Patton electronics 1206P Manuale utente
MODEM ELIMINATOR, X.21
1206P
(CTS ME-X.21)
INSTALLATION AND OPERATIONS MANUAL
Doc #: 118001UA
Part #: 07M1206P-A
Copyright© 2000 Patton Electronics Co., All Rights Reserved
An ISO-9001
CertifiedCompany
1206P INSTALLATION AND OPERATIONS MANUAL
118001UA
PATTONELECTRONICSCO.
i
COPYRIGHTNOTICE
Copyright©2000PattonElectronicsCo.,AllRightsReserved.
PROPRIETARY NOTICE
The information contained herein is proprietary and confidential to Patton Electronics
Co. Any reproduction or redistribution of this publication, in whole or in part, is
expressly prohibited unless written authorization is given by Patton Electronics Co.
WARRANTY NOTICE
WARRANTIES: Patton Electronics Co. (hereafter referred to as Patton) warrants
that its equipment is free from any defects in materials and workmanship. The
warranty period shall be two years from the date of shipment of equipment.
Patton’s sole obligation under its warranty is limited to the repair or replacement of
the defective equipment, provided it is returned to Patton, transportation prepaid,
within a reasonable period. This warranty will not extend to equipment subjected to
accident, misuse, alterations or repair not made by Patton or authorized by Patton
in writing.
PUBLICATION NOTICE
This manual has been compiled and checked for accuracy. The information in this
manual does not constitute a warranty of performance. Patton reserves the right to
revise this publication and make changes from time to time in the content thereof.
Patton assumes no liability for losses incurred as a result of out-of-date or incorrect
information contained in this manual.
INSTALLATION AND OPERATIONS MANUAL1206P
118001UA
PATTONELECTRONICSCO.
ii
EMISSION REQUIREMENTS
FCC CLASS A
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expence.
CANADIAN EMISSIONS
This digital apparatus does not exceed the Class A limits for noise emmissions from
a digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le present appareil numerique n’emet pas de bruits redioelectriques depassant les
limites applicables aux appareils numeriques de la Class A prescites dans le
Reglement sur le brouillage redioelectrique edicte par le ministere des
Communications du Canada.
1206P INSTALLATION AND OPERATIONS MANUAL
118001UA
PATTONELECTRONICSCO.
iii
TABLE OF CONTENTS
CHAPTER 1 - OPERATION
Clocking ........................................................................................................................... 1-1
DelayingINDICATE .......................................................................................................... 1-1
Power .............................................................................................................................. 1-1
Approvals......................................................................................................................... 1-2
Available Options............................................................................................................. 1-2
CHAPTER 2 - SETUP AND INSTALLATION
Power Connection .......................................................................................................... 2-1
Factory Configuration Switch Settings.......................................................................... 2-1
Disassembly .................................................................................................................... 2-2
Installation ....................................................................................................................... 2-2
Equipment Grounding (JP4)........................................................................................... 2-2
IND Delay, Port 1 (SW2-1,2)........................................................................................ 2-2
IND Delay, Port 2 (SW2-4,5)........................................................................................ 2-2
Internal Baud Rate Selection (SW1-1,2,3,4) .............................................................. 2-3
High Speed Option Rates (JP7,JP8,JP9,JP10).......................................................... 2-3
Factory Test Jumpers (JP1).......................................................................................... 2-4
APPENDIX
DB-15 Connector Pins Used ......................................................................................... A-1
Signal Flow Diagram....................................................................................................... A-1
Strapping Guide .............................................................................................................. A-2
1206P INSTALLATION AND OPERATIONS MANUAL
118001UA
PATTONELECTRONICSCO.
1-1 OPERATION
CHAPTER 1 - OPERATION
The 1206P (CTS ME-X.21) is a cost effective solution for interconnection of X.21
terminal devices located in proximity of each other. The use of two modems is
eliminated with a resulting cost savings to the user. The 1206P (CTS ME-X.21)
complies with the CCITT V.11 balanced interface specification. Two 15 pin DB-15
connectors are provided to interface to the X.21 terminals.
Clocking
Clockingatratesupto768Kbpswiththelowspeedversionandupto2.048MbpswithHigh
SpeedOptionare providedbytheinternalbaudrategenerator. Thegeneratorwillprovide
clocksforbothterminalandinsurethedataissynchronizedwiththeSClockinboth
directions.
Delaying INDICATE
Control(C)isloopedback toIndicate(I)oneach Port. ToallowterminalsrequiringI delayto
functionproperly,selectable delaysofConstant,0mS,8mS and50mSofCto Idelayis
provided. EachPortisindividuallyconfiguredforIdelay.
Power
110or220 Volt operation is provided by aconvenientswitchlocated on the rear panel of the
1206P (CTS ME-X.21). Simply install the proper fuses (110VAC - .16ASB, 250V or 220VAC
-.8ASB,250V)andpowerplugforthecountry ofuse andselect theproper linevoltage and
theunitisreadyforoperation.
INTERNATIONAL
SERIES
1206P
PWR TRC I S
INSTALLATION AND OPERATIONS MANUAL1206P
118001UA
PATTONELECTRONICSCO.
1-2
OPERATION
Approvals
Safetyapprovals forUL,CSA & TÜVhave beengrantedallowing theModemEliminator to be
usedvirtuallyanywhereintheworld. FCCPart15classAemissionsapprovalsinsurethe
ModemEliminatorwillnotinterferewithanyoftheotherequipmentinyourdatacenter.
CENOTICE: The CE symbolonyour Patton Electronicsequipmentindicates that it isin
compliancewiththe Electromagnetic Compatibility (EMC)directiveand the Low Voltage
Directive (LVD) of the Union European (EU). A Certificate of Compliance is available by
contactingTechnical Support.
AvailableOptions
1206P(CTSME-X.21)isavailableinbothstand-alonesubsetorrack-mountableversions
(1206PRC). Variousconfigurationoftheinterfacearealsoavailablefromthefactory. The
1206PRC fits into the Model 1010R16 16 Card Rack Assembly.
1206P INSTALLATION AND OPERATIONS MANUAL
118001UA
PATTONELECTRONICSCO.
2-1 SETUP & INSTALLATION
Caution, Disconnect the POWER Before Removing The Cover
Vorsicht, Befor Deckung Abnehmen Mach Strom Zu.
Power Connection
Before connecting the 1206P (CTS ME-X.21) to a AC power source the top cover must be
installedand secured with thesupplied#8-32 screws. The unitissupplied with a110/220VA
voltageswitch,turntheswitchwithacoinorscrewdrivertotheappropriatevoltageforyour
country. EXAMPLE:IntheUnitedStatesof
America; set to 110VA. The unit is supplied
withaIECpowerconnectornexttothe
voltageselectswitch,plugthepowercord
intotheconnectoruntilitisfirmlyseated.
Youmaynowconnectthepowercordinto
yourACoutlet.
Factory Configuration Switch Settings
The1206P (CTSME-X.21)is configuredpriorto shipmentwiththe switchessetto the
followingdefaultpositions:
Switch 1 - 2, 3, 5 and 6 to OFF, 1 and 4 to ON.
Baud Rate = 64Kbps
Switch 2 - 1, 3, 4 and 6 to OFF, 2, and 5 to ON.
Port 1 IND Delay = 0
Port 2 IND Delay = 0
JP1 - JP3 always connected
JP4 - Open
HS Option
JP7 - Open
JP8 - Open
JP9 - Open
JP10 - Open
If the system application requires one of more of the default settings to be
changed, it will be necessary to remove the top cover of the enclosure to access
and change the DIP switches or Jumpers located on the printed circuit board.
CHAPTER 2 - SETUP AND INSTALLATION
CAUTION
: FOR CONTINUED PROTECTION AGAINST RISK
FIRE, REPLACE ONLY
WITH SAME TYPE
AND RATING FUSE.
110 / 220VA Switch
Fuse Drawer
PORT 1
IEC PowerConnector
110
220
100-120V
0.16ASB,250V
TO.16A,250V
200-240V
0.08ASB,250V
TO 0.08A,250V
*
* Switch fuse for 100-120V (.16ASB, 250V) or 200-240V
(.8ASB, 250V) as noted on rear of unit.
INSTALLATION AND OPERATIONS MANUAL1206P
118001UA
PATTONELECTRONICSCO.
SETUP & INSTALLATION 2-2
Disassembly
Removethetopcoverbyunscrewingthephillipsheadscrewslocatedontheleftandright
sidesof the 1206P (CTSME-X.21). Theconfiguration switches andJumpersare located on
thePCB as indicatedonthe strapping guideinthe Appendix ofthismanual. After the switch
selectionactivityiscompleted,
re-install the top cover BEFORE connecting to an AC
powersource.
Installation
Selectanappropriatelocation accessible to and within six feet ofanACpoweroutlet. The
outletmusthaveagroundpinreceptacleforproductwarranty.
"StraightThrough"
shielded
cables,terminatedinmale X.21(DB-15)connectorsshouldbeusedtoconnectthetwo
terminalsto the1206P (CTSME-X.21). Set theswitchesandJumpersto matchthe required
configurationusingthedescriptionsinthischapterandthestrappingguideintheappendix.
Equipment Grounding (JP4)
JP4providesforgroundinginterconnectioninthosesystemsrequiringaconnectionbetween
(FrameGround)and(SignalGround). ConnectONLYifrequired.
IND Delay, Port 1 (SW2-1,2)
SW2 position 1 and 2 selects C to I delay for the terminal connected to PORT 1. C (pins 3,10)
fromPORT1isloopedbacktoI(pins5,12)throughthedelaycircuitry.
SW2-1 SW2-2 DELAY
ON ON Const
OFF ON 0mS
ON OFF 8mS
OFF OFF 50mS
IND Delay, Port 2 (SW2-4,5)
SW2 position 4 and 5 selects C to I delay for the terminal connected to PORT 2. C (pins 3,10)
fromPORT2isloopedbacktoI(pins5,12)throughthedelaycircuitry.
SW2-4 SW2-5 DELAY
ON ON Const
OFF ON 0mS
ON OFF 8mS
OFF OFF 50mS
Internal Baud Rate Selection (SW1-1,2,3,4)
1206P INSTALLATION AND OPERATIONS MANUAL
118001UA
PATTONELECTRONICSCO.
2-3 SETUP & INSTALLATION
Selectionofinternal rates is provided byconfigurationof SW1 positions 1 through4and JP7
throughJP10iftheHighSpeedOptionhasbeeninstalledbythefactory. Thefollowingtable
showstheratesavailable:
SW1-1 SW1-2 SW1-3 SW1-4 RATE
ON ON ON ON HS Opt
OFF ON ON ON 768K
ON OFF ON ON 384K
OFF OFF ON ON 192K
ON ON OFF ON 128K
OFF ON OFF ON 72K
ON OFF OFF ON 64K*
OFF OFF OFF ON 57.6K
ON ON ON OFF 56K
OFF ON ON OFF 48K
ON OFF ON OFF 38.4K
OFF OFF ON OFF 28.8K
ON ON OFF OFF 19.2K
OFF ON OFF OFF 14.4K
ON OFF OFF OFF 9.6K
OFF OFF OFF OFF 4.8K
High Speed Option Rates (JP7,JP8,JP9,JP10)
IfthehighspeedoptionisinstalledthefollowingratescanbeutilizedbysettingSW1positions
1through 4to ON:
JP10 Installed JP7, JP8 & JP9 Removed - 256K
JP9 Installed JP7, JP8 & JP10 Removed - 512K
JP8 Installed JP7, JP9 & JP10 Removed - 1.024M
JP7 Installed JP8, JP9 & JP10 Removed - 2.048M
Factory Test Jumper (JP1)
INSTALLATION AND OPERATIONS MANUAL1206P
118001UA
PATTONELECTRONICSCO.
SETUP & INSTALLATION 2-4
ThefactorytestjumpermustbeinstalledfortheModemeliminatortoproperlyfunction. Insure
thisjumperisinstalledpriortooperationoftheunit.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Patton electronics Modem
Patton electronics
Patton electronics 1110 Manuale utente
Patton electronics
Patton electronics 1070RC Manuale utente
Patton electronics
Patton electronics ParaLink 1225 Manuale utente
Patton electronics
Patton electronics 1090 Manuale utente
Patton electronics
Patton electronics 1058 Manuale utente
Patton electronics
Patton electronics 1045 Manuale utente
Patton electronics
Patton electronics 3012/V24, 3014/V24, 3018/V24 Manuale utente
Patton electronics
Patton electronics 1200P Manuale utente
Patton electronics
Patton electronics 1006 Manuale utente
Patton electronics
Patton electronics 1088/K Manuale utente
Patton electronics
Patton electronics 1068 Manuale utente
Patton electronics
Patton electronics 1180 Manuale utente
Patton electronics
Patton electronics 1089/C Manuale utente
Patton electronics
Patton electronics 1205P Manuale utente
Patton electronics
Patton electronics 1010A Manuale utente
Patton electronics
Patton electronics 1205 Manuale utente
Patton electronics
Patton electronics Model 1065 Manuale utente
Patton electronics
Patton electronics 1058 Manuale utente
Patton electronics
Patton electronics 1092 Manuale utente
Patton electronics
Patton electronics 1186 Manuale utente
