips screwdriver to

completely loosen the exhaust

fan screw.

Exhaust fan screw

4) Open the exhaust fan as shown,

use a Phillips screwdriver to

completely loosen the lamp

unit fixing screws (x 3), and

gently pull the lamp unit out of

the projector while holding the

handles.

Lamp unit fixing screws

Exhaust fan

Handles

If the projector is operating, turn off the power by the following procedure and wait for the lamp unit to cool down•

before carrying out replacement.

# Press the power ( ) button on the projector or on the remote controller.

$ Select “Execute” with or button and press the ENTER button.

(or press the power ( ) button again.)

The projection of the image stops, and the power indicator lamp of the main unit lights orange.

(The cooling fan keeps running.)

Wait until the power indicator lamp on the front of the projector turns red (i.e., until the

cooling fan stops). (Approx. 3 minutes)

Press the “ ” marked side of the MAIN POWER switch to remove all power from the

projector.

E-3

5) Position the new lamp unit correctly and install it.

Grooves for lamp unit installation guides

Lamp unit installation guides

6) Use a Phillips screwdriver to securely tighten the lamp unit fixing screws

(x 3).

7) Remove the air filter.

Grasp the tab on the air filter and

gently pull it out.

8) Install the new air filter.

Insert the air filter with the grid side facing the bottom of the projector.

The air filter must always be installed in the projector. Failure to do so will result in malfunctions due to•

foreign materials, such as dust, entering the projector.

Insert the air filter all the way into the projector.•

Do not wash the air filter with water. Doing so will degrade its dust-resistant properties.•

Always replace the air filter whenever replacing the lamp unit.•

9) Close the exhaust fan, and use a Phillips screwdriver to securely tighten

the exhaust fan screw.

10) Close the lamp unit cover, and use a Phillips screwdriver to securely

tighten the lamp unit cover screw (x 1).

Firmly install the lamp unit and lamp unit cover.•

When a lamp unit is replaced with a new unit, the cumulated time of the lamp unit is reset automatically by the•

projector.

Air filter

Replacing the lamp unit and air filter (continued)

E-4

ENGLISH

For the PT-DZ6700 series /PT-DW730 series /

PT-DZ770 series /PT-DZ680 series

Replacing the lamp unit

If the projector is operating, turn off the power by the following procedure and wait for the lamp unit to cool down•

before carrying out replacement.

Confirm the status of the lamp monitors (lamp indicators) <LAMP1> and <LAMP2> on the front of the projector.•

The lamp unit corresponding to the lamp monitor (lamp indicator) <LAMP1> or <LAMP2> lit in red needs to be

replaced.

Press the STANDBY ( ) button on the projector or on the remote controller.

$ Select “Execute” with or button and press the ENTER button.

(or press the STANDBY ( ) button again.)

The projection of the image will stop and the power monitor (power indicator) <STANDBY (RED)/ON

(GREEN)> of the projector will light up in orange. (The fan keeps running.)

Wait until the power monitor (power indicator) on front of the projector changes to red (i.e.,

until the fan stops).

& Turn the power off by pressing the

“ ”

side of the <MAIN POWER> switch (<OFF> side).

Replacement procedure■

1) Turn off the MAIN POWER switch, remove the power plug from the

power outlet, and then wait at least one hour before checking whether

the area surrounding the lamp unit has cooled down.

# Use a Phillips screwdriver to completely loosen the lamp unit cover

screw (x 1), and open the lamp unit cover in the direction of the arrow.

$ Slide the lamp unit cover toward the control buttons while holding it

tightly, and pull it outward to remove it.

3) Use a Phillips screwdriver to completely loosen the fixing screws for the

lamp units (x 3 each), and hold the handles to pull the lamp units out.

Handles Lamp unit 1

Lamp unit 2

Fixing screws

①

②

Lamp unit cover

Lamp unit cover screw

E-5

4) Insert the new lamp unit taking care of the inserting direction.

5) Use a Phillips screwdriver to securely tighten the fixing screws for the

lamp units (x 3 each).

6) # Attach the lamp unit cover so that the mark aligns with .

$ Slide the lamp unit cover in the direction of the arrow to fit it in place,

and then tighten the lamp unit cover screw.

Firmly install the lamp unit cover so that the connector on the lamp unit cover side is securely inserted into•

the fan power connector.

If the projector is mounted on the ceiling, do not work with your face close to the lamp unit.•

Attach the lamp unit and lamp unit cover securely.•

Remove the lamp unit once and reinsert it when the lamp unit does not insert smoothly. The connector may•

be damaged when inserted forcefully.

①

②

Lamp unit cover

Fan power connector

Lamp unit cover screw

Replacing the lamp unit (continued)

When a lamp unit is replaced with a new unit, the cumulated time of the lamp unit is reset automatically by•

the projector.

E-6

ENGLISH

EEE Yönetmeliğine Uygundur.

EEE Complies with Directive of Turkey.

Disposal of Old Equipment

Only for European Union and countries with recycling systems

This symbol on the products, packaging, and/or accompanying documents means that used electrical

and electronic products must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Panasonic Accessori per proiettori

Panasonic

Panasonic PressIT TY-WPS1 Manuale utente

Panasonic

Panasonic ET-LAV200C Manuale utente

Panasonic

Panasonic ET-MD77NT Manuale utente

Panasonic

Panasonic ET-LAD40 Guida

Panasonic

Panasonic PressIT TY-WPS1W Istruzioni operative

Panasonic

Panasonic ET-PFD560 Manuale utente

Panasonic

Panasonic ET-ELW21C Manuale utente

Panasonic

Panasonic ET-DLE030 Manuale utente

Panasonic

Panasonic ET-LEC701 Guida

Panasonic

Panasonic ET-LAV100 Manuale utente

Panasonic

Panasonic PressIT TY-WP2B1 Manuale utente

Panasonic

Panasonic ET-LAE200 Manuale utente

Panasonic

Panasonic PressIT TY-WP2B1W Istruzioni operative

Panasonic

Panasonic ET-MWP100G Guida rapida

Panasonic

Panasonic ET-LAEF100C Manuale utente

Panasonic

Panasonic ET-ELW02 Manuale per l'uso e la cura

Panasonic

Panasonic ET-LAD7700 Guida

Panasonic

Panasonic ET-DLE170 Manuale utente

Panasonic

Panasonic ET-EMF330C Manuale utente

Panasonic

Panasonic ET-PKE200H Manuale utente

Panasonic

Panasonic ET-DLE050 Manuale del sistema

Panasonic

Panasonic ET-D75LE8 Manuale del sistema

Panasonic

Panasonic ET-SFR330 Manuale utente

Panasonic

Panasonic ET-LAL500 Manuale utente

Manuali Accessori per proiettori popolari di altre marche

Optoma

Optoma BX-AL133B Manuale utente

PEERLESS

PEERLESS PE 1120 Guida

Osram

Osram SIRIUS HRI Series Manuale

Presentation Switchers

Presentation Switchers PS111 Manuale utente

Kramer

Kramer VIA GO Manuale utente

Yamaha

Yamaha PJL-112 Manuale elenco delle parti

Swedstyle

Swedstyle CL23AA02ZA25E Manuale utente

Mitsubishi Electric

Mitsubishi Electric 236CB Manuale del proprietario

Epson

Epson BrightLink 475Wi Manuale utente

Acer

Acer WP100 Manuale utente

i3 i3board Manuale utente

CHIEF

CHIEF HB-43E Manuale utente

Biamp

Biamp Modena Hub Manuale di servizio

NEC

NEC MP10RX Manuale utente

Panamorph

Panamorph DCR-S3 Manuale utente

Exact solutions

Exact solutions FRAME-EVO-P10 Manuale utente

CHIEF

CHIEF VCM103S Manuale utente

InFocus

InFocus LP70+ Guida