Paradyne Hotwire 8775 Manuale utente
TM
1
8775-A2-GZ40-10 March 1999
Hotwire8775 M/SDSL Termination Unit
Installation Instructions
Document Number 8775-A2-GZ40-10
March 1999
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the
waste of surplus printing. It also helps us maintain competitive prices for our
products.
Complete documentation for this product is available at www.paradyne.com.
Select
Library
→
Technical Manuals
→
Hotwire DSL & MVL Systems.
Select the following document:
8775-A2-GB20
Hotwire 8775 M/SDSL Termination Unit User’s Guide
To request a paper copy of a Paradyne document:
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Hotwire8775 E1 M/SDSL Termination Unit
The Hotwire 8775 Termination Unit is a circuit card assembly (CCA) that contains
four E1 Multirate Symmetric Digital Subscriber Line (M/SDSL) ports. When the
8775 Termination Unit is used in a Hotwire 8600 or 8800 Series Digital Subscriber
Line Access Multiplexer (DSLAM) chassis, it transports 2048 kbps signals over
traditional twisted-pair telephone wiring.
!HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
496-15104
2 8775-A2-GZ40-10
March 1999
Installation Overview
Installation and configuration of the Hotwire 8775 Termination Unit consists of:
HInstalling the Termination Unit in the DSLAM.
HConnecting to the DTE.
HConnecting to an MDF.
HProviding initial unit identity information or changing existing identity
information.
HConfiguring your unit using the Configuration Edit menus.
Before you install the Hotwire 8775 Termination Unit, read the
Important Safety
Instructions
on page 23.
Be sure to register your warranty at www.paradyne.com. Select
Service &
Support
→
Warranty Registration.
Tool Required
-Small- to medium-size flat-blade screwdriver.
Planning the 8775 Termination Unit Installation
Review the following list to help plan for the installation.
-Obtain the applicable cables; refer to
Cables You Need
on page 3.
-Make sure the Hotwire DSLAM chassis is installed and power is supplied to
the chassis.
-After the 8775 Termination Unit is installed, there are configuration
procedures that must be performed before you can begin to use the 8775
Termination Unit. Refer to the User’s Guide for more detailed configuration
procedures.
3
8775-A2-GZ40-10 March 1999
Cables You Need
The following customer-provided cables are used with this product.
For the network connection:
Plug-ended Telco 50-pin cable for connection from the Hotwire 8600 DSLAM
LINE port or one of the Hotwire 8800 DSLAM LINES ports to the Main
Distribution Frame (MDF) or other demarcation point.
For the DTE connection, one of the following:
100-pin plug to four DB15 (X.21)
100-pin plug to four DB25 (EIA-530A)
100-pin plug to four DB37 (RS-449)
100-pin plug to four MS34 (V.35)
For more information refer to
Cables and Pin Assignments
in the User’s Guide.
Installing DSL Cards
Use a small- to medium-size flat-blade screwdriver to install the 8775 Termination
Unit.
When using a . . . Install the 8775 Termination Unit in . . .
Hotwire 8600 Series
DSLAM base chassis Slot 2 or 3. Slot 1 of the Hotwire 8600 DSLAM base
chassis must contain a Management Communications
Controller (MCC) card.
Hotwire 8600 Series
DSLAM expansion chassis Slot 1, 2, or 3.
Hotwire 8800 Series
DSLAM chassis Any one of the first 18 slots (i.e., Slots 1 through 18).
Slot 19 is reserved for the MCC and Slot 20 is reserved for
future use.
An 8775 Termination Unit can be installed, removed, and replaced from a Hotwire
DSLAM chassis without disrupting service to the other cards in the chassis.
NOTE:
When installing the 8775 Termination Unit, you need to remove the filler plate
before proceeding.
Do not discard unused filler plates. Each slot in the chassis must contain a
circuit card or a filler plate. Store all unused filler plates in a safe place. You
may need to use the filler plates to cover open slots in the chassis at a later
time.
4 8775-A2-GZ40-10
March 1999
Procedure
To install an 8775 Termination Unit:
1. Determine in which slot the 8775 Termination Unit will be installed. Verify that
cards in adjacent slots have been fastened.
2. Remove the filler plate from the installation slot.
3. Insert the 8775 Termination Unit:
— For a Hotwire 8600 Series DSLAM chassis – hold the 8775 Termination
Unit horizontally with component side facing up and insert it into the left
and right card guides.
A
INPUT
AC
48VDC CLASS 2 OR
LIMITED PWR SOURCE
RTN48V
AAB B
LAN/WAN SLOT
2
46
B
.
.
.
3.
1
2
POSITION
STACK ALM A
IN
B
DC FUSES 5DC PWR
FAN
OUT SERIAL MCC 1
MANAGEMENT
3
LINE 1
2
3
98-15832
SYSTEM
OKAlrm
Test
TXRXCol
ETHERNET
M/SDSL
8775
SYSTEM
OKAlrm
Test
TXRXCol
1234
ETHERNET
DSL PORT
ESD
— For a Hotwire 8800 Series DSLAM chassis
–
hold the 8775 Termination
Unit vertically with component side facing right and insert it into the top
and bottom card guides.
ALARMS
Major MinorFanBA
POWER
MCC
SYSTEM
OK
Alm
Test
ETHERNET
TX
RX
Coll
98-15328-01
MGT
SERIAL
MGT
10BT ALARM
SLOTS 1 - 6
SLOTS 7-12
SLOTS 13-18
LINES
AB
-48V (A)
-48V INPUT
-48V (B)
RET (A)
RET (B)
FR GND
246810 12 14 16 18
19
1357911 13 15 17
LAN/WAN SLOT 20
LAN/WAN SLOT
Slot 1
DSL
SYSTEM
OK
Alm
Test
ETHERNET
TX
RX
Coll
DSL PORT
1
2
3
4
DSL Card
5
8775-A2-GZ40-10 March 1999
4. Slide the 8775 Termination Unit into the slot until the power and network
connectors seat firmly in the mating connectors on the backplane.
CAUTION:
Do not force the 8775 Termination Unit into the slot. This could damage
the backplane connectors. If the card does not seat properly, remove
the card and reinstall it. If it still does not seat properly, call your
service representative.
The 8775 Termination Unit performs a power-up self-test. All of the LEDs turn
ON and OFF briefly. When the self-test is completed successfully, the
SYSTEM OK LED will turn ON. Make sure the SYSTEM OK indicator on the
8775 Termination Unit faceplate is ON.
5. If the LED is not ON, refer to
Messages and Troubleshooting
in the User’s
Guide.
6. Secure the 8775 Termination Unit by fastening the screws at each end of the
faceplate.
NOTE:
The 8775 Termination Unit may be replaced without system disruption (i.e.,
you can remove and reinstall a card without powering down the Hotwire
DSLAM chassis and disrupting service to the other cards). To remove an
8775 Termination Unit from the Hotwire DSLAM chassis, unfasten the screws
on both ends of the faceplate. Then push the ejector handles outward and
slide the card out.
Ensure that adjacent cards are fastened before removing a card.
When swapping the old 8775 Termination Unit with a new 8775 Termination
Unit, note that the 8600 DSLAM retains the Media Access Control (MAC)
address, also referred to as the physical address. This means that the new
8775 Termination Unit will have the same MAC address as the old one.
6 8775-A2-GZ40-10
March 1999
Cable Management
The optional Cable Guide connects to the front of the Hotwire 8800 Series
DSLAM and provides strain relief and control of the DTE cables. Install the Cable
Guide before installing the cables.
97-15777
ALARMS
Major MinorFanBA
POWER
MGT
SERIAL
MGT
10BT
ALARM
SLOTS 1 - 6
SLOTS 7-12
SLOTS13-18
LINES
-48V (A)
-48V INPUT
-48V (B)
RET (A)
RET (B)
FR GND
246810 12 14 16 18
19
1357911 13 15 17
LAN/WAN SLOT
20
LAN/WAN SLOT
SLOTS13-18
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703ALRM
DSLPORT
LINK-UP
4
SYSTEM
OKAlrm
Test
123
G.703ALRM
4
Front Rail
Existing
Screw
Bottom Hole for
Mounting in 19"
Rack or Cabinet
Front Rail
Top Hole for
Mounting in 23"
Rack or Cabinet
Screw
Washer
and Nut
7
8775-A2-GZ40-10 March 1999
Connecting to the DTE Equipment
Connection to the four ports of the 8775 Termination Unit is through the 100-pin
EIA-530 interface connector on its faceplate. Use one of the DTE cables listed
under
Cables You Need
on page 3.
Procedure
To connect the Hotwire 8775 Termination Unit to your DTE equipment:
1. Connect the 100-position connector of the cable to the connector on the
faceplate of the 8775 Termination Unit. Align one end of the cable connector
with the card connector, then push on the cable connector until it seats.
The end of the cable connector has a release button. To remove the
connector, press the release button and pull the connector away from the
card.
97-15726
-48V RTN F
G
ABAB
48VD
ETHERNET
MCC
8000
SYSTEM
OKAlrm
Test
TXRXCol
4
SYSTEM
OKAlrm
Test
123
123
G.703 ALRM
DSL PORT
LINK-UP
4
4
SYSTEM
OKAlrm
Test
123
123
G.703 ALRM
DSL PORT
LINK-UP
4
2. Feed the cable through the Cable Guide if it is in use. When all cables are
installed, anchor them with cable ties to the rack, DSLAM, or Cable Guide.
3. Connect the four terminating connectors to your DTE equipment.
8 8775-A2-GZ40-10
March 1999
Connecting to an MDF
You can connect the Hotwire DSLAM chassis containing the 8775 Termination
Unit to an MDF or other demarcation point. Do not connect it to a POTS splitter.
Procedure
To connect the Hotwire DSLAM chassis containing the 8775 Termination Unit to
an MDF:
1. Plug the Telco 50-pin cable into the appropriate LINE port on the front panel
of the chassis:
—On a Hotwire 8600 Series DSLAM chassis:
98-15833
A
INPUT
AC
48VDC CLASS 2 OR
LIMITED PWR SOURCE
RTN48V
AAB B
LAN/WANSLOT
2
46
B
.
.
.
3.
1
2
POSITION
STACKALM A
IN
B
DC FUSES
T4A, MIN. 48V 5PWR
FAN
OUT SERIAL MCC 1
MANAGEMENT
3
LINE
1
2
3
SYSTEM
OKAlrm
Test
TXRXCol
ETHERNET
MCC
8000
SYSTEM
OKAlrm
Test
TXRXCol
1234
ETHERNET
DSL PORT
M/SDSL
8775
SYSTEM
OKAlrm
Test
TXRXCol
1234
ETHERNET
DSL PORT
M/SDSL
8775
Anchor
Mount
Telco 50-Pin
Connector
ESD
9
8775-A2-GZ40-10 March 1999
—On a Hotwire 8800 Series DSLAM chassis:
SLOTS 13-18
SLOTS 7-12
SLOTS 1-6
97-15325
Anchor Mount
Telco 50-Pin
Connector
LINES
SLOTS 1-6
LINES
Shorter
Telco
Captive Screw
2. Replace the longer Telco cable captive screw with a shorter connector
captive screw, which is provided with the Hotwire DSLAM chassis.
3. Insert a cable tie (provided with Hotwire DSLAM chassis) through the tie
mount to hold the Telco 50-pin connector in place. If more than one Telco
cable is being connected, span the two or three connectors.
4. Make sure the other end is connected to the appropriate MDF or demarcation
point.
Refer to
Cables and Pin Assignments
in the User’s Guide for pinouts.
NOTE:
If you are connecting the Telco 25-pair, 50-pin cable to an MDF, a converter
may be necessary for terminating the other end of the cable on a punchdown
block before cross-connecting to an MDF.
10 8775-A2-GZ40-10
March 1999
8775 Termination Unit LEDs
The following table describes the meaning and states of the LEDs on the 8775
Termination Unit faceplate.
Type LED LED is . . . Indicating . . .
SYSTEM OK Green
Off
Normal operation; card functioning normally.
No power to card, or card failure.
Alrm Amber
Off
Device failure, or Power-On Self-Test (POST)
failure.
No alarms.
Test Amber
Amber,
flashing
Off
Loopback test or 511 test pattern in progress.
POST in progress.
No tests.
SYNC
PORT 1, 2, 3, 4 Green
Amber
Amber,
flashing
Off
Interchange circuits for the port are in the
correct state to transmit and receive data.
The port is configured to monitor DTR and/or
RTS and no monitored lead is asserted.
Data Channel Loopback (DCLB) or Data
Terminal Loopback (DTLB) is active on the
port.
The port is disabled.
DSL PORT
LINK-UP 1, 2, 3, 4 Green
Off
Amber
Amber,
flashing
DSL link is up.
DSL link is down.
DSL training in progress.
OOF condition.
4
M/SDSL
8775
SYSTEM
OKAlrm
Test
123
123
SYNC PORT
DSL PORT
LINK-UP
4
98-15834
Altri manuali per Hotwire 8775
2
Indice
Altri manuali Paradyne Modem
Paradyne
Paradyne HotWire 5170 Manuale utente
Paradyne
Paradyne COMSPHERE 3610 Manuale di istruzioni
Paradyne
Paradyne Hotwire 6210 Istruzioni operative originali
Paradyne
Paradyne Hotwire 7974 Manuale utente
Paradyne
Paradyne KeepInTouch 3766 Manuale utente
Paradyne
Paradyne COMSPHERE 3810 Manuale utente
Paradyne
Paradyne Hotwire 7985 Manuale utente
Paradyne
Paradyne COMSPHERE 3830 Manuale utente
Paradyne
Paradyne 6218-A1-200 Manuale utente
Paradyne
Paradyne COMSPHERE 3810 Manuale utente
Paradyne
Paradyne BitStorm 6200 Manuale utente
Paradyne
Paradyne DataPort Manuale utente
Paradyne
Paradyne COMSPHERE 3910 Manuale del proprietario
Paradyne
Paradyne COMSPHERE 3800 Series Manuale utente
Paradyne
Paradyne Hotwire 7985 Manuale utente
Paradyne
Paradyne 2001 Manuale di istruzioni
Paradyne
Paradyne HotWire 7915 Manuale di istruzioni
Paradyne
Paradyne 7510 Manuale
Paradyne
Paradyne COMSPHERE 3920PLUS Series Manuale utente
Paradyne
Paradyne COMSPHERE 392xPlus Manuale utente
