Patton electronics EnviroNET 2100 Series Manuale utente

EnviroNET™ 2100 Series

Ethernet Extender

Quick Start Guide

Important

—This is a Class A device and is intended for use in an industrial environment. It is not

intended nor approved for use in a residential environment.

Important

—This device is NOT intended nor approved for connection to the PSTN. It is intended only

for connection to customer premise equipment.

Part Number: 07MEN2100-QS, Rev. B

Revised: February 29, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2EnviroNET Quick Start Guide

1.0 Before you begin

1.1 What you will need

The following components are included:

–

EnviroNET unit, including PC board, power supply, and interface board

You will need the following components (not included):

–

Flat-tip (large-bladed) screwdriver

–

Crescent® (adjustable) wrench

–

Desired length of power cable

–

Desired length of CAT5 (twisted pair) cable

–

4 bolts for mounting (A mounting kit can be purchased seperately).

1.2 Opening the case

To open the EnviroNET case:

1. Take a flat tip (large-bladed) screwdriver and insert it into the slot on a lock on the front of the case.

2. Turn the screwdriver counter-clockwise to unlock that lock.

3. Repeat Steps 1-2 for the other lock on the front of the case.

4. Lift the case door gently.

EnviroNET

™

Turn screwdriver

counter-clockwise

to open the case.

EnviroNET Quick Start Guide 3

2.0 Wiring the power

2.1 Running the power cable through the gland

To run the power cable through the gland:

1. Locate the gland that the power cable should be run through.

2. You may unscrew the gland to allow more flexibility when threading the power cable wires. To unscrew

the gland, either by hand or with a Crescent® (adjustable) wrench, turn the gland to the left until it is

loosened.

3. Carefully thread the wires through the gland from the outside into the EnviroNET.

Note The brass glands on the bottom panel of the EnviroNET can properly seal cables with an outer diameter

between 3mm and 8mm.

2.2 Connecting the power cable wires to the EnviroNET

To connect the power cable wires to the EnviroNET:

1. Run the power cable wires from outside of the EnviroNET through the unscrewed gland (on the far left) to

the inside of the unit.

2. Connect the power cable wires to the external power connection block that is labeled, E N L, as described

in table 1.

3. Be sure to leave a little slack on the wires so that they are not stressed or pulled too tightly. Also, make

sure that the power cable wires are secured tightly in the E N L block.

4. To ensure that the cables are properly secured in the gland, tighten the gland by turning the loose pieces

all the way to the right using a Crescent® (adjustable) wrench.

Table 1. Power cable wires

Designated Slot Power Wire (Color)

Earth (E) Green

Neutral (N) White

Line (L) Black

AC IN

100-240V

0.15A

50/60Hz

POWER

BLOCK

DC OUT

12V/0.42A

PWB-5002

ENL

4EnviroNET Quick Start Guide

3.0 Wiring the terminal block

3.1 Running the twisted pair wires through the gland

To run the twsited pair wires through the gland:

1. Locate the glands that the twisted pair wires should run through.

2. You may unscrew the gland to allow more flexibility when threading the wires. To unscrew the gland,

either by hand or with a Crescent® (adjustable) wrench, turn the gland to the left until it is loosened.

3. Carefully thread the wires through the gland from the outside into the EnviroNET.

Note The brass glands on the bottom panel of the EnviroNET can properly seal cables with an outer diameter

between 3mm and 8mm.

3.2 Connecting the twisted pair wires to the EnviroNET

To connect the twisted pair wires to the EnviroNET:

1. Run the twisted pair wires from outside of the EnviroNET through the unscrewed glands (on the right) to

the inside of the unit.

2. Connect the appropriate wires to the appropriate slots in the terminal block. There should be one wire per

gland. Follow the wiring diagram that is on the inside of the EnviroNET door. The terminal block is also

labeled with the numbers.

3. Be sure to leave a little slack on the wires so that they are not stressed or pulled too tightly. Also, make

sure that the twisted pair wires are secured tightly in the terminal block.

4. To ensure that the cables are properly secured in the gland, tighten the gland by turning the loose pieces

all the way to the right using a Crescent® (adjustable) wrench.

Note The black plugs for the brass glands on the bottom panel of the EnviroNET should not be removed.

EnviroNET Quick Start Guide 5

4.0 Configuring the EnviroNET

You can configure the EnviroNET via the dip switches on the PC board (except for the 2156 and 2157 models,

which require no user configuration).

4.1 EnviroNET Model 2172

EnviroNET Model 2172 uses DIP switch S2 to configure the line rate, symmetric or asymmetric, Ethernet, and

Ethernet Shutdown. Table 2 shows a summary of each switch.

Switch 1: Symmetric/Asymmetric Operation

To configure the unit for symmetric or asymmetric operation, push the first toggle switch up or down.

Refer to Table 3 for settings.

Table 2. S2 Summary

Position Description

S2-1 Symmetric/Asymmetric

S2-2 Line Rate

S2-3 Line Rate

S2-4 Ethernet configuration

S2-5 Ethernet configuration

S2-6 Ethernet configuration

S2-7 Ethernet Shutdown Enable

S2-8 Remote Configuration

Table 3. Symmetric/Asymmetric Operation

S2-1 Setting

ON Symmetric Operation

OFF Asymmetric Operation

1234

5 6 7 8

POWER ONE

BLP-30

1234

5 6 7 8

Dip Switch

6EnviroNET Quick Start Guide

Switches 2 and 3: Data Rate

Refer to table 4 for the symmetric line rate settings. (Switch 1 must be in the “On” position).

Refer to table 5 for the asymmetric line rate settings. (Switch 1 must be in the “Off” position).

Switches 4, 5 and 6: Ethernet Configuration

Refer to table 6 to configure Ethernet settings with switches 4, 5, and 6.

Switch 7: Ethernet Shutdown

To enable or disable Ethernet Shutdown, push toggle switch seven (7) up or down.

Refer to table 7 for settings.

Table 4. Symmetric CopperLink Line Rates Selection Chart

S2-2 S2-3 Symmetric Line Rate

OFF ON 50 Mbps

ON OFF 25 Mbps

OFF OFF 10 Mbps

Table 5. Asymmetric CopperLink Line Rates Selection Chart

S2-2 S2-3 Asymmetric Line Rates DS/US

ON ON 50 Mbps/2 Mbps

ON OFF 16 Mbps/2 Mbps

OFF OFF 4 Mbps/1 Mbps

Table 6. Ethernet configurations

S2-4 S2-5 S2-6 Ethernet Configurations

ON ON ON Auto-Negotiate

ON ON OFF 100Mb Full Duplex

ON OFF ON 100Mb Half Duplex

ON OFF OFF 10Mb Full Duplex

OFF ON ON 10Mb Half Duplex

Table 7. Ethernet Shutdown

S2-7 Description

ON Ethernet Shutdown Enabled

OFF Ethernet Shutdown Disabled

EnviroNET Quick Start Guide 7

Switch 8: Remote Configuration

To enable or disable Remote Configuration, push toggle switch eight (8) up or down.

Refer to table 8 for settings.

Note The S2-8 switch applies to the remote unit only. If enabled, the remote unit will follow the dip switch

configuration of the local unit. If disabled, the remote unit will use its own dip switch setting to deter-

mine its Ethernet operating mode and Ethernet Shutdown mode configuration. The S2-8 switch does not

affect the data rate. The data rate will always follow the local configuration.

4.2 EnviroNET Model 2168

EnviroNET Model 2168 uses DIP switch S1 to configure the line rate, symmetric or asymmetric, Ethernet full auto

negotiation capability or limited auto sense. Table 9 shows a summary of each switch.

Switch 1: Ethernet Auto Sense

To configure the unit for full auto sense capability or limited auto sense capability, push the first toggle switch up

or down. Full Auto sense capability consists of standard Ethernet Auto sensing (100BaseT full duplex, 100BaseT

half duplex, 10BaseT full duplex, and 10BaseT half duplex). Limited Auto sensing capability consists on only

auto sensing for 100BaseT half duplex, 10BaseT full duplex, and 10BaseT half duplex. The limited auto negotia-

tion feature is used when an Ethernet device does not comply with IEEE 802.3x (back pressure flow control) at

100M full duplex

Refer to table 10 for settings.

Table 8. Remote Configuration

S2-8 Description

ON Remote Configuration Enabled

OFF Remote Configuration Disabled

Table 9. S1 Summary

Position Description

S2-1 Ethernet Auto Sense

S2-2 Line Rate

S2-3 Line Rate

S2-4 Line Rate

S2-5 Reserved

S2-6 Reserved

S2-7 Reserved

S2-8 Reserved

Table 10. Ethernet Auto Sense Selection Chart

S1-1 Setting

OFF Full Auto Negotiation (Factory Default)

(100 Mbps, Full or Half Duplex)

(10 Mbps, Full or Half Duplex)

8EnviroNET Quick Start Guide

Switches 2, 3, and 4: Data Rate

Refer to table 11 for the symmetric line rate settings. (Switch 1 must be in the “On” position).

Refer to table 12 for the asymmetric line rate settings.(Switch 1 must be in the “Off” position).

Switches 5, 6, 7, and 8: Reserved

Switches 5, 6, 7, and 8 are reserved and should be in the ‘Off’ position.

ON Limited Auto Negotiation

(100 Mbps Half Duplex)

10 Mbps Full or Half Duplex)

Table 11. Symmetric CopperLink Line Rates Selection Chart

S1-2 S1-3 S1-4 Symmetric Line Rate

ON ON ON 6.25 Mbps

ON ON OFF 9.38 Mbps

ON OFF OFF 12.5 Mbps (Factory Default)

ON OFF ON 16.67 Mbps

Table 12. Asymmetric CopperLink Line Rates Selection Chart

S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US

OFF OFF ON 4.17 Mbps/1.56 Mbps (Mode 0)

OFF ON ON 9.38 Mbps/1.56 Mbps

OFF ON OFF 16.67 Mbps/2.34 Mbps

Table 13. Reserved for future use

S1-5 S1-6 S1-7 S1-8 Reserved

OFF OFF OFF OFF Reserved (Factory Default)

Table 10. Ethernet Auto Sense Selection Chart

S1-1 Setting

EnviroNET Quick Start Guide 9

5.0 Mounting the EnviroNET

The EnviroNET can be mounted in two ways, wall mount and pole mount.The wall mount is the typical way that

an EnviroNET can be mounted. You will need four bolts to mount the EnviroNET.

To mount the EnviroNET:

1. Make sure that the location where you chose to mount the EnviroNET is sturdy and can securely hold the

unit.

2. Be sure that the door to the EnviroNET is securely closed and locked. To lock the case, close the door and

use a flat-tip screwdriver to turn the locks to all the way to the right.

3. Mount the EnviroNET by securing the bolts through the holes on the EnviroNET to the wall panel.

Note The pole mount option is available by request. For information on how to mount the EnviroNET to a

pole, refer to the Pole Mount Kit Quick Start Guide that shipped with the pole mount kit.

6.0 Operating the EnviroNET

The EnviroNET is designed to be powered on automatically. There is no power switch. The green power LED will

light when the power is on (ET and EC models only).

To power the EnviroNET:

1. You need to wire the power cable. If you haven’t done this already, go to the section, 2.0 “Wiring the

power” on page 3.

2. After all of the cables are properly wired, close and lock the case. Plug the power cable into an electrical

outlet.

Note Once in operation, the EnviroNET will run over all temperatures without user intervention.

The EnviroNET ET and EC models have two LEDs, Power and Temperature Control Indicator.

The Power light will be on when the EnviroNET is operating normally.

The Temperature Control Indicator light will be on when the heater or fan turns on to control temperature.

Note EH models do not have a fan or heater, therefore they do not have LEDs.

7.0 Additional Information

Refer to the EnviroNET 2100 Series User Manual available online at www.patton.com/manuals/

EN2100.pdf for detailed information about:

•

Installing, configuring, operating, and troubleshooting.

•

Warranty, trademark & compliance

10 EnviroNET Quick Start Guide

A.0 Customer and Technical Support

Online support: www.patton.com

E-mail support: suppor[email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN6100-6-2

Safety Compliance:

•

UL60950-1/CSA C22.2 No. 60950-1

•

IEC/EN 60950-1

•

AS/NZS 60950-1

PSTN Regulatory Compliance:

Note This device is NOT intended nor approved for connection to the PSTN.

It is intended only for direct connection to customer premise equipment.

Altri manuali per EnviroNET 2100 Series

Indice

Altri manuali Patton electronics Estensione

Patton electronics

Patton electronics CopperLink Ethernet Extenders 2158A Manuale utente

Patton electronics

Patton electronics Industrial Ethernet Extender with LCD Interface... Manuale utente

Patton electronics

Patton electronics 2156 Manuale utente

Patton electronics

Patton electronics 2173R Manuale utente

Patton electronics

Patton electronics COPPER LINK 2174 Manuale utente

Patton electronics

Patton electronics CopperLink 2160 Series Manuale utente

Patton electronics

Patton electronics CopperLink 2160 Series Manuale utente

Patton electronics

Patton electronics 2173R Manuale utente

Patton electronics

Patton electronics EnviroNet Ethernet Extenders Manuale utente

Patton electronics

Patton electronics 1068 Manuale utente

Patton electronics

Patton electronics CopperLINK 2173 Manuale utente

Patton electronics

Patton electronics 1058 Manuale utente

Patton electronics

Patton electronics Industrial Ethernet Extender with LCD Interface... Manuale di istruzioni

Patton electronics

Patton electronics CopperLINK 2172A Manuale utente

Patton electronics

Patton electronics CopperLink 2172R Manuale utente

Patton electronics

Patton electronics CopperLink 2158 Manuale utente

Patton electronics

Patton electronics EnviroNET EHA2168 Manuale utente

Patton electronics

Patton electronics CopperLink 2160 Series Manuale utente

Patton electronics

Patton electronics CopperLink 2158 Manuale utente

Patton electronics

Patton electronics 2100 Series Manuale utente

Patton electronics

Patton electronics CopperLINK 2172 Manuale utente

Patton electronics

Patton electronics CopperLINK 2173 Manuale utente

Patton electronics

Patton electronics CopperLINK 2168B Manuale utente

Patton electronics

Patton electronics COPPERLINK 2151 Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente