Paradyne Hotwire 8775 MSDSL Manuale utente

8775-A2-GZ40-00 March 1998

Hotwire8775 MSDSL Termination Unit

Installation Instructions

Document Number 8775-A2-GZ40-00

March 1998

Hotwire8775 E1 MSDSL Termination Unit

The Hotwire 8775 Termination Unit is a circuit card assembly (CCA) that contains

four E1 Multirate Symmetric Digital Subscriber Line (MSDSL) ports. When the

8775 Termination Unit is used in a Hotwire 8600 or 8800 Digital Subscriber Line

Access Multiplexer (DSLAM) chassis, it transports 2048 kbps signals over

traditional twisted-pair telephone wiring.

!HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

Package Checklist

Verify that your package contains the following:

Hotwire 8775 Circuit Card

Warranty card



Hotwire 8775 MSDSL Termination Unit User’s Guide

Document No. 8775-A2-GB20

Tool Required

Small- to medium-size flat-blade screwdriver.

496-15104

All manuals and user guides at all-guides.com

all-guides.com

2 8775-A2-GZ40-00

March 1998

Technical Specifications

Specifications Criteria*

Size Length 10 inches (25.4 cm)

Height 12.3 inches (31.1 cm)

Width 0.8 inch (2.0 cm)

Weight Approximately 1.3 lbs. (0.6 kg)

Approvals

Safety Certifications Refer to the equipment’s label for approvals on product.

Power The 8775 Termination Unit contains a DC-to-DC

converter that requires –48V power input. The –48V

power is distributed through the Hotwire DSLAM

backplane.

Maximum Power Dissipation = 19 watts

Cables and Cable Guide Part Number Description

8700-F1-500 Cable Guide for 8800 DSLAM

8700-F1-501 V.35: 100-Pin Plug to

Four MS34 Receptacles

8700-F1-502 X.21: 100-Pin Plug to

Four DB15 Receptacles

8700-F1-503 RS449: 100-Pin Plug to

Four DB37 Receptacles

8700-F1-504 EIA-530A: 100-Pin Plug to

Four DB25 Receptacles

Physical Environment

Operating temperature

Storage temperature

Relative humidity

Shock and vibration

32°to 122°F (0°to 50°C)

–4°F (–20°C) to 158°F (70°C)

5% to 85% (noncondensing)

Withstands normal shipping and handling.

* Technical specifications are subject to change without notice.

Planning the 8775 Termination Unit Installation

Review the following list to help plan for the installation.

Obtain the applicable cables; refer to

Cables You Need

Make sure the Hotwire DSLAM chassis is installed and power is supplied to

the chassis.

After the 8775 Termination Unit is installed, there are configuration

procedures that must be performed before you can begin to use the 8775

Termination Unit. Refer to the

Hotwire 8775 MSDSL Termination Unit User’s

Guide

, for more detailed configuration procedures.

All manuals and user guides at all-guides.com

8775-A2-GZ40-00 March 1998

Cables You Need

The following customer-provided cables are used with this product.

For the network connection:

Plug-ended Telco 50-pin cable for connection from the Hotwire 8600 DSLAM

LINE port or one of the Hotwire 8800 DSLAM LINES ports to the Main

Distribution Frame (MDF) or other demarcation point.

For the DTE connection, one of the following:

100-pin plug to four DB15 (X.21)

100-pin plug to four DB25 (EIA-530A)

100-pin plug to four DB37 (RS-449)

100-pin plug to four MS34 (V.35)

See

Technical Specifications

on page 2 for part numbers of the DTE cables. For

more information refer to Appendix D,

Cables and Pin Assignments

, in the User’s

Guide.

Installing DSL Cards

Use a small- to medium-size flat-blade screwdriver to install the 8775 Termination

Unit.

When using a . . . Install the 8775 Termination Unit in . . .

Hotwire 8600 DSLAM base

chassis Slot 2 or 3 (Slot 1 of the Hotwire 8600 DSLAM base

chassis must contain a Management Communications

Controller (MCC) card.)

Hotwire 8600 DSLAM

expansion chassis Slot 1, 2, or 3

Hotwire 8800 DSLAM

chassis Any one of the first 18 slots (i.e., Slot 1 through 18)

An 8775 Termination Unit can be installed, removed, and replaced from a Hotwire

DSLAM chassis without disrupting service to the other cards in the chassis.

NOTE:

When installing the 8775 Termination Unit, you need to remove the filler plate

before proceeding.

Do not discard unused filler plates. Each slot in the chassis must contain a

circuit card or a filler plate. Store all unused filler plates in a safe place. You

may need to use the filler plates to cover open slots in the chassis at a later

time.

All manuals and user guides at all-guides.com

4 8775-A2-GZ40-00

March 1998

Procedure

To install an 8775 Termination Unit:

1. Determine in which slot the 8775 Termination Unit will be installed. Verify that

cards in adjacent slots have been fastened.

2. Remove the filler plate from the installation slot.

3. Insert the 8775 Termination Unit:

— For a Hotwire 8600 DSLAM chassis – hold the 8775 Termination Unit

horizontally with component side facing up and insert it into the left and

right card guides.

INPUT

48VDC CLASS 2 OR

LIMITED PWR SOURCE

RTN48V

AAB B

LAN/WAN SLOT

POSITION

STACK ALM A

DC FUSES 5DC PWR

FAN

OUT SERIAL MCC 1

MANAGEMENT

LINE 1

98-15832

SYSTEM

OKAlrm

Test

TXRXCol

ETHERNET

M/SDSL

8775

SYSTEM

OKAlrm

Test

TXRXCol

1234

ETHERNET

DSL PORT

ESD

— For a Hotwire 8800 DSLAM chassis

–

hold the 8775 Termination Unit

vertically with component side facing right and insert it into the top and

bottom card guides.

ALARMS

Major MinorFanBA

POWER

MCC

SYSTEM

Alm

Test

ETHERNET

Coll

98-15328-0

MGT

SERIAL

MGT

10BT ALARM

SLOTS 1 - 6

SLOTS 7-12

SLOTS 13-18

LINES

-48V (A)

-48V INPUT

-48V (B)

RET (A)

RET (B)

FR GND

246810 12 14 16 18

13579

11 13 15 17

LAN/WAN SLOT 20

LAN/WAN SLOT

Slot 1

DSL

SYSTEM

Alm

Test

ETHERNET

Coll

DSL PORT

DSL Card

All manuals and user guides at all-guides.com

8775-A2-GZ40-00 March 1998

4. Slide the 8775 Termination Unit into the slot until the power and network

connectors seat firmly in the mating connectors on the backplane.

CAUTION:

Do not force the 8775 Termination Unit into the slot. If it does not seat

properly, remove the card and reinstall it. If it still does not seat

properly, call your service representative.

The 8775 Termination Unit performs a power-up self-test. All of the LEDs turn

ON and OFF briefly. When the self-test is completed successfully, the

SYSTEM OK LED will turn ON. Make sure the SYSTEM OK indicator on the

8775 Termination Unit faceplate is ON.

5. If the LED is not ON, refer to Chapter 6,

Messages and Troubleshooting

the User’s Guide.

6. Secure the 8775 Termination Unit by fastening the screws at each end of the

faceplate.

NOTE:

The 8775 Termination Unit may be replaced without system disruption (i.e.,

you can remove and reinstall a card without powering down the Hotwire

DSLAM chassis and disrupting service to the other cards). To remove an

8775 Termination Unit from the Hotwire DSLAM chassis, unfasten the screws

on both ends of the faceplate. Then push the ejector handles outward and

slide the card out.

Ensure that adjacent cards are fastened before removing a card.

When swapping the old 8775 Termination Unit with a new 8775 Termination

Unit, note that the 8600 DSLAM retains the Media Access Control (MAC)

address, also referred to as the physical address. This means that the new

8775 Termination Unit will have the same MAC address as the old one.

All manuals and user guides at all-guides.com

6 8775-A2-GZ40-00

March 1998

Cable Management

The optional Cable Guide (see

Technical Specifications

on page 2 for its part

number) connects to the front of the Hotwire 8800 DSLAM and provides strain

relief and control of the DTE cables. Install the Cable Guide before installing the

cables.

97-15777

ALARMS

Major MinorFanBA

POWER

MGT

SERIAL

MGT

10BT ALARM

SLOTS 1 - 6

SLOTS 7-12

SLOTS13-18

LINES

-48V (A)

-48V INPUT

-48V (B)

RET (A)

RET (B)

FR GND

246810 12 14 16 18

1357911 13 15 17

LAN/WAN SLOT

SLOTS13-18

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

DSLPORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703ALRM

Front Rail

Existing

Screw

Bottom Hole for

Mounting in 19"

Rack or Cabinet

Front Rail

Top Hole for

Mounting in 23"

Rack or Cabinet

Screw

Washer

and Nut

All manuals and user guides at all-guides.com

all-guides.com

8775-A2-GZ40-00 March 1998

Connecting to the DTE Equipment

Connection to the four ports of the 8775 Termination Unit is through the 100-pin

EIA-530 interface connector on its faceplate. Use one of the DTE cables listed

under

Cables You Need

on page 3.

Procedure

To connect the Hotwire 8775 Termination Unit to your DTE equipment:

1. Connect the 100-position connector of the cable to the connector on the

faceplate of the 8775 Termination Unit. Align one end of the cable connector

with the card connector, then push on the cable connector until it seats.

The end of the cable connector has a release button. To remove the

connector, press the release button and pull the connector away from the

card.

97-15726

-48V RTN F

ABAB

48VD

ETHERNET

MCC

8000

SYSTEM

OKAlrm

Test

TXRXCol

SYSTEM

OKAlrm

Test

123

G.703 ALRM

DSL PORT

LINK-UP

SYSTEM

OKAlrm

Test

123

G.703 ALRM

DSL PORT

LINK-UP

2. Feed the cable through the Cable Guide if it is in use. When all cables are

installed, anchor them with cable ties to the rack, DSLAM, or Cable Guide.

3. Connect the four terminating connectors to your DTE equipment.

All manuals and user guides at all-guides.com

8 8775-A2-GZ40-00

March 1998

Connecting to an MDF

You can connect the Hotwire DSLAM chassis containing the 8775 Termination

Unit to an MDF or other demarcation point. Do not connect it to a POTS splitter.

Procedure

To connect the Hotwire DSLAM chassis containing the 8775 Termination Unit to

an MDF:

1. Plug the Telco 50-pin cable into the appropriate LINE port on the front panel

of the chassis:

—On a Hotwire 8600 DSLAM chassis:

98-15833

INPUT

48VDC CLASS 2 OR

LIMITED PWR SOURCE

RTN48V

AAB B

LAN/WANSLOT

POSITION

STACKALM A

DC FUSES

T4A, MIN. 48V 5PWR

FAN

OUT SERIAL MCC 1

MANAGEMENT

LINE

SYSTEM

OKAlrm

Test

TXRXCol

ETHERNET

MCC

8000

SYSTEM

OKAlrm

Test

TXRXCol

1234

ETHERNET

DSL PORT

M/SDSL

8775

SYSTEM

OKAlrm

Test

TXRXCol

1234

ETHERNET

DSL PORT

M/SDSL

8775

Anchor

Mount

Telco 50-Pin

Connector

ESD

All manuals and user guides at all-guides.com

8775-A2-GZ40-00 March 1998

—On a Hotwire 8800 DSLAM chassis:

SLOTS 13-18

SLOTS 7-12

SLOTS 1-6

97-15325

Anchor Mount

Telco 50-Pin

Connector

LINES

SLOTS 1-6

LINES

Shorter

Telco

Captive Screw

2. Replace the longer Telco cable captive screw with a shorter connector

captive screw, which is provided with the Hotwire DSLAM chassis.

3. Insert a cable tie (provided with Hotwire DSLAM chassis) through the tie

mount to hold the Telco 50-pin connector in place. If more than one Telco

cable is being connected, span the two or three connectors.

4. Make sure the other end is connected to the appropriate MDF or demarcation

point.

Refer to Appendix D,

Cables and Pin Assignments

, in the User’s Guide for

pinouts.

NOTE:

If you are connecting the Telco 25-pair, 50-pin cable to an MDF, a converter

may be necessary for terminating the other end of the cable on a punchdown

block before cross-connecting to an MDF.

All manuals and user guides at all-guides.com

10 8775-A2-GZ40-00

March 1998

8775 Termination Unit LEDs

The following table describes the meaning and states of the LEDs on the 8775

Termination Unit faceplate.

Type LED LED is . . . Indicating . . .

SYSTEM OK Green

Off

Normal operation; card functioning normally.

No power to card, or card failure.

Alrm Amber

Off

Device failure, or Power-On Self Test (POST)

failure.

No alarms.

Test Amber

Amber,

flashing

Off

Loopback test or 511 test pattern in progress.

POST in progress.

No tests.

SYNC

PORT 1, 2, 3, 4 Green

Amber

Amber,

flashing

Off

Interchange circuits for the port are in the

correct state to transmit and receive data.

The port is configured to monitor DTR and/or

RTS and no monitored lead is asserted.

Data Channel Loopback (DCLB) or Data

Terminal Loopback (DTLB) is active on the

port.

The port is disabled.

DSL PORT

LINK-UP 1, 2, 3, 4 Green

Off

Amber

Amber,

flashing

DSL link is up.

DSL link is down.

DSL training in progress.

OOF condition.



*8775–A2–GZ40–00*

M/SDSL

8775

SYSTEM

OKAlrm

Test

123

G.703 ALRM

DSL PORT

LINK-UP

98-1583

All manuals and user guides at all-guides.com

Indice

Altri manuali Paradyne Hardware di rete

Paradyne

Paradyne 8540 Manuale utente

Paradyne

Paradyne MIM-4E1 Manuale utente

Paradyne

Paradyne JetFusion Integrated Access Device Manuale utente

Paradyne

Paradyne COMSPHERE 6700 Series Manuale utente

Paradyne

Paradyne Hotwire 8779 Manuale utente

Paradyne

Paradyne COMSPHERE 3800 Series Manuale di istruzioni

Paradyne

Paradyne 3163 Manuale utente

Paradyne

Paradyne Hotwire 5620 Manuale utente

Paradyne

Paradyne T1 Access Mux 916x Manuale per l'uso e la cura

Paradyne

Paradyne 12000E Manuale utente

Paradyne

Paradyne COMSPHERE 3610 Guida utente

Paradyne

Paradyne FrameSaver NP 64+ Manuale utente

Paradyne

Paradyne HotWire 7924 Manuale utente

Paradyne

Paradyne 3163 Manuale utente

Paradyne

Paradyne Hotwire 7996 Istruzioni operative originali

Paradyne

Paradyne Jetstream CPX-1000 Istruzioni operative

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Paradyne

Paradyne COMSPHERE 3550 Series Manuale utente

Paradyne

Paradyne SLV Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Paradyne

Paradyne 4300 Manuale utente

Paradyne

Paradyne Hotwire 5216 Manuale utente

Paradyne

Paradyne Hotwire 5620 Manuale utente

Paradyne

Paradyne COMSPHERE 3610 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente