Patton SmartNode 10100 Series Manuale utente

SmartNode™ 10100 Series

TDM+VoIP Smart Media Gateway

Quick Start Guide

This is a Class A device and is not intended for use in a residential environment.

Part Number: 07MSN10100-QS, Rev. A

Revised: April 9, 2014

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: suppor[email protected]om

WWW: www.patton.com

2 SmartNode 10100 Series Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

WARNING

SmartNode 10100 Series Quick Start Guide 3

1.0 Before you Begin

In the box, you will find:

•One SmartNode 10100

•One set of mounting brackets with screws

•One DB-9 to RJ-45 adapter

•Three CAT5 Ethernet straight cables (male-male), three meters in length

•One warranty sheet

•One packing slip

•One SmartNode 10100 Series Quick Start Guide

•One SmartNode 10100 Important Notice sheet with unique information for your specific unit

To install the SN10100, you will need (not included):

•Two AC power cords

•19” equipment rack

Note Two DC power cable are included with DC units.

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin

contact. Connect the clip to an unpainted surface of the chassis frame

to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

CAUTION

4 SmartNode 10100 Series Quick Start Guide

2.0 Installing the rack hardware

1. Connect the Ethernet port to your management network.

Figure 1. Installing the SN10100

3.0 Connecting to the VoIP Network

1. Connect a CAT5 Ethernet cable to VoIP0 at the rear of the SN10100. Connect the other end of the same

CAT5 cable to the Gigabit Ethernet switch.

2. If your system employs a second Gigabit Ethernet switch for redundancy, connect a second CAT5 Ethernet

cable to VoIP1and the other end to the second Gigabit Ethernet switch.

Figure 2. Connecting the VoIP ports

SmartNode

™

Console

Ethernet

Power

TDM+VoIP Smart Media Gateway

Management

Attach the SmartNode

to the equipment rack

Attach the bracket

to the SmartNode

SmartNode 10100 Series Quick Start Guide 5

4.0 Connecting to the PSTN Network

A SN10100 with 8 RJ48C type ports enables the connection to T1/E1 lines.

Note T1/E1 ports are activated by software license; the number of active ports

depends on the licenses purchased.

1. Start with port 0, located at the top and leftmost position. Connect one cable between this port and the

T1/E1 line.

2. Repeat step 1, using the next available port.

Figure 3. Port Interface to the PSTN

5.0 Connecting to the Power source

5.1 AC Power

The SN10100 connects to two independent power sources. If only one power source is used, press the green but-

ton at the rear of the unit to disable the audible alarm.

1. Connect an AC power cable between the AC connector of the SN10100 and an AC supply.

6 SmartNode 10100 Series Quick Start Guide

2. Power up the SN10100 by turning on its power switch(es).

Figure 4. AC Power Connection(s)

5.2 DC Power

The SN10100 DC models are furnished with one or two DC power connection ports and is supplied with two DC

power cables.

1. Connect one DC cable to the DC outlet at the rear of the SN10100

2. Connect one lead of the DC power cable to the positive terminal of the DC power source.

3. Connect the other lead of the DC power cable to the negative side of the DC power source.

4. Repeat steps 1-3 for the second DC power source, if necessary.

Figure 5. DC Power Connection(s)

SmartNode 10100 Series Quick Start Guide 7

6.0 Connecting to the Control host

1. Connect to the Control host through the Console Serial port (see 6.1 “Connecting the Console Serial port”)

OR the Ethernet management interface (see 6.2 “Connecting the Ethernet management interface”).

The IP address of the management port is 192.168.200.10/24. If it is not possible to connect to the

management port via IP, use the serial cable to connect to the SmartNode Control host for the first time.

2. Default HOSTNAME is the Control host serial number, which can be found in the “Important Notice” sheet

included with your shipment.

3. Refer to the “Important Notice” sheet for the username and password to log onto the Control host. Navi-

gate to: HTTP://HOSTNAME:12358, to configure the SmartNode unit. (username/password: root/root)

6.1 Connecting the Console Serial port

1. Connect the supplied CAT5 RJ-45 (male-male) cable between the COM port of your computer and the

serial port (labeled 1010) of the SN10100.

2. If your computer’s serial port features a DB9 connector, use the DB9 to RJ-45 adapter supplied with your

SN10100. If your computer’s serial port features a USB connector, you will need to provide a USB to DB9

adapter.

Figure 6. Computer to the Console Serial port

6.2 Connecting the Ethernet management interface

1. Connect the supplied CAT5 Ethernet cable to the management port labeled Ethernet on the front of the

SN10100.

8 SmartNode 10100 Series Quick Start Guide

2. Login to the SmartNode using the specific credentials included on the “Important Notice” sheet that

shipped with your unit. The management port is configured with a static Class C IP address by default.

Figure 7. Conneting the management interface

7.0 Configuring the SmartNode

Access the SmartNode through the Console Management port, or through the Ethernet management port. Refer

to the following sections for more information:

•7.1 “Accessing the SmartNode via the Console Serial port”

•7.2 “Accessing the SmartNode via the Ethernet management port”

7.1 Accessing the SmartNode via the Console Serial port

Logging into the SmartNode Console

1. To physically connect the Consol Serial port, follow the instructions in section 6.1, “Connecting the Console

Serial port” on page 7.

2. To communicate with the SN10100 through the consol port, you must first configure a terminal emulator

or console application (such as HyperTerminal or Putty) in order to configure initial settings. Configure

the terminal emulator with the following settings:

3. Login to the console using the specific credentials included on the “Important Notice” sheet that shipped

with your unit. (If you do not have the “Important Notice” sheet, contact suppor[email protected]om.) The fac-

tory default configuration for the Ethernet Interface IP address is 192.168.200.10/24.

Baud rate Data rate Parity Stop bits Flow control

9600 8 bits None 1 None

SmartNode 10100 Series Quick Start Guide 9

7.2 Accessing the SmartNode via the Ethernet manage-

ment port

Logging into the SmartNode via SSH

1. To physically connect the Ethernet management port, follow the instructions in section 6.2, “Connecting

the Ethernet management interface” on page 7.

2. To access the SN10100, you must use an SSH connection. The password is set at the factory and is indi-

cated on the “Important Notice” sheet included with your unit. (If you do not have the “Important

Notice” sheet, contact support@patton.com.)

3. The factory default configuration for the Managmeent Ethernet Interface is a Static IP address:

192.168.200.10/24.

Preparing for Web Management

After logging into the SN10100 via the console port or SSH, a control menu displays. This menu allows you to

complete simple tasks like setting the time zone and configuring the management IP Address, and more compli-

cated tasks like advanced debugging.

For debugging assistance, contact Patton’s Support team at support@patton.com. Once your IP Address and

Time Zone are set, there are no more configuration steps in the CLI and you may proceed to the web manage-

ment page.

8.0 Logging into the Web Interface

This section describes how to login and navigate the SmartNode 10100 Web Portal.

The first step involved in initially configuring any Smart Media system involves logging on to the Web Portal. This

can be divided into two distinct tasks: connecting to the web server and logging on to the Web Portal. For estab-

lishing IP connectivity refer to section 7.2, “Accessing the SmartNode via the Ethernet management port” on

page 9.

8.1 Connecting to the web server

Using a web browser, connect to the Web Portal by typing the following in you address bar:

–http://[DEVICE HOST NAME]:12358

or, alternately,

–http://[DEVICE IP ADDRESS]:12358

8.2 Logging onto the Web Portal

In order to log onto the Web Portal configuration tool, enter the root user ID and password. The default values

for these parameters are:

–User ID: root

10 SmartNode 10100 Series Quick Start Guide

–Default password: root

9.0 Additional Information

Refer to the following manuals—available online at www.patton.com/manuals—for detailed information

about installing, configuring and operating the SN10100 models, along with warranty, trademark and compli-

ance information.

•SmartNode 10100 Series User Manual —www.patton.com/manuals/SN10100.pdf

•Smart Media System Software Configuration Guide —www.patton.com/manuals/SmartMedia-scg.pdf

A.0 Compliance Information

A.1 Compliance

EMC

•FCC Part 15, Class A

•EN55022, Class A

•EN ETSI 300 386 V1.3.3

Low-Voltage Directive (Safety)

•UL 60950-1/CSA C22.2 No. 60950-1

•IEC/EN60950-1

A.2 Radio and TV Interference

This device generates and uses radio frequency energy, and if not installed and used properly—that is, in strict

accordance with the manufacturer’s instructions—may cause interference to radio and television reception. This

equipment has been tested and found to comply with the limits for a Class A computing device in accordance with

specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from

such interference in a commercial installation. However, there is no guarantee that interference will not occur in

a particular installation. If the equipment does cause interference to radio or television reception, which can be

determined by disconnecting the unit, try to correct the interference by one or more of the following measures:

moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging

the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on dif-

ferent branches).

Altri manuali per SmartNode 10100 Series

Indice

Altri manuali Patton Portale

Patton

Patton 07MSNOGA-DS5 Manuale utente

Patton

Patton SmartNode 4300 Manuale utente

Patton

Patton SmartNode 4970 Series Manuale utente

Patton

Patton SmartNode 4900 Manuale utente

Patton

Patton SmartNode 4120 Manuale utente

Patton

Patton SmartNode 10100 Series Manuale utente

Patton

Patton SmartNode SN5550 Manuale utente

Patton

Patton SN4112 Manuale utente

Patton

Patton 1000 Manuale utente

Patton

Patton SmartNode 5540 Series Manuale utente

Patton

Patton SmartNode 4970 Series Manuale utente

Patton

Patton SmartNode SN4170 Manuale utente

Patton

Patton SmartNode 4131 Manuale utente

Patton

Patton FiberPlex FPX6000 Series Manuale utente

Patton

Patton SmartNode 4940 Series Manuale utente

Patton

Patton SmartNode 4740 Series Manuale utente

Patton

Patton SmartNode 5541 Series Manuale utente

Patton

Patton SmartNode 4554 Manuale utente

Patton

Patton Smart Node 4120 Manuale utente

Patton

Patton SmartNode 5540E Series Manuale utente

Patton

Patton SmartNode 4520 Series Manuale utente

Patton

Patton FiberPlex FPX6000 Series Manuale utente

Patton

Patton SmartNode 4970A Series Manuale utente

Patton

Patton SmartNode 4554 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente