PCB Piezotronics 691B42 Manuale utente

Model 691B42

Switch Box

Installation and Operating Manual

For assistance with the operation of this product,

contact PCB Piezotronics, Inc.

Toll-free: 800-959-4464

24-hour SensorLine: 716-684-0001

Fax: 716-684-3823

E-mail: [email protected]

Web: www.imi-sensors.com

The information contained in this document supersedes all similar information that

may be found elsewhere in this manual.

Service –Due to the sophisticated

nature of the sensors and associated

instrumentation provided by PCB

Piezotronics, user servicing or repair is

not recommended and, if attempted,

may void the factory warranty. Routine

maintenance, such as the cleaning of

electrical connectors, housings, and

mounting surfaces with solutions and

techniques that will not harm the

physical material of construction, is

acceptable. Caution should be observed

to ensure that liquids are not permitted

to migrate into devices that are not

hermetically sealed. Such devices

should only be wiped with a dampened

cloth and never submerged or have

liquids poured upon them.

Repair –In the event that equipment

becomes damaged or ceases to

operate, arrangements should be made

to return the equipment to PCB

Piezotronics for repair. User servicing or

repair is not recommended and, if

attempted, may void the factory

warranty.

Calibration –Routine calibration of

sensors and associated instrumentation

is recommended as this helps build

confidence in measurement accuracy

and acquired data. Equipment

calibration cycles are typically

established by the users own quality

regimen. When in doubt about a

calibration cycle, a good “rule of thumb”

is to recalibrate on an annual basis. It is

also good practice to recalibrate after

exposure to any severe temperature

extreme, shock, load, or other

environmental influence, or prior to any

critical test.

PCB Piezotronics maintains an ISO-

9001 certified metrology laboratory and

offers calibration services, which are

accredited by A2LA to ISO/IEC 17025,

with full traceability to SI through

N.I.S.T. In addition to the normally

supplied calibration, special testing is

also available, such as: sensitivity at

elevated or cryogenic temperatures,

phase response, extended high or low

frequency response, extended range,

leak testing, hydrostatic pressure

testing, and others. For information on

standard recalibration services or

special testing, contact your local PCB

Piezotronics distributor, sales

representative, or factory customer

service representative.

Returning Equipment –Following

these procedures will ensure that your

returned materials are handled in the

most expedient manner. Before

returning any equipment to PCB

Piezotronics, contact your local

distributor, sales representative, or

factory customer service representative

to obtain a Return Warranty, Service,

Repair, and Return Policies and

Instructions Materials Authorization

(RMA) Number. This RMA number

should be clearly marked on the outside

of all package(s) and on the packing

Service, Repair, and Return

Policies and Instructions

list(s) accompanying the shipment. A

detailed account of the nature of the

problem(s) being experienced with the

equipment should also be included

inside the package(s) containing any

returned materials.

A Purchase Order, included with the

returned materials, will expedite the

turn-around of serviced equipment. It is

recommended to include authorization

on the Purchase Order for PCB to

proceed with any repairs, as long as

they do not exceed 50% of the

replacement cost of the returned

item(s). PCB will provide a price

quotation or replacement

recommendation for any item whose

repair costs would exceed 50% of

replacement cost, or any item that is not

economically feasible to repair. For

routine calibration services, the

Purchase Order should include

authorization to proceed and return at

current pricing, which can be obtained

from a factory customer service

representative.

Contact Information –International

customers should direct all inquiries to

their local distributor or sales office. A

complete list of distributors and offices

can be found at www.pcb.com.

Customers within the United States may

contact their local sales representative

or a factory customer service

representative. A complete list of sales

representatives can be found at

www.pcb.com. Toll-free telephone

numbers for a factory customer service

representative, in the division

responsible for this product, can be

found on the title page at the front of this

manual. Our ship to address and

general contact numbers are:

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLineSM: (716) 684-0001

Website: www.pcb.com

E-mail: [email protected]

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

DOCUMENT NUMBER: 21354

DOCUMENT REVISION: D

ECN: 46162

Component Name

Hazardous Substances

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl

Ethers (PBDE)

Housing

PCB Board

Electrical

Connectors

Piezoelectric

Crystals

Epoxy

Teflon

Electronics

Thick Film

Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above

the limit requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

The Models 691B41 & 691B42 Vibration Switch Boxes

Operating Guide with Enclosed Warranty Information

3425 Walden Avenue, Depew, New York 14043-2495

Phone (716) 684-0003

Fax (716) 684-3823

Toll Free Line 1-800-959-4IMI

SENSORS AND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

MANUAL NUMBER: 18420

MANUAL REVISION: A

ECO: 46486

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

PAGE

SENSORS AND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

table of contents

Introduction....................................................................................................................... page 3

Installation........................................................................................................................ page 3

Terminal Strip Wiring........................................................................................................ page 4

Grounding the Enclosure.................................................................................................. page 5

figure 1 –vibration switch box..................................................................................... page 5

Calibration........................................................................................................................ page 5

ESD Warning Information................................................................................................. page 6

warranty/servicing

Warranty, Service & Return Procedure ............................................................................ page 7

Customer Service............................................................................................................. page 8

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

PAGE

SENSORS AND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

introduction

The Models 691B41 and 691B42 are vibration switch boxes that provide terminal strip input with the convenience

of BNC outputs. They are used in conjunction with commercially available data collectors and analyzers. They

provide inputs and switched outputs for vibration sensors with built in temperature sensors. A few specifications

are listed below for easy reference:

Model Number Number of Channels

691B41..............................................................................................................................................6

691B42............................................................................................................................................12

Input Connectors .......................................................................................4-Socket Terminal Strip

Output Connector: Vibration.............................................................................................BNC Jack

Output Connector: Temperature.......................................................................................BNC Jack

Enclosure Type........................................................................................................NEMA 4X (IP67)

Size.............................................................................................8 x 6 x 4 in [203 x 152 x 102 mm]

installation

Establish an easily accessible location for installation and keep in mind that the cabling will be coming from the

bottom panel of the enclosure. Make the necessary holes in the panel for the vibration sensor cabling. Use the

supplied mounting feet to install the enclosure.

NOTE: Be very careful when punching and/or drilling the enclosure as to not damage the internal metal, terminal

strips and printed circuit boards.

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

PAGE

SENSORS AND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

terminal strip wiring

Positive Input

Connect the sensor’s positive input

Negative Input

Connect the sensor’s negative input

Shield

Connect the sensor’s shield; if applicable

TEMP

TEMP –Temperature Sensor Input

If the vibration sensors have a built-in temperature

sensor, connect the wire to this terminal strip input.

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

PAGE

SENSORS AND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

Grounding the enclosure

The enclosure is made of a non-conductive material. To ground the internal shielding system (ground planes on

PC Board, mounting panel and switch enclosure), an external earth ground wire must be connected. To do this,

the bottom, left, inner-mounting bolt has a double nut and spade lug included. Unscrew the nut, insert ground

wire into spade lug and screw nut tightly down again. This will earth ground all the shields and the inner metal

pieces. This will not ground the (-) input of the vibration sensors, since they are isolated from the shield.

figure 1 –vibration switch box

calibration

The 691B41 and 691B42 do not need any calibration since they are only switch boxes. If there are any questions

concerning the products, please contact the factory.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PCB Piezotronics Interruttore

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691C42T Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS EX686B71 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691B43 Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691B44 Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors 691A80 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691B47 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685B-Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS EX686B11 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685A08 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS Y685B0001A13 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685B0401C14 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685B0001D30 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors 685B Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors 686B61 Manuale utente

PCB Piezotronics

PCB Piezotronics 010D10 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685B1001A31 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS Y685A19 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691B46 Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685B1001A10 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors 686B1 0012 Series Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 685A19 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS SS691C42 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS 686B02 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS EX686B01 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente