Panasonic BB-HGW700A - Network Camera Router Manuale utente

ORDER NO. KMS0411022C1

Network Camera Management System

BB-HGW700A

(for U.S.A.)

Unauthorized copying and distribution is a violation of law.

IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING

If lead free solder was used in the manufacture of this product the printed circuit boards will be marked

PbF.

Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.

When this mark does appear please read and follow the special instructions described in this manual

on the use of PbF and how it might be permissible to use Pb solder during service and repair work.

1. ABOUT LEAD FREE SOLDER (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard

solder or solder that contains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which

is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB.

For service and repair work we suggest using the same type of solder although, with some precautions,

standard Pb solder can also be used.

Caution

- PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher

than Pb solder. Please use a soldering iron with temperature control

and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high

temperature soldering iron, please be careful not to heat too long.

- PbF solder will tend to splash if it is heated much higher than its melting

point, approximately 1100°F, (600°C).

- If you must use Pb solder on a PCB manufactured using PbF solder,

remove as much of the original PbF solder as possible and be sure that

any remaining is melted prior to applying the Pb solder.

- When applying PbF solder to double layered boards, please check the

component side for excess which may flow onto the opposite side (See

figure, below).

1.1. SUGGESTED PbF SOLDER

There are several types of PbF solder available commercially. While this product is manufactured using

Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and

Bismuth, (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of

their products and any precautions for using their product with other materials. The following lead free

(PbF) solder wire gauge are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDEmpR IS USED

2. FOR SERVICE TECHNICIANS

ICs and LSIs are vulnerable to static electricity.

When replacing, the following precautions will help to prevent recurring malfunctions.

1. Cover the plastic parts with aluminum foil.

2. Ground the soldering irons.

3. Use a conductive mat on the work-table.

4. Do not grasp IC or LSI pins with bare fingers.

3. CAUTION

3.1. SAFETY PRECAUTIONS

1. Before servicing, unplug the power cord to prevent an electrical shock.

2. When replacing parts, use only manufacturer’s recommended

components for safety.

3. Check the condition of power cord. Replace if wear or damage is

evident.

4. After servicing, be sure to restore the lead dress, insulation barriers,

insulation papers, shields, etc.

5. Before returning the serviced equipment to the customer, make the

following insulation resistance test to prevent a shock hazard.

3.2. INSULATION RESISTANCE TEST

1. Unplug the AC power cord and short the two prongs of the plug with a

jumper wire.

2. Measure the resistance value with ohmmeter between the jumpered AC

plug and each exposed metal cabinet part, such as screw threads, etc.

Note:

Some exposed parts may be isolated from the chassis by design. These will read infinity.

3. If the measurement is outside the specified limits, there is a possibility

of shock hazard. The equipment should be repaired and rechecked

before it is returned to the customer.

3.3. POWER CAUTION

The power socket wall outlet should be located near this equipment and be easily accessible.

4. SPECIFICATIONS

Main Unit

Heading Specifications

Power Supply Special AC Adaptor:

(Part Number: PQLV202Y)

INPUT: AC120V, 60 Hz

OUTPUT: DC120 V, 750mA

DC Cord: approx 3m

AC Cord: approx 1.7m (attached separately)

Power

Consumption

Maximum: approx 6W

Dimensions

(Width x Height

x Depth)

About 204mm (8.0inches) x About 36mm (1.4inches) x About 140mm (5.5inches)

(when the antenna is stored)

Weight 330g (0.7 lb)

Environmental

Requirements

Temperature (°C):

Humidity (%):

0 - 40 (32 - 104°F)

20 - 85 (non-condensing)

WAN Interface Number of Ports:

Connector Shape:

Physical Interface:

Throughout between

WAN and LAN (value

measured at Panasonic):

8 pin modular jack (RJ-45)

IEEE 802.3 (10Base-T)

IEEE 802.3u (100Base-TX)

Maximum of 98Mbps (IPv4/SmartBits)

Maximum of 77Mbps (IPv6/SmartBits)

Maximum of 16Mbps (FTP[PPTP])

LAN Interface Number of Ports:

Connector Shape:

Physical Interface:

8 pin modular jack (RJ-45)

IEEE 802.3 (10Base-T)

IEEE 802.3u (100Base-TX)

Wireless

Interface

Wireless Chip: made by Atheros Communications

IEEE 802.11b

Transmission Method:

Transmission Speed

([Standard value]Mbps):

Frequency Range (MHz):

Number of Channels:

Security:

DS-SS, half-duplex

11/5.5/2/1* (complying to IEEE 802.11b): automatic fallback

2412 - 2462 (center frequency)

WPA-PSK (TKIP), WPA2-PSK (AES), WEP (64 bit/128 bit/152

bit), SSID, stealth SSID (hidden SSID, permitting/not

permitting connection using the ANY key), MAC address

filtering

IEEE 802.11g

Transmission Method:

Transmission Speed

([Standard value]Mbps):

Frequency Range (MHz):

Number of Channels:

Security:

OFMD (complying to IEEE 802.11g)/DS-SS (compatible with

IEEE 802.11b), half-duplex

54/48/36/24/18/12/9/6* (complying to IEEE 802.11g):

automatic

fallback

2412 - 2462 (center frequency)

WPA-PSK (TKIP), WPA2-PSK (AES), WEP (64 bit/128 bit/152

bit), SSID, stealth SSID (hidden SSID, permitting/not

permitting connection using the ANY key), MAC address

filtering

-The figures shown are theoretical maximums and not the actual figures when using the product.

Heading Specifications

User Interface FACTORY

DEFAULT

RESET button:

Status

Indicators

POWER:

WAN:

PPP:

LAN1-

LAN4:

WIRELESS

Returns the product to factory default settings.

Displays the power/main unit status

Displays the WAN link status

Displays the PPP link status

Displays the Ethernet link status

Displays the wireless link status

Software

Heading Specifications

Router Function WAN Side Connection

Mode:

PPPoE Connection:

RIP:

DHCP Server:

DNS Relay (DNS proxy

answering):

IP Packet Filtering:

Address Translation

Method:

PPPoE/DHCP/Static

Always/Manual

Yes (RIPv2)

Yes (128 client setup is possible)

Yes

Yes (64 setup)

IP masquerade, port forwarding

Wireless Device

Function

Security: WPA-PSK (TKIP), WPA2-PSK (AES), WEP (64 bit/128 bit/152

bit), stealth SSID (hidden SSID, permitting/not permitting

connection using the ANY key), MAC address filtering

Access Control ID/Password

Web Browser

Setup

Yes

Firmware Update Yes

5. PARTS LOCATIONS

5.1. FRONT VIEW

5.2. REAR VIEW

6. SYSTEM REQUIREMWNTS

The PC (Personal Computer) and the network must meet the following technical specifications for the

BB-HGW700A to work properly.

Item Description

Operating System Microsoft Windows 98 SE / Microsoft Windows Me /

Microsoft Windows 2000 / Microsoft Windows XP

Interface 10/100 Mbps Ethernet card and Ethernet cables for your

network

connection

RAM 64MB or more

Protocol TCP/IP network protocol installed

Web Browser Internet Explorer 6.0 or later

Compatible network cameras (Customer-provided): (as of Nov. 2004)

Indoor type

KX-HCM8

KX-HCM10

KX-HCM250

KX-HCM280

BB-HCM311A

BL-C10A

BL-C30A

Outdoor type

KX-HCM230

KX-HCM270

BB-HCM331A

7. CONNECTIONS

7.1. INTERNET CONFIGURATION WITH OPTICAL CABLE OR CABLE/

xDSL MODEM - (TYPE 1)

8. DISASSEMBLY INSTRUCTIONS

8.1. HOW TO REMOVE THE CABINET COVER

1. Remove two Screws (A).

2. Remove the Cabinet Cover.

8.2. HOW TO REMOVE THE MAIN BOARD AND ANTENNA

Altri manuali per BB-HGW700A - Network Camera Router

Indice

Altri manuali Panasonic Telecamera di sicurezza

Panasonic

Panasonic Super Dynamic III WV-CW974 Manuale utente

Panasonic

Panasonic WV-CP110E Manuale utente

Panasonic

Panasonic WV-CPR460 Manuale utente

Panasonic

Panasonic WV-SFR631L Manuale utente

Panasonic

Panasonic WVCF254 - COLOR CAMERA Manuale utente

Panasonic

Panasonic AK-HC1800G Manuale utente

Panasonic

Panasonic BB-HCM371A - Outdoor Wireless Network Camera Manuale utente

Panasonic

Panasonic WV-SW395 Manuale utente

Panasonic

Panasonic WV-BP140 Manuale utente

Panasonic

Panasonic KX-HCM280 Manuale utente

Panasonic

Panasonic AWHE60H Manuale utente

Panasonic

Panasonic BL-C230 Series Manuale utente

Panasonic

Panasonic WV-NP304 Manuale utente

Panasonic

Panasonic Super Dynamic III WV-CP484 Manuale utente

Panasonic

Panasonic Super Dynamic III WV-CW964 Manuale utente

Panasonic

Panasonic WV-CW384E Manuale utente

Panasonic

Panasonic WV-NP304E Manuale utente

Panasonic

Panasonic WV-X2551LN Guida all'installazione

Panasonic

Panasonic WV-CP240EX Manuale utente

Panasonic

Panasonic WVCS574 - COLOR CCTV CAMERA Manuale utente

Panasonic

Panasonic WV-SP509 Manuale utente

Panasonic

Panasonic WV-SFR311 Manuale utente

Panasonic

Panasonic AK-HC1500G Manuale utente

Panasonic

Panasonic BB-HCM531A - Network Camera Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente