Panduit CT-1003 Manuale di istruzioni

Page: 1 of 2

CONTROLLED CYCLE FERR LE CRIMPING TOOLS

OPERATION, INSPECTION and MAINTENANCE INSTR CTIONS

1. With the handles in

the open position,

insert the ferrule

into the opening at

the top of the tool.

Make sure that the

ferrule insulation or

flared end is up

(see Figure 2). Do

not allow insulation

to be inserted into

crimp die. Close

handles until dies

just slightly crimp

ferrule.

2. Insert the stripped wire into the ferrule until the wire

stops. Refer to product packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. pon release,

the handles will open automatically and the crimped

ferrule can be removed.

1. With the handles in

the open position,

insert the ferrule

into the crimp

pocket. Make sure

that the ferrule is

inserted fully into

the crimp die (see

Figure 4).

2. Insert the stripped

wire into the ferrule

until the wire stops.

Refer to product

packaging for wire

strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. pon release,

the handles will open automatically and the crimped

ferrule can be removed.

NOTE: Crimp entire uninsulated ferrule length. This may

require additional crimps.

CT-1002, CT-1003 and CT-1004 TOOLS

CT-1005 and CT-1006 TOOLS

Cushioned handle grips

CRIMP POCKET for Insulated

and Non-Insulated Ferrules. Part

usage dependent on wire range.

Refer to product packaging for

proper wire combination.

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is complete.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Fig. 1

Fig. 3 Fig. 4

Fig. 2

Stripped

Wire

Crimp Die

Die Closure Alignment

(not a crimp pocket)

Controlled cycle mechanism pre-

vents tool from opening before

crimp cycle is completed.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Cushioned handle grips

Ferrule

Insulation

section Ferrule -

Metal crimp

section

Stripped

Wire

CRIMP POCKETS for Ferrule

terminals. Refer to product

packaging for wire range and

proper crimp pocket. Crimp

pockets are identified with

applicable wire range.

Ferrule - Wire

crimp section

Ferrule Insulated

section

CT-1002, CT-1003, CT-1004,

CT-1005 and CT-1006

PA24073A01

REV: 03 10-2014

E-mail:

techsupport@panduit.com

For Technical Support:

1-888-506-5400, ext. 83255

www.panduit.com

CAUTION:

Verify power is “OFF” before working

on wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock

while working on li e electrical circuits.

Page: 2 of 2

NEW TOOLS - BEFORE PLACING INTO SERVICE:

All Panduit crimping tools are inspected before they are shipped from the factory. All new tools should be inspected

before being used.

New tools are shipped, factory lubricated, in protective packaging. After inspection, simply clean any excess oil from the

crimping dies and place into service.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping area. Store

the tool in a clean, dry area.

IN SERVICE TOOLS - AFTER TOOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing

surfaces with DOW CORNING®Molykote BR2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.

INSPECTION / MAINTENANCE

VIS AL INSPECTION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.

4. Check for debris in dies. Any debris will need to be removed prior to tool use.

OPERATION, INSPECTION and MAINTENANCE INSTR CTIONS

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Panduit Utensili per crimpatura

Panduit

Panduit Contour Crimp CT-1015 Manuale utente

Panduit

Panduit CT-1104 Manuale di istruzioni

Panduit

Panduit BlackFin CT-2980/STBT Manuale utente

Panduit

Panduit Contour Crimp CT-1551 Manuale utente

Panduit

Panduit CT-2500 Manuale utente

Panduit

Panduit Black Fin CT-2931 Series Manuale utente

Panduit

Panduit BlackFin CT-2920 Manuale utente

Panduit

Panduit CT-930LPCH Manuale utente

Panduit

Panduit CTFP-100 Manuale utente

Panduit

Panduit BlackFin CT-2931/STBT Manuale utente

Panduit

Panduit BlackFin CT-2980/ST Manuale utente

Panduit

Panduit CT-2940/L Manuale utente

Panduit

Panduit Ezair CA9 Manuale utente

Panduit

Panduit CT-1123 Manuale di istruzioni

Panduit

Panduit BlackFin CT-2600/LBT Manuale utente

Panduit

Panduit CT-3001 Manuale utente

Panduit

Panduit CT-920 Series Manuale utente

Panduit

Panduit Blackfin CT-2980/TO Manuale utente

Panduit

Panduit CT-1002 Manuale

Panduit

Panduit PAT4.0 Series Manuale utente

Panduit

Panduit BlackFin CT-3980/BT Manuale utente

Panduit

Panduit CT-1000 Manuale utente

Panduit

Panduit Black Fin CT-2931/STCVUK Manuale utente

Panduit

Panduit CT-460 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente