peerless-AV LCH-100 Guida
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 09-30-02 SHEET #: 090-9085-6 07-23-13
Installation and Assembly - Monitor Desktop Stand Models: LCH-100
LCH-100
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
NOTE: You may not use all hardware provided.
NOTE: Some parts may not appear exactly as illustrated.
G
FH
E
K
MN
IJ
A
L
B
LOCK BALL
C
IMPORTANT! The product is made to support screens with a Vesa compliant hole pattern.
For safe mounting, mounting screws must turn at least three times in the screen inserts.
SPRING LOADED PRODUCT
• Only release lock ball when screen is
installed. Do not place chin or object
above pole when releasing lock ball.
WARNING
D
LCH-100
Description Qty. Part #
A
telescopic pedestal 1 091-1088
Bpivot head 1 091-1090
Cmounting base 1 091-1089
Dadapter plate 1 095-1100
EM4 x 8mm countersink screw 4520-1795
FM4 x 10mm phillips screw 4520-1796
Gwood screw #14 x 1 4510-9159
Hhex bolt 1 -
Ihex nut 1 -
JM4 x 0.7mm nut 4 530-1082
Kpressure plate 1 -
Lnylon washer 1 540-1636
M4mm allen wrench 2 560-0072
N3mm allen wrench 1 560-0073
Parts List
MAX Load Capacity:
25 lb (11.4KG)
ISSUED: 09-30-02 SHEET #: 090-9085-6 07-23-13
2 of 5
G
DESKTOP
C
C
DESKTOP
H
I
K
Insert telescopic pedestal (A) into mounting base (C).
Tighten set screws where shown with 3 mm allen wrench (N).
Mark hole on desktop for positioning mount.
Drill one 1/2" dia. hole through desktop. Attach
mounting base (C) to desktop using hex bolt (H),
pressure plate (K), and hex nut (I). Tighten nut
using proper sized wrench.
Important! Mount is to be installed onto desktops
3/4" to 1-5/8" thick only! For thicker mounting
surfaces, you may have to provide your own
hardware.
There are two methods of installation. Follow step 1 for installation using hex bolt and pressure plate or
step 2 using four wood screws. Use four holes on mounting base (C) to mark holes
on desktop for positioning mount. Drill four 3/16"
dia. holes through desktop. Attach mounting base
(C) to desktop using four wood screws (G).
SET SCREWS
A
C
• Mount must be installed on wood and/or wood composition surfaces of at least 3/4" thick. However, the installer
must ensure that the mounting surface will safely hold the combined weight of the mount and the screen. See other
mounting requirements below.
CAUTION
ISSUED: 09-30-02 SHEET #: 090-9085-6 07-23-13
3 of 5
F
B
GENERIC LCD SCREEN
To install to a VESA 75 mm standard LCD monitor,
attach pivot head (B) to back of LCD monitor using four
M4 x 10 mm phillips screws (F) as shown.
Skip to step 6.
F
B
D
B
J
E
GENERIC LCD SCREEN
To install to a VESA 100 mm standard LCD monitor, attach
adapter plate (D) to pivot head (B) using four M4 x 8 mm
phillips screws (E) and four M4 x 0.7mm nuts (J) as shown in
detail 1. Attach pivot head (B) to back of LCD monitor using
four M4 x 10 mm phillips screws (F) as shown in detail 2.
DETAIL 1 DETAIL 2
ISSUED: 09-30-02 SHEET #: 090-9085-6 07-23-13
4 of 5
Place nylon washer (L) and pivot head (B) on top pin
of telescopic pedestal (A) as shown. To restrict rotation
of LCD screen to 90°, lineup rear set screw with slot
and tighten where shown in detail 3 using 3 mm allen
wrench (N). To completely restrict rotation, tighten rear
set screw using 3 mm allen wrench (N).
SET SCREWS
B
A
L
SLOT
REAR SET
SCREW
DETAIL 3
Turn tube nut counterclockwise to loosen. Gently hold pivot head
(B) down with one hand, and gently press on lock ball with the other
hand. Lock ball must be inserted into outer tube to obtain up and down
movement. Do not insert lock ball all the way into the inner tube.
Adjust to desired height making sure to locate lock ball into one the
four holes as shown.
NOTE: Setting the lock ball in the lowermost hole requires the removal
of the inner white plastic ring. To do this set the lock back in a
different hole. Slowly unscrew the tube nut until it comes off threads.
Remove the white plastic ring inside the tube nut. Retighten the tube
nut. Adjust the height until the lock ball reaches the lowermost hole.
TUBE NUT LOCK BALL
A
BACK VIEW
B
INNER TUBE
OUTER TUBE
ISSUED: 09-30-02 SHEET #: 090-9085-6 07-23-13
5 of 5
Route cord(s) through cable clips for cord management.
Note: Ensure the cords have enough slack for proper clearance
and function.
Turn screen clockwise by hand for landscape or portrait
orientation.
CABLE
CLIPS MONITOR
CORD(S)
For tilt adjustment use one 4 mm allen wrench (M) to
hold socket screw in place and the other 4 mm allen
wrench (M) to turn the socket screw clockwise to tighten
and counterclockwise to loosen as shown.
MSOCKET
SCREW
M
© 2013 Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Indice
Altri manuali peerless-AV Rack e supporto
peerless-AV
peerless-AV ST940-EXA Manuale utente
peerless-AV
peerless-AV DSF210-GHC Manuale utente
peerless-AV
peerless-AV ACC170 Manuale utente
peerless-AV
peerless-AV SF670 Manuale utente
peerless-AV
peerless-AV EWP-49XE4F Manuale utente
peerless-AV
peerless-AV KLR62232 Manuale utente
peerless-AV
peerless-AV DCS400 Manuale utente
peerless-AV
peerless-AV SR555E Manuale utente
peerless-AV
peerless-AV ACC310 Guida
peerless-AV
peerless-AV DS-LEDZRD Series Manuale utente
peerless-AV
peerless-AV DS-LEDA27-4x4 Manuale utente
peerless-AV
peerless-AV KIL740-EUK Manuale utente
peerless-AV
peerless-AV PR598-M Manuale utente
peerless-AV
peerless-AV CMJ450 Guida
peerless-AV
peerless-AV HA746-STB Manuale utente
peerless-AV
peerless-AV DST980-3 Manuale utente
peerless-AV
peerless-AV PRG-UNV Manuale utente
peerless-AV
peerless-AV RMI2C Manuale utente
peerless-AV
peerless-AV SR560-HUB2 Manuale utente
peerless-AV
peerless-AV TVA750 Manuale utente
