PEERLESS PARAMOUNT PRTLU Manuale utente
ISSUED: 11-03-09 SHEET #: 202-9395-1
Paramount™ Universal Tilt Wall Mount
for 37" - 60" Flat Panel Screens
Max UL Load Capacity: 200 lb (90 kg)
Model: PRTLU
Installation Guide
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
This product was designed to be installed on wood stud walls and solid concrete (2000 psi
density minimum) or cinder block walls. Before installing make sure the supporting surface will
support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur or product may fail. Never exceed the Maximum UL
Load Capacity. This product is intended for indoor use only. Use of this product outdoors could
lead to product failure or personal injury. For support please call customer care at 1-800-865-2112.
WARNING
2 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
A(1)
S(4)
M4 x 12 mm
D(4)
E(4)
F(4)
M4 x 25 mm
G(4)
M5 x 12 mm
H(4)
M5 x 25 mm
I(4)
M6 x 12 mm
J(4)
M6 x 20 mm K(4)
M6 x 25 mm
L(4)
M6 x 30 mm
M(6)
M8 x 16 mm N(4)
M8 x 25 mm
O(4)
M8 x 40 mm
P(4)
ID .22" (5.6 mm)
Q(4)
ID .34" (8.7 mm) R(6)
B(1)C(1)
Tools Needed for Assembly
• studnder("edgetoedge"stud
nderisrecommended)
•phillips screwdriver
•drill
• 5/32"(4mm)bitforwoodstudwall
• 5/16"(8mm)bitforconcreteand
cinder block
• level
• hammer (optional)
3 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
Installation to Double Wood Stud Wall
1
Use wall plate (A) as a template, make sure it is level, and mark four mounting holes along the center
linesofthewoodstuds.Drillfour5/32"(4mm)dia.holes2.5"(64mm)deep.Levelwallplate(A) and
attach to wall with four wood screws (D)intostudcenter.Useofanedgetoedgestudnderishighly
recommended.Tightenscrewsrmly,butdonotovertighten.
A
D
Do not over tighten screws, or
damage may occur.
TOP CUTAWAY VIEW
Wood screws must
center in stud.
STUD
D
A
WARNING WARNING
4 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
Installing to Solid Concrete or Cinder Block
1
Level wall plate (A)anduseasatemplatetomarkfourmountingholes.Drillfour5/16"(8mm)dia.
holes to a minimum depth of 2.5" (64 mm). Insert four anchors (E) into holes and secure wall plate (A)
with four screws (D).Tightenscrewsrmly,butdonotovertighten.
D
E
A
SOLID CONCRETE
CINDER BLOCK
5 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
1
2
E
A
E
D
concrete
Place plate (A) over anchors (E). Secure with screws (D). Tighten screws.
Drill holes and insert anchors (E).
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimum
of1-3/8"(35mm)ofactualconcretethicknessintheholetobeusedfortheconcrete
anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-
ally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90
specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrillthe
hole instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
• Alwaysattachconcreteanchorsdirectly to load-bearing concrete.
WARNING
CUTAWAY VIEW
INCORRECT
CORRECT
plaster/
drywall
concrete
plaster/
drywall
wall plate
wall plate
CORRECT
WARNING
concrete
6 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
Topreventscratchingthescreen,setaclothonaat,levelsurfacethatwillsupportthe
weight of the screen. Place screen face side down. Refer to screen manufacturers instruc-
tions or customer service, for removing any knobs, base, cover, or screw(s) on the back of
the screen to prepare mounting. These need to be removed to allow the adapter brackets to
beattached.Selectthesmall,medium,largeorextralargescrewsfromthebafedfastener
packthenattachtiltbracketstoscreenfollowinggure2.1or2.2.
NOTE: Be sure to attach tilt brackets with handles facing outward as shown below.
NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes
should also be used where the fasteners and screens allow. Verify that all holes are properly
aligned, and then tighten screws using a phillips screwdriver.
B
CENTER BRACKETS VERTICALLY
ON BACK OF SCREEN
X
C
X
HANDLES FACE OUT
Notes:
• Thenumberoffastenersused
will vary, depending upon the
type of screen.
• Multi-washersandspacersmay
not be used, depending upon
the type of screen.
• Usethecorrespondingholein
the multi-washer that matches
your screw size.
MEDIUM HOLE
FOR M5 SCREWS
SMALL HOLE
FOR M4 SCREWS
LARGE HOLE
FOR M6 SCREWS
MULTI-WASHER
NOTE: "X" dimensions should be equal.
2
Installing Adapter Brackets
7 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
g.2.1
SCREW
MULTI-WASHER
ADAPTER
BRACKET
(Bor C)
SCREEN
For Bump-out or Recessed Back Screen
2-2 Refer to screen compatibility chart to determine the proper fastener to use. Visit
www.peerlessmounts.com/2for a full screen compatibility chart for this mount.
Begin with longer length screw, hand thread through multi-washer, adapter bracket and
spacer in that order into screen as shown below. Screw must make at least three full turns
intothemountingholeandtsnugintoplace.Donotovertighten.Ifscrewcannotmake
threefullturnsintothescreen,selectalongerlengthscrewfromthebafedfastenerpack.
Repeat for remaining mounting holes, level brackets and tighten screws.
2-1 Refer to screen compatibility chart to determine the proper fastener to use. Visit
www.peerlessmounts.com/2for a full screen compatibility chart for this mount.
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket
into screen as shown below. Screw must make at least three full turns into the mounting hole
andtsnugintoplace.Donotovertighten.Ifscrewcannotmakethreefullturnsintothe
screen,selectalongerlengthscrewfromthebafedfastenerpack.Repeatforremaining
mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
For Flat Back Screen
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
• Ifscrewsdon'tgetthreecompleteturnsinthescreeninsertsorifscrewsbottomoutand
bracket is still not tightly secured, damage may occur to screen or product may fail.
WARNING
SCREW
SCREEN
SPACER
MULTI-WASHER
ADAPTER
BRACKET
(Bor C)
g.2.2
8 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
Mounting and Removing Flat Panel Screen
3
Tension Adjustment of Ratchet Handle: Adjust tension in tilt brackets (B & C) by rotating ratchet
handle. NOTE: If obstruction prevents ratchet handle from rotating, pull handle out while turning will
allow handle to reposition without tightening. Release and turn handle to tighten or loosen.
Mounting Screen: Ratchet handle must be in the up or down position or interference will occur while
hooking tilt brackets to wall plate (A). Slowly hook tilt brackets (B & C) onto wall plate (A) and swing
screendownasshowning.3.1.Tiltbrackethooksmustfullyengagewallplateasshownindetail1.
Alwaysuseanassistanttosafelyliftandpositiontheatpanelscreen.Usingaphillipsscrewdriver,turn
safety screws on tilt brackets (B & C) clockwise till screw tip securely contacts wall plate as shown in cross
section.
Removing Screen: To remove screen from mount, loosen safety screws, swing screen away from
mount, and lift screen off of mount.
Failure to lock brackets (B &C) with safety
screws can cause sceen to come off mount
if hit accidentally.
WARNING
g3.1
RATCHET
HANDLE
SAFETY
SCREW
DETAIL 1
A
CROSS SECTION
B & C
B & C
A
9 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1
g.3.2
Screen Adjustment: Screen can be adjusted horizontally by loosening safety screws on tilt
brackets (B & C)threefullturnswithaphillipsscrewdriver.Adjustscreenasshowningure
3.2. Tighten safety screws on tilt brackets till screw tip securely contacts wall plate as shown
in cross section.
Adjusting the Tilt Angle of the Flat Panel Screen
4
For preset tilt angles use Increlok™ and for custom tilt angle use ratchet handle.
INCRELOK™:The screen can be locked into a pre-set tilt position of -5°, 0°, 5°, 10°or 15°. Use
locatorholetondtiltpositionholeandtiltscreentoalignholes.TightenIncreLok™tiltlocking
screws on both tilt brackets to lock tilt as shown in detail 2.
Ratchet Handle: Loosen ratchet handle (refer to step 3 for tension adjustment of handle). Push or
pullfromtoporbottomofscreentoadjusttiltasshowningure4.1.Thetiltcanbeadjustedtoa
maximum of 15° forward or 5° backward.
DETAIL 2
g4.1
IncreLok™ TILT
LOCKING SCREW
LOCATOR
HOLE
RATCHET
HANDLE
TILT
POSITION
HOLES
3-1
Indice
Lingue:
Altri manuali PEERLESS Supporto TV
PEERLESS
PEERLESS SUF640P and assembly Guida
PEERLESS
PEERLESS PARAMOUNT PT630 and assembly Guida
PEERLESS
PEERLESS SMARTMOUNT SA763PU Manuale utente
PEERLESS
PEERLESS Paramount PP730 and assembly Guida
PEERLESS
PEERLESS WSP 320 Manuale utente
PEERLESS
PEERLESS SA730P and assembly Guida
PEERLESS
PEERLESS HP450 Manuale utente
PEERLESS
PEERLESS ACC 908 Guida
PEERLESS
PEERLESS SmartMount SF680 and assembly Guida
PEERLESS
PEERLESS PARAMOUNT PRFLU Manuale utente
PEERLESS
PEERLESS Smartmount ST640 Manuale utente
PEERLESS
PEERLESS DSX200 Guida
PEERLESS
PEERLESS HAVE1 FPZ-655 Manuale utente
PEERLESS
PEERLESS WSP700 Manuale utente
PEERLESS
PEERLESS SMART MOUNT SF 16D and assembly Guida
PEERLESS
PEERLESS Smartmount ST632 Manuale utente
PEERLESS
PEERLESS SR1G Manuale di istruzioni
PEERLESS
PEERLESS LWS310/BK Guida
PEERLESS
PEERLESS PARAMOUNT PFT640 and assembly Guida
PEERLESS
PEERLESS PLCK-1 Guida
