Paradyne 12000E Manuale utente
IPD1-A2-GZ40-10 July 2005 1
12000E IP Broadband Loop Carrier
Installation Instructions
Document Number IPD1-A2-GZ40-10
July 2005
Contents
Software and Firmware License Agreement ...................................................... 1
Introduction ........................................................................................................ 3
Unpacking and Inspecting the Equipment ......................................................... 3
Installation Options ............................................................................................ 4
Installing Your Management Module .................................................................. 6
Installing Your Interface Module(s) ..................................................................... 9
Establishing Your Uplink Connections ............................................................... 14
Connecting Your Subscriber Lines ..................................................................... 15
Configuration and Management ........................................................................ 18
Product Documentation Online .......................................................................... 18
Fan Module ........................................................................................................ 19
Specifications ..................................................................................................... 20
Important Safety Instructions ............................................................................. 21
Warranty, Sales, Service, and Training Information ........................................... 23
Software and Firmware License Agreement
The terms and conditions of this License Agreement (the “Agreement”) will apply
to the software and/or firmware (individually or collectively the “Software”)
incorporated into the Paradyne product (the “Product”) purchased by you and any
derivatives obtained from the Software, including any copy of either. If you have
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
2July 2005 IPD1-A2-GZ40-10
executed a separate written agreement covering the Software supplied to you
under this purchase, such separate written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to
accept a personal, non-transferable, non-exclusive, right (without the right to
sublicense) to use the Software, solely as it is intended and solely as incorporated
in the Product purchased from Paradyne or its authorized distributor or reseller
under the following terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors.
The Licensee acquires no title, right or interest in the Software other than the
license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in
which the Product was rightfully purchased except upon prior written notice to
Paradyne and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the
Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is
provided “AS IS” and in its present state and condition and Paradyne makes
no other warranty whatsoever with respect to the Product purchased by you.
THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING
WITHOUT LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in
your operating environment, or is compatible with any equipment or
software configurations; and
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied
warranties on limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from one state or jurisdiction to
another.
6. In no event will Paradyne be liable to Licensee for any consequential,
incidental, punitive or special damages, including any lost profits or lost
savings, loss of business information or business interruption or other
pecuniary loss arising out of the use or inability to use the Software, whether
based on contract, tort, warranty or other legal or equitable grounds, even if
Paradyne has been advised of the possibility of such damages, or for any
claim by any third party.
7. The rights granted under this Agreement may not be assigned, sublicensed or
otherwise transferred by the Licensee to any third party without the prior
written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be
terminated in the event of breach by the Licensee of any provisions of this
Agreement.
IPD1-A2-GZ40-10 July 2005 3
9. Upon such termination, the Licensee shall refrain from any further use of the
Software and destroy the original and all copies of the Software in the
possession of Licensee together with all documentation and related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without
regard to its provisions concerning conflicts of laws.
Introduction
Paradyne's 12000E IP Broadband Loop Carrier (BLC) provides a high capacity
and native IP Ethernet foundation for a variety of feature-rich multi-service access
multiplexer modules.
The 12000E BLC is engineered for efficient, high-speed IP data transport in a
compact, fully fault-tolerant chassis. It features a high capacity backplane
delivering up to 48 Gbps throughput and providing a non-blocking architecture for
even the highest bandwidth broadband access technologies, such as ADSL2+.
The 12000E BLC supports single or dual redundant uplink, management, and
switching modules. In redundant mode, both modules can be connected to the
dual backplanes with redundant modular backhaul/uplink ports to support 10/100
Ethernet, GigE (Copper or fiber), T1/E1, and dual bonded T1/E1 uplink modules.
For flexibility of installation the 12000E has removable mounting brackets that can
be placed in increments of 1.45” up to 9.28” from the front of the chassis, allowing
for multiple installation options in either 19" or 23" equipment racks.
Unpacking and Inspecting the Equipment
HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
The following components should be included in the shipping container:
1 – 12000E with 1 fan module and 12 slot covers
4 – Rubber Bumper Screws
2 – Rack Mount Brackets (either 19" or 23", as ordered)
10 – #6 Phillips Bracket Screws
8 – #10 Phillips Rack Screws
8 – #12 Phillips Rack Screws
!
4July 2005 IPD1-A2-GZ40-10
If there is visible damage, do not attempt to connect the device. Contact your sales
representative.
Installation Options
The 12000E BLC is designed for installation in a Restricted Access area where
admittance is limited to trained and authorized service personel. It may be
installed on a tabletop or in a rack.
Installation on a Tabletop
Insert the four provided rubber bumper screws into the mounting holes at the
bottom of the 12000E chassis for surface grip and airflow. Position and secure all
connecting cables such that they will not become a tripping hazard or pull loose
from the chassis. Ensure that the air supply vents around the top and bottom
edges of the chassis are not blocked.
12000E BOTTOM VIEW
RUBBER BUMPER
SCREW
Side Top
Front Rear
IPD1-A2-GZ40-10 July 2005 5
Installing in a Rack
Procedure
1. Using a Phillips screwdriver, attach the two provided rack mount brackets to
the sides of the 12000E with eight of the ten provided bracket screws. There
are seven position options for the rack brackets; position them as best suited
to the space available for your chassis on the rack being utilized.
12000E SIDE VIEW RACK MOUNT
BRACKET
Front Rear
6July 2005 IPD1-A2-GZ40-10
2. Mount the chassis onto the rack and secure the rack mount brackets to the
sides of the rack using one of the two provided sets of eight rack screws
(whichever size fits the rack being utilized).
3. Check the rack for stability, ensuring that installation of the 12000E has not
caused the rack to become top-heavy. Position and secure all connecting
cables such that they will not become a tripping hazard or pull loose from the
chassis.
Installing Your Management Module
A management module provides the functional control for the 12000E BLC; the
BLC cannot function without one. There are several different models available for
purchase. Refer to www.paradyne.com for further information, or contact your
sales representative.
Installing a Management Module
An uplink module provides the upstream network connection for the12000E BLC;
a management module cannot function without one. Depending on the
management module model that you plan to install in your 12000E, you will need
either a Media Interface Module (MIM) or an Uplink Interface Module (UIM). Only
one uplink module is required for operational purposes, however two uplink
modules may be installed, one in each port of the management module, if
redundancy is desired. Refer to your management module and/or uplink module
installation instructions for further information.
CAUTION:
If a slot cover is removed from a management module uplink port, it must be
replaced with an uplink module. DO NOT OPERATE A 12000E BLC WITH A
MANAGEMENT MODULE THAT HAS AN OPEN UPLINK PORT.
12000E FRONT VIEW
IPD1-A2-GZ40-10 July 2005 7
Procedure
1. Select a slot for installation. The 12000E is a fourteen slot chassis: slots 1–12
are reserved for interface modules and slots U1–U2 are reserved for
management modules. Although the 12000E is shipped with Port U1 open,
your management module can be installed in either Port U1 or Port U2. Only
one management module is required for operational purposes. However, two
management modules may be installed if redundancy is desired: one in Slot
U1 and one in Slot U2.
CAUTION:
If the slot cover is removed from Slot U2, it must be replaced with a
management module. DO NOT OPERATE YOUR 12000E WITH AN
EMPTY MODULE SLOT.
Management Module Slots
8July 2005 IPD1-A2-GZ40-10
2. With the management module printed circuit board (PCB) facing right and the
management module model name upright, align the upper and lower edges of
the PCB with the slot module guides.
3. Slide the management module firmly into the chassis. Tighten the fastening
screws on the management module faceplate.
MANAGEMENT
MODULE
Slot Module Guides
Fastening Screws
IPD1-A2-GZ40-10 July 2005 9
Installing Your Interface Module(s)
Interface modules provide the subscriber connections for an 12000E; up to twelve
interface modules may be installed in the 12000E (slots 1–12). There are a variety
of models available for purchase; contact your sales representative for further
information or visit www.paradyne.com for a list of available products. Any
combination of interface module models may be installed in an 12000E as long as
they are supported by the model type and version number of your management
module; refer to the Release Notes for your particular management module model
for compatibility information.
Procedure
1. Select a slot for installation. Although the 12000E is factory shipped with Slot 1
open, interface modules may be installed in any slot, 1–12.
CAUTION:
If a slot cover is removed from slot 2–12, it must be replaced with an
interface module. DO NOT OPERATE YOUR 12000E WITH AN EMPTY
MODULE SLOT.
2. With the interface module PCB facing right and the interface module model
name upright, align the upper and lower edges of the PCB with the slot
module guides.
INTERFACE
MODULE
Slot Module Guides
10 July 2005 IPD1-A2-GZ40-10
3. Slide the interface module firmly into the chassis. Tighten the fastening screws
on the interface module faceplate.
Fastening Screws
Altri manuali per 12000E
1
Indice
Altri manuali Paradyne Hardware di rete
Paradyne
Paradyne Hotwire 5216 Manuale utente
Paradyne
Paradyne FrameSaver SLV 9124 Manuale per l'uso e la cura
Paradyne
Paradyne MIM-4E1 Manuale utente
Paradyne
Paradyne JetFusion 2208 Manuale utente
Paradyne
Paradyne 3172 Manuale utente
Paradyne
Paradyne COMSPHERE 3610 Manuale
Paradyne
Paradyne COMSPHERE 3550 Series Manuale utente
Paradyne
Paradyne COMSPHERE 6700 Series Manuale utente
Paradyne
Paradyne M/HDSL Standalone Termination Unit HOTWIRE... Manuale utente
Paradyne
Paradyne COMSPHERE 3610 Manuale operativo e di manutenzione
Paradyne
Paradyne FrameSaver 9120 Manuale del proprietario
Paradyne
Paradyne BitStorm 4800 Express Manuale utente
Paradyne
Paradyne 4000E Manuale utente
Paradyne
Paradyne GranDSLAM 4200 Manuale utente
Paradyne
Paradyne MIM-2T1 Manuale utente
Paradyne
Paradyne 7610 SNMP DSU Manuale utente
Paradyne
Paradyne JetFusion 2008 Manuale utente
Paradyne
Paradyne Fan Tray 8820-S2-900 Manuale utente
Paradyne
Paradyne Hotwire 5620 RTU Manuale utente
Paradyne
Paradyne 24-Port SHDSL Mini DSLAM SMD2000-24T Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
